Matt,
The "Solo" buss amp is on the Monitor Module. I think this problem
is really starting to look like it is confined to the Stereo Master module.
best,
Ike
On 1/27/2010 3:43 PM, Matt Syson wrote:
Hi
You still haven't said if it is 50Hz or 100. (60 or 120). That would
tell us if it is a faulty power supply or something to do with the
wiring.
The solo bus has a lot less 'gain' than the others unless you operate
all the solos at once.
Matt S
BARAK KOREN wrote:
hi ike,
i have checked if the hum was caused due to external induction...
not. i moved the console 50m away, got the same problem.
i also checked and it seems that the hum is present on mix bus and on
the group out busses but is not present on the solo bus??
so this means there is current running on the chassis. i wrote a help
request to mike s. and i hope i'll solve it asap.
i have a wooden cover i tried covering with metal, still no effect.
i wrote a help request to mike s. and i hope i'll solve it asap.
if anybody has a creative idea, please.
thanx all for help and effort.
Barak Koren
On Jan 27, 2010, at 4:45 PM, Ike Zimbel wrote:
Hi Barak,
Is the bottom cover wood or metal? If it's wood, it will make no
difference, if metal, it may help to mount it.
best,
Ike
On 1/26/2010 4:15 PM, BARAK KOREN wrote:
no induction problems experienced, psu 3m far from console,
consoles bottom cover is not mounted.
moving the psu don't make any difference.
yes both psu are connected with diodes.
thanx
barak
On Jan 26, 2010, at 9:47 PM, Ike Zimbel wrote:
What is your studio like for noise in general? Do you have
problems with single coil pick-up guitars (like a Strat...)
picking up noise in the room? Are you in some part of the building
near heavy power lines or transformers?
iz
On 1/26/2010 3:40 PM, BARAK KOREN wrote:
mixer is not connected to any thing ...
barak
On Jan 26, 2010, at 9:37 PM, Matt Syson wrote:
Hi
If it is 50 Hz then it is probably induction from external
wiring. PSU related 'hums' are usually double (100) or triple
the mains frequency.
Matt S
BARAK KOREN wrote:
ike hi,
Back to the elite 40 channels 1986 humming issue.
i recapped and refurbished both psu,i changed connectors to NL8
and i measured 17v on motherboard, so thats fine.
the two psu are connected parallel for the whole console(not
like some modes made ,one psu for each side of the master
section).
The mixer is quite when all channels muted.
The hum (about 50hz) appears when channels are ON (faders down)
and is present on all channels.
reading this:
If / when you re-do the PS connection at the board end, it's a
good idea to put in some de-coupling caps on the supply
voltages where they come into the console. About 4700-5600uf at
35-50 volts is good for the +/-18v rails (two caps total),
1,000uf / 50v for the -25v rail, 100uf / 100v for the +48v
rail. The 36 volt rail is kind of optional but use at least a
50v cap, preferably 63v if you put something across it.
Best,
ike
Hi Barak,
Two power supplies makes it WAY more complicated than that.
You might want to check with Mike at Sytek and see if he will
trade your power supplies for an upgraded one that will run
the whole console. Otherwise, we have some talking to do...
I will send the NL-8 pin-out when I get a chance to look for it.
best,
Ike
i still didn't try option one (caps mode on the board side)...
thought you can advice...
Thanx
Barak Koren
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe neotek" in the
message body. If you have any difficulties, or questions
--please send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember
that any message or reply sent to the list will be automatically
forwarded to all subscribers.
Vive Le Neotek!
Thanks.
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe neotek" in the
message body. If you have any difficulties, or questions --please
send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that
any message or reply sent to the list will be automatically
forwarded to all subscribers.
Vive Le Neotek!
Thanks.
--
Ike Zimbel
Zimbel Audio Productions Ltd.
Toronto
416-720-0887
"Studio House Calls". Authorized Warranty service for Allen&
Heath, Clear-Com, Drawmer, Soundcraft, SPL and Yamaha. Repairs and
upgrades to analog audio equipment including: AMEK, dbx, Neve,
Neotek, MCI, Soundcraft and more. Ask about our RF Frequency
co-ordination services!
www.zimbelaudio.com
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe neotek" in the
message body. If you have any difficulties, or questions --please
send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that
any message or reply sent to the list will be automatically
forwarded to all subscribers.
Vive Le Neotek!
Thanks.
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe neotek" in the
message body. If you have any difficulties, or questions --please
send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that
any message or reply sent to the list will be automatically
forwarded to all subscribers.
Vive Le Neotek!
Thanks.
--
Ike Zimbel
Zimbel Audio Productions Ltd.
Toronto
416-720-0887
"Studio House Calls". Authorized Warranty service for Allen& Heath,
Clear-Com, Drawmer, Soundcraft, SPL and Yamaha. Repairs and upgrades
to analog audio equipment including: AMEK, dbx, Neve, Neotek, MCI,
Soundcraft and more. Ask about our RF Frequency co-ordination services!
www.zimbelaudio.com
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe neotek" in the
message body. If you have any difficulties, or questions --please
send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that
any message or reply sent to the list will be automatically
forwarded to all subscribers.
Vive Le Neotek!
Thanks.
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe neotek" in the
message body. If you have any difficulties, or questions --please
send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that any
message or reply sent to the list will be automatically forwarded to
all subscribers.
Vive Le Neotek!
Thanks.
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe neotek" in the
message body. If you have any difficulties, or questions --please send
an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that any
message or reply sent to the list will be automatically forwarded to
all subscribers.
Vive Le Neotek!
Thanks.
--
Ike Zimbel
Zimbel Audio Productions Ltd.
Toronto
416-720-0887
"Studio House Calls". Authorized Warranty service for Allen& Heath, Clear-Com,
Drawmer, Soundcraft, SPL and Yamaha. Repairs and upgrades to analog audio equipment
including: AMEK, dbx, Neve, Neotek, MCI, Soundcraft and more. Ask about our RF Frequency
co-ordination services!
www.zimbelaudio.com
------
View the list online at: http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to mailto:[email protected] with
"unsubscribe neotek" in the message body. If you have any difficulties, or
questions --please send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that any message
or reply sent to the list will be automatically forwarded to all subscribers.
Vive Le Neotek!
Thanks.
