[Elecraft] Elecraft XG2 for Sale

[Irwin Darack]

I have an Elecraft XG2 Signal Generator for Sale .

This is a used Elecraft's XG2 3-Band Test Oscillator Signal Generator. The
XG2 uses a crystal oscillator and is ideal for receiver testing, alignment
and S-Meter calibration.

* RF Output Level: 1 µV (-107 dBm) and 50 µV (-73 dBm = S9)
  *Output Accuracy: Typically Better than +/-2 dB at 25 deg. C
* Frequencies: 3.579.5, 7.040 and 14.060 MHz
* Switch selectable output
* Uses a CR2032 Lithium Battery
* Red LED Light used to indicate power on
* Instruction manual included

Asking $70.(or reasonable offer) + Shipping - Con USA Only.

Please contact me off the reflector: idarack(at) gmail.com

Thanks, Irwin KD3TB







Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] Elecraft K3s For Sale

[Irwin Darack]

This radio has sold.
Thanks for all the interest.

Irwin KD3TB

On Wed, Dec 2, 2020 at 1:41 PM Irwin Darack  wrote:

> i am selling my Elecraft K3s and will post here before placing on Ebay.
>
> Elecraft K3s - this radio was built by kit and is in excellent condition.
>
>- Serial # 10354
>- 100W Upgrade
>- Filters are: 2.7kHz, 2.1 kHz & 400 Hz.
>- Digital Voice Recorder
>- ATU - Antenna Tuner
>- Kit Manual & Owners Manual
>- Power Cord
>
> I am also including the following books.
> Fred Cady's ' The Elecraft K3s and P3 Manual'
> Fred Cady's 'Elecraft Macro Programming Manual'
>
> I am asking $2,500 (or best reasonable offer) with Free Shipping to
> Continental US. Pick up or  local delivery from Doylestown, PA (-$100).
>
> If interested, please contact me off reflector.
> --
> Irwin KD3TB
>
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] Elecraft K3s For Sale

[Irwin Darack]

 i am selling my Elecraft K3s and will post here before placing on Ebay.

Elecraft K3s - this radio was built by kit and is in excellent condition.

   - Serial # 10354
   - 100W Upgrade
   - Filters are: 2.7kHz, 2.1 kHz & 400 Hz.
   - Digital Voice Recorder
   - ATU - Antenna Tuner
   - Kit Manual & Owners Manual
   - Power Cord

I am also including the following books.
Fred Cady's ' The Elecraft K3s and P3 Manual'
Fred Cady's 'Elecraft Macro Programming Manual'

I am asking $2,500 (or best reasonable offer) with Free Shipping to
Continental US. Pick up or  local delivery from Doylestown, PA (-$100).

If interested, please contact me off reflector.
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] [GoFRC] Elecraft K3s Second Receiver for sale

[Irwin Darack]

The 2nd Receiver has been sold.

Thanks, Irwin KD3TB

On Wed, Sep 2, 2020 at 3:55 PM Irwin Darack via groups.io  wrote:

> I forgot to add that I have the Sub Receiver Installation Manual
>
> Irwin KD3TB
>
> On Wed, Sep 2, 2020 at 3:28 PM Irwin Darack  wrote:
>
>> I have an Elecraft K3s KRX3A, Second Receiver for Sale.
>>
>> It contains the
>>
>>- Installed in the Sub Receiver are the KRX3A Main Circuit Board,
>>Mixer Board, KNB3 Board & KFL3A-2.7 Filter
>>- KSYN3A  Synthesizer
>>- Auxiliary DSP Circuit Board
>>- Sub In Board
>>- Sub Out Board
>>
>> I do not have the TMP Cable with the BNC Connector. This can be ordered
>> from Elecraft (E850344 TMP-BNC Cable Bag).
>>
>> Asking $700 which includes free shipping to CON USA.
>>
>> Please contact me off the reflector at IDarack(at)gmail.com
>>
>> --
>> Irwin KD3TB
>>
>>
>>
>
> --
> Irwin KD3TB
>
>
>
>
> _._,_._,_
>
>
> --
>
>
> Groups.io Links:
>
>
>
>
>
>
>
> You receive all messages sent to this group.
>
>
>
>
>
>
>
>
>
>
>
> View/Reply Online (#33497) <https://groups.io/g/GoFRC/message/33497> |
>
>
>
>
>
> Reply To Sender
> 
>
>
>
> | Reply To Group
> 
>
>
>
>
>
>
>
> |
>
>
>
>
>
>
>
> Mute This Topic <https://groups.io/mt/76590605/691012>
>
>
>
>
>
> | New Topic <https://groups.io/g/GoFRC/post>
>
>
>
>
>
>
>
>
>
>
>
>
>
> Your Subscription <https://groups.io/g/GoFRC/editsub/691012> |
>
> Contact Group Owner  |
>
>
>
> Unsubscribe <https://groups.io/g/GoFRC/unsub>
>
>
>
> [idar...@gmail.com]
>
>
> _._,_._,_
>
>
>
>
> --
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] Elecraft K3s Second Receiver for sale

