this message (re pad sizes) was the sort direction i was hoping when i started this thread
so we are saying that maybe yes there is an impact on design ?
very interesting ...
ds
_______________________________________________________________________ Integrated Controls, Inc. Tel: 415-647-0480 EXT 107 2851 21st Street Fax: 415-647-3003 San Francisco, CA 94110 www.integratedcontrolsinc.com
Brooks,Bill wrote:
Hi Rene,
It sounds like a difficult problem. One thing to think about too, it how the new soldering process will affect
pad geometries... your 0603 resistors for example, may need to have larger
pads, or smaller pads... depending on the wicking and surface tension of the
new lead free alloy solders... you might see more failed soldering issues or
'tomb-stoning' in some cases or parts may float on the surface tension and
not actually wet to the solder with the slightest oxidation on the component
terminations...
It seems poorly timed for companies to have to wrestle with this issue at this time... but here we are. You say that Japan has conquered these issues already, could you site some examples? I was not aware of that... It might be interesting reading...
Best regards,
Bill Brooks - KG6VVP PCB Design Engineer , C.I.D.+, C.I.I. Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 e-mail:[EMAIL PROTECTED] http://www.dtwc.com http://pcbwizards.com
-----Original Message-----
From: Rene Tschaggelar [mailto:[EMAIL PROTECTED] Sent: Monday, December 06, 2004 1:06 PM
To: Protel EDA Discussion List
Subject: Re: [PEDA] Lead free re design
Dennis, as European, I don't have the option to stay out of the lead free, thus I had to get some information in the last few months. While my pcb assembler acknowledges that he doesn't have the proper process parameters, he said the problems are multiple. The lifetime is reduced, because the tinn eats the copper, meaning after about 7 years there might be a gap between the copper trace and the tinned part. The lead till now supressed this effect. Silver would solve it at increased cost, beside that silver can grow whiskers of several mm in length, thus shorting a 0603. If the silver-tin was heated above 230 degrees that would not happen. The increased melting point of the new tin alloys is between 217 and 220 degrees, whereas the lead-tin was at 188 degrees. This can give problems with subunits such as DC/DC converters or overized oscillators. These shouldn't fall apart when being subject to the normal soldering process. Meaning they internally have to be soldered with something higher melting. With the new 220 degree tin alloy this margin became smaller.
There are multiple exceptions to follow the lead free. The automobile industry is amongst them. Ok, I could classify my products as automobile classified, and earn less/more. But what is my customer going to do ?
That some call this new requirement a chessplay to shorten the lifecycle and thus increase the turnover is as little helping as that some claim it was invented to keep the asian competition out. Japan started this process 15 years ago and introduced it throughout, apparently having solved the problems. To me it is a task on the list.
Rene
Dennis Saputelli wrote:
i may have posted this before but don't recall an answer
someone has asked me if there are *design* issues re pc bd designs and the movement to lead-free
i said i didn't think so, but then i wondered about the elevated temperatures and surface finsishes
what is the proper call out for surface finish of a pcb for lead free ? and are there any actual design issues (as opposed to call-out issues)
and also
can you use the new lead free components in a standard 'lead-full' process ? (thanks for 'lead-full' Ivan)
and what about cleaning under CSPs and BGAs ? is the standard water based OA fluz a problem ? seems like it would be
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages: mailto:[EMAIL PROTECTED]
Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages: mailto:[EMAIL PROTECTED]
Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
____________________________________________________________ You are subscribed to the PEDA discussion forum
To Post messages: mailto:[EMAIL PROTECTED]
Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