[Irwin Darack]

I forgot to add that I have the Sub Receiver Installation Manual

Irwin KD3TB

On Wed, Sep 2, 2020 at 3:28 PM Irwin Darack  wrote:

> I have an Elecraft K3s KRX3A, Second Receiver for Sale.
>
> It contains the
>
>- Installed in the Sub Receiver are the KRX3A Main Circuit Board,
>Mixer Board, KNB3 Board & KFL3A-2.7 Filter
>- KSYN3A  Synthesizer
>- Auxiliary DSP Circuit Board
>- Sub In Board
>- Sub Out Board
>
> I do not have the TMP Cable with the BNC Connector. This can be ordered
> from Elecraft (E850344 TMP-BNC Cable Bag).
>
> Asking $700 which includes free shipping to CON USA.
>
> Please contact me off the reflector at IDarack(at)gmail.com
>
> --
> Irwin KD3TB
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] Elecraft K3s Second Receiver for sale

[Irwin Darack]

I have an Elecraft K3s KRX3A, Second Receiver for Sale.

It contains the

   - Installed in the Sub Receiver are the KRX3A Main Circuit Board, Mixer
   Board, KNB3 Board & KFL3A-2.7 Filter
   - KSYN3A  Synthesizer
   - Auxiliary DSP Circuit Board
   - Sub In Board
   - Sub Out Board

I do not have the TMP Cable with the BNC Connector. This can be ordered
from Elecraft (E850344 TMP-BNC Cable Bag).

Asking $700 which includes free shipping to CON USA.

Please contact me off the reflector at IDarack(at)gmail.com

-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] KPA 500

[Irwin Darack]

Agreed. Many people buy the cheap ones made in Chinaand they fail.

Irwin KD3TB

On Fri, Apr 10, 2020 at 12:28 PM Jim Brown 
wrote:

> On 4/10/2020 8:45 AM, Irwin Darack wrote:
> > In my experience, coax connectors, barrel connectors, etc. are always
> fail
> > points when there is a sudden increase in SWR as power is increased. They
> > oxidize over time and sometimes just reconnecting or replacing is the
> first
> > step before taking the amp apart.
>
> If this is happening, I'd suspect 1) the connectors have gotten wet or
> 2) the are JUNK connectors. If they aren't labeled "Amphenol," they're
> JUNK.
>
> 73, Jim K9YC
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] KPA 500

[Irwin Darack]

In my experience, coax connectors, barrel connectors, etc. are always fail
points when there is a sudden increase in SWR as power is increased. They
oxidize over time and sometimes just reconnecting or replacing is the first
step before taking the amp apart.


Irwin KD3TB

On Fri, Apr 10, 2020 at 11:24 AM Don Wilhelm  wrote:

> Alan,
>
> That does sound like an antenna problem - balun heating, a loose or bad
> connection somewhere.
>
> Try that same test into a dummy load - if it shows the same behavior,
> then you can blame the KPA500, but if not blame the antenna system.
>
> 73,
> Don W3FPR
>
> On 4/10/2020 7:26 AM, Alan - G4GNX wrote:
> >
> > I have a strange fault a couple of times recently, where the SWR starts
> > to increase during the time of a single 'over'. I've been using the K3S
> > set at 100W out, via the KPA500 (in standby) and the KAT500 tuner,
> > without any problem, but after I've switched the linear to Operate and
> > driving it to 200W, the SWR creeps up. I don't think it's an antenna
> > issue, but a possible heat problem with the KPA500. I watched the
> > temperature display on the KPA500 and initially on Standby it shows
> > about 38 degrees C. After transmitting at 200W the temperature slowly
> > rises above 60 degrees C, but the fan doesn't cut in. Does anyone know
> > if this is normal behavior and what temperatures I should expect to see?
> > I have tested the fan via the Menu function and it works as expected.
> >
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] K4 news?

[Irwin Darack]

I am curious to know if the reduction in manufacturing in China, do to the
COVID-19 virus, is having an affect on the ability of Elecraft to obtain
parts? The area of China that is the epicenter is a major manufacturer of
electronic components.

Irwin KD3TB



On Wed, Mar 4, 2020 at 6:11 PM Rick Miller - N1RM  wrote:

> Very clever post.
>
> When they announced the last delay, there was a statement that there would
> be more frequent updates.  Perhaps, if nothing else, this thread will
> provide motivation for another update.  Since many of us are "investors" in
> the K4, it seems reasonable to ask.
>
> 73 and hope your twitter remains under control!
> Rick
> N1RM
>
>
>
> --
> Sent from: http://elecraft.365791.n2.nabble.com/
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] KPA500 - Advantage of min fan speed?

[Irwin Darack]

During CQWW RTTY this weekend I ran mine at level 3. Normally I keep it at
the  NOR setting.  When I was in the S mode the KPA500 stayed at this
level. When I was in Run mode the KPA500 would occasionally go to the
highest speed when working a pile up. My antennas are pretty much tuned and
I kept my output between 300 & 400 W.

Irwin KD3TB



On Sun, Sep 29, 2019 at 10:40 PM Andy Durbin  wrote:

> The KPA500 offers a minimum fan speed setting which is settable by menu or
> serial command.  Some posters have advocated setting a minimum fan speed
> higher than zero, presumably thinking it offers some advantage in thermal
> management.
>
> Does anyone have any hard data that shows that the KPA500 runs cooler, or
> with lower peak fan speed, when minimum fan speed is set above zero.
>
> Running a rigorous test may not be easy since it would seem to require the
> same ambient temperature, same finals starting temperature, same TX
> periods, and same antenna system load.
>
> I'm curious because, before CQ-WW-RTTY I configured my KPA500 to set min
> fan speed to 1 at start of TX and reset min speed to zero 30 seconds after
> stop of TX.  Of course the fans ran faster than min speed during TX but I
> don't have any feel for whether the higher speeds were any more protracted
> than before the min speed change.
>
> Please share you experience of using min fan speed greater than zero, and
> any data if you have it.
>
> 73,
> Andy, k3wyc
>
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] KPA500 AC power

[Irwin Darack]

Unless you are having a problem, save your money.  I have two KPA500’s, one
plugged into a 220V line at my main house and the other into a 110V line at
my beach house and have never seen a difference in performance. In
addition, on a number of contests Dx’peditions, were I have my K3s, KPA500
& laptop plugged into the same 110V line, I have not had a problem.
Happy Holidays
Irwin KD3TB

On Wed, Dec 12, 2018 at 7:14 PM Tom Berry  wrote:

> Is there any advantage to use 220 V over 110 V on the KPA500?
>
> Is it worth having an electrician come to the house and install a 220 V
> outlet for it?
>
>
> Thanks
>
> Tom AA4VV
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Elecraft Trade show list, No Dayton?

[Irwin Darack]

Glad to see ...thought I was going to miss my favorite vendor at Dayton.
irwin KD3TB

On Sat, Jan 27, 2018 at 7:01 PM, Wayne Burdick <n...@elecraft.com> wrote:

> Oversight. We’re always at Dayton, four booths wide
>
> Wayne
> N6KR
>
> 
> http://www.elecraft.com
>
> > On Jan 27, 2018, at 1:22 PM, Irwin Darack <idar...@gmail.com> wrote:
> >
> > In the Elecraft January Newsletter they listed the Trade shows they are
> > attending this year. Unless I am missing something, Dayton was not on the
> > list?
> >
> > *Trade Show Calendar*
> >
> > Below is a list of trade shows that we're planning to attend.  We'll let
> > you know if we add any more shows to our list.  It you're attending any
> of
> > these events, come on by and say hello!
> >
> >
> >   - Feb 3- FrostFest, Richmond, VA.
> >   - Feb 9-11  - Hamcation, Orlando, FL.
> >   - April 19-22  - International DX
> >   Convention, Visalia, CA.
> >   - June 1-3  - SeaPac, Seaside, OR.
> >   - June 1-3  - Friedrichshaven, Germany
> >   - June 8-10  - Hamcon, Plano, TX.
> >   - August 18-19  - Huntsville, Huntsville,
> AL.
> >   - Sept 7-9  - Boxboro Hamfest, Boxborough,
> MA
> >   - Oct 19-21  - Pacificon, San Ramon, CA.
> >
> >
> > Irwin, KD3TB
> > --
> > Irwin KD3TB
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to n...@elecraft.com
>



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Elecraft Trade show list, No Dayton?

[Irwin Darack]

In the Elecraft January Newsletter they listed the Trade shows they are
attending this year. Unless I am missing something, Dayton was not on the
list?

*Trade Show Calendar*

Below is a list of trade shows that we're planning to attend.  We'll let
you know if we add any more shows to our list.  It you're attending any of
these events, come on by and say hello!


   - Feb 3- FrostFest, Richmond, VA.
   - Feb 9-11  - Hamcation, Orlando, FL.
   - April 19-22  - International DX
   Convention, Visalia, CA.
   - June 1-3  - SeaPac, Seaside, OR.
   - June 1-3  - Friedrichshaven, Germany
   - June 8-10  - Hamcon, Plano, TX.
   - August 18-19  - Huntsville, Huntsville, AL.
   - Sept 7-9  - Boxboro Hamfest, Boxborough, MA
   - Oct 19-21  - Pacificon, San Ramon, CA.


Irwin, KD3TB
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] OK to place P3 directly on top of K3?

[Irwin Darack]

I have my P3 and an external speaker on top of my K3s with no problem.

Irwin, KD3TB

On Tue, Oct 3, 2017 at 6:55 PM Barry  wrote:

> Looking at some shack redecorating and one possibility is placing the P3
> directly on top of the K3/100.  Is that OK?
>
> Barry W2UP
>
>
>
> --
> Sent from: http://elecraft.365791.n2.nabble.com/
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Low Tx Data Sound Output volume

[Irwin Darack]

I am not sure if this is a Windows 10 problem or something changes in my
K3s settings and want to see if others have experienced the same thing?

When the K3s is in Tx Data (PSK 31 and RTTY) - AFSK -A LSB, I now find that
the data output (sound) is no much lower than when just in LSB mode. This
seems to have occurred with the latest Windows 10 update. Hence in this
weekends CQWW RTTY contest, I could only use MMTTY with the K3s in LSB mode
and not Tx Data mode.  I am not sure if it changed something with the Codec
driver or by some fluke, something changes in the K3s settings. Hence, I
ran the contest in LSB versus Tx Data.
Thanks,
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Lulu discount code

[Irwin Darack]

Thanks, I ordered today - great price.
Fred's books are excellent. Highly recommend to anyone using a K3 or K3s
radio.

Irwin KD3TB

On Wed, Sep 13, 2017 at 3:06 PM, Edward Seeliger 
wrote:

> The correct code is SAVENOW30.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Dual -Watch and KRX3A sub-receiver install in a K3s

[Irwin Darack]

>From everyone's comments, I realize that to have dual watch ( listen to two
different frequency on the same band) on my K3s, I need to install the KRX3A
sub-receiver. I have two K3s that I have built, one with the KRX3A and the
second without. I am thinking of upgrading the second one with the
sub-receiver now.

To install a KRX3A in an already built K3s do I need to remove the front
panel? I am hoping that I do not as to reinstall the front panel you have
to be very careful not to bend a pin. I realize that I have to install some
new additional stand-offs on the main RF board. I have reviewed the KRX3A
install instructions and it's a little confusing on the difference in a
older K3 versus a K3s. It appears that you have to take the front panel
totally apart?

Looking forward to see everyone at Dayton (Xenia).

Thanks, Irwin KD3TB
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Dual Receive on same band in K3s

[Irwin Darack]

I have a K3s without the sub-receiver installed. Is there a way to listen
to two different frequencies on the same band without a sub-receiver using
a stereo headset ?
Thanks.
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3/K3s Macro Book

[Irwin Darack]

I am hoping they have some forsale at Dayton so I do not have to pay
shipping.

Irwin , KD3TB

On Sat, May 6, 2017 at 8:36 AM ke9uw  wrote:

> Macro book? Where is it available?
>
>
>
> -
> Chuck, KE9UW
> --
> View this message in context:
> http://elecraft.365791.n2.nabble.com/K3-K3s-Macro-Book-tp7630321p7630367.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3/K3s Macro Book

[Irwin Darack]

Will copies of the K3/K3s Macro Book be available for sale at Dayton ?

Irwin KD3TB
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Problem with N1MM+ ansd My K3 in ARRL RTTY Test

[Irwin Darack]

I had the same problem changing the K3s to FSK D verses AFSK A that I
normally use for RTTY whenever I clicked on a spot. Solved the problem by
telling N1MM+ to follow the radio setting.

Irwin KD3TB



On Mon, Jan 9, 2017 at 3:29 PM Nathern Priddy via Elecraft <
elecraft@mailman.qth.net> wrote:

> Did anyone else have the problem I had using MMTTY in N1MM+ with my K3 in
> the ARRL RTTY Contest?  I was operating in the assisted mode.  Whenever I
> clicked on a new spot in the N1MM+ bandspread window, the mode switched
> from FSK D to USB.  I had to push the mode button twice to get back to FSK
> D mode each time I clicked on a new spot.
>
>
>
> I temporarily switched to DXLab Suite and used MMTTY together with
> Commander and Spot Collector.  With that software setup, I could click on a
> new RTTY spot in Spot Collector, and the K3 stayed in FSK D mode.  When I
> switched back to N1MM+, I had the origninal problem for the rest of the
> contest.
>
>
>
> It was a real drag having to reset the mode to FSK D every time I selected
> a new call sign to work.  Any thoughts?
>
>
>
> Barry Priddy - K5VIP
>
> __
>
> Elecraft mailing list
>
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/mmfaq.htm
>
> Post: mailto:Elecraft@mailman.qth.net
>
>
>
> This list hosted by: http://www.qsl.net
>
> Please help support this email list: http://www.qsl.net/donate.html
>
> Message delivered to idar...@gmail.com
>
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Help with macro for spot funtion.

[Irwin Darack]

Mike,

The code for the SPOT function is SWT42. I use it with my K3s in CW and CWT
function turned on. Also, I find that to work best, make sure your FINE
tuning shows all of the decimals in the LCD screen.

I hope this helps,

Happy New Year to all,

Irwin, KD3TB



On Thu, Dec 29, 2016 at 9:51 AM Mike Weir  wrote:

> Good morning all, I am in the process of programing macros to my K-pod. I
> have been successful with all but the spot macro. According to the Elecraft
> K3 and KX3 programmers rev E11 on page 22 I am to enter an open and closed
> single quotation with a period in the middle. Funny thing is I can't seem
> to find the single quotations on the keyboard?
>
>
>
> Help
>
>
>
> Mike
>
>
>
> VE3WDM
>
> __
>
> Elecraft mailing list
>
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/mmfaq.htm
>
> Post: mailto:Elecraft@mailman.qth.net
>
>
>
> This list hosted by: http://www.qsl.net
>
> Please help support this email list: http://www.qsl.net/donate.html
>
> Message delivered to idar...@gmail.com
>
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3s Heil Microphone Settings

[Irwin Darack]

I have two Microphones and looking for recommendations on settings. Current
settings are:

Heil GM-5 Desktop - rPH (Bias Off)

Heil Proset 6 iC Headset - rPH (Bias On)

Any recommendations on the Equilizer settings?

-- 
Thanks and Happy New Year, Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3s - PF1 and PF2 Macros

[Irwin Darack]

Is there a way to set up a Macro's in PF1 and PF2 on the K3s that sets the
Micro Phone Bias on or off in addition to the K-Pod Macros that I already
have?

I want to set PF1 for a Desktop Mic that does not require Bias and PF2 for
a Headset Mic that requires Bias

Thanks and Happy New Year, Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Small Keyboard Recommendation for P3/SVGA

[Irwin Darack]

Do not want wireless. I will be plugging the Keyboard into the USB Keyboard
on the back of the P3/SVGA .

Irwin KD3TB

On Fri, Dec 16, 2016 at 1:55 PM, Ed K1EP <k1ep.l...@gmail.com> wrote:

> Will it work with a wireless keyboard?
>
> On Dec 16, 2016 1:47 PM, "Irwin Darack" <idar...@gmail.com> wrote:
>
>> I am looking for a small keyboard recommendation for the P3/SVGA. I
>> already
>> have it working  with a large keyboard. Would  like to find a mini
>> keyboard
>> instead to save room on my Ham Shack Self.
>>
>> Does Elecraft have a list of compatible Keyboards?
>>
>> Logitec, Microsoft? etc.
>>
>> Thanks and regards,
>>
>> --
>> Irwin KD3TB
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to k1ep.l...@gmail.com
>>
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Small Keyboard Recommendation for P3/SVGA

[Irwin Darack]

I am looking for a small keyboard recommendation for the P3/SVGA. I already
have it working  with a large keyboard. Would  like to find a mini keyboard
instead to save room on my Ham Shack Self.

Does Elecraft have a list of compatible Keyboards?

Logitec, Microsoft? etc.

Thanks and regards,

-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K-POD Macro

[Irwin Darack]

I have had no luck in trying a variety of combinations using the Unlink
VFO, Split and Sub Band commands in the Macro. I know wonder if you can not
create a macro that sends VFO A to one band/frequency and VFO B to another
band/Frequency?

I am hoping that someone from Elecraft who is responsible for the Macro's
can help here before I spend too much more time on this project.

Thanks, Irwin KD3TB

On Mon, Dec 12, 2016 at 6:44 PM, Irwin Darack <idar...@gmail.com> wrote:

>
> On Mon, Dec 12, 2016 at 5:22 PM Don Wilhelm <donw...@embarqmail.com>
> wrote:
>
>> Irwin,
>> Thanks, Irwin
>>
>>
>> My guess is that you do not have VFO IND turned ON in the menu.
>>
>> You are trying to set the VFOs to two different bands and that requires
>>
>> VFO INDependent.  See page 37 of the K3 manual for full disclosure.
>>
>>
>>
>> 73,
>>
>> Don W3FPR
>>
>>
>>
>> On 12/12/2016 5:07 PM, Irwin Darack wrote:
>>
>> > I would like to write a WWV Macro that sends VFO A = 20 Mhz and VFO B =
>> 15
>>
>> > Mhz.
>>
>> >
>>
>> > This sends VFO A to 20 Mhz:  FA0002000;MD5;FB0001500;BW0300;
>>
>> > But does not send VFO B to 15 Mhz
>>
>> >
>>
>> > What am I doing wrong here?
>>
>> >
>>
>> > Thanks,
>>
>> >
>>
>>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K-POD Macro

[Irwin Darack]

I would like to write a WWV Macro that sends VFO A = 20 Mhz and VFO B = 15
Mhz.

This sends VFO A to 20 Mhz:  FA0002000;MD5;FB0001500;BW0300;
But does not send VFO B to 15 Mhz

What am I doing wrong here?

Thanks,
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] New HP Laptop Function Key Problem

[Irwin Darack]

Yes. I have done it with all my laptops.if you search the web you will find
it for your specific Laptop. You have to make the change in the Laptop
Bios.

Irwin



On Wed, Dec 7, 2016 at 9:48 PM Ed Gilliland  wrote:

> Just received a new HP ProBook 455 G3 with Windows 10 Professional. I've
>
> been able to successfully install N1MM+ and the laptop will key my K3s If I
>
> use the mouse and click on the function key that N1MM+ displays or if I
>
> hold the laptop Fn key down and press one of the laptop function keys. Is
>
> there a way to setup the laptop keyboard so that when I press F1 I don't
>
> get "Help" but send N1MM+ F1?  Thanks.
>
>
>
> Ed W5TM
>
> __
>
> Elecraft mailing list
>
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/mmfaq.htm
>
> Post: mailto:Elecraft@mailman.qth.net
>
>
>
> This list hosted by: http://www.qsl.net
>
> Please help support this email list: http://www.qsl.net/donate.html
>
> Message delivered to idar...@gmail.com
>
>
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3USB Drivers

[Irwin Darack]

I am setting up a new 64 bit Windows 7 Pro computer and need to make sure I
have downloaded the correct K3USB Drivers for my K3s.

Following the Elecraft web site link, I downloaded VCP Drivers - CDMV
2.12.24 zip file?

Thanks, Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Computer Boot Up Keys the K3S

[Irwin Darack]

When I boot up my computer it keys the K3s Radio. I seem to remember there
is a setting in the K3s Radio to prevent this?

Irwin KD3TB


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] SVGA/P3 Question -Waterfall Height Problem

[Irwin Darack]

P3 Firmware installed:
MCU = 1.60
SVGA=1.34
FPGA 0-4 = 1.04

I figured out the problem. When SVGA Data is turned on, the SVGA setting on
the P3 does not remember the SVGA P3 Waterfall Height. When SVGA is turned
off, it remembers the original SVGA Waterfall Height setting.   This may
have something to do with that I have the TX Data window screen size at the
lowest level and only use the RX Data Window on the P3/SVGA to copy CW/RTTY.

Irwin KD3TB

On Tue, Oct 18, 2016 at 2:05 PM, Gerald Manthey <kc6...@gmail.com> wrote:

> Mine does this too, but only when displaying decoded text. I have to
> adjust it every time.
>
> > On Oct 18, 2016, at 11:01 AM, Irwin Darack <idar...@gmail.com> wrote:
> >
> > Latest firmware installed
> >
> > Thanks, Irwin KD3TB
> >
> >> On Monday, October 17, 2016, Guy Olinger K2AV <k2av@gmail.com>
> wrote:
> >>
> >> I do not have this problem, and I have P3/SVGA. Do you have all the
> latest
> >> production firmware? Or have you installed a beta?
> >>
> >> 73, Guy K2AV
> >>
> >> On Mon, Oct 17, 2016 at 5:59 PM, Irwin Darack <idar...@gmail.com
> >> <javascript:_e(%7B%7D,'cvml','idar...@gmail.com');>> wrote:
> >>
> >>> I have a P3 with the SVGA board installed + an external monitor.
> >>>
> >>> SVGA Monitor Height = Main
> >>> P3 = 30
> >>>
> >>> When ever I turn on the P3 (and monitor), I need to reset the Waterfall
> >>> Height.  The Height is fine on the P3, but takes up 3/4 of the screen
> on
> >>> the external monitor. The P3 remembers the original Height setting. To
> >>> reset the Waterfall Height on the external monitor, I need to go to
> the P3
> >>> Waterfall Height, make any change in the Height value, and then the
> >>> Waterfall Height on the external monitor corrects itself. Not sure why
> the
> >>> External Monitor requires this and if it has something to do with the
> >>> P3 SVGA board or a monitor setting?
> >>>
> >>> Thanks, Irwin KD3TB
> >>>
> >>>
> >>>
> >>>
> >>> --
> >>> Irwin KD3TB
> >>> __
> >>> Elecraft mailing list
> >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> >>> Help: http://mailman.qth.net/mmfaq.htm
> >>> Post: mailto:Elecraft@mailman.qth.net
> >>> <javascript:_e(%7B%7D,'cvml','Elecraft@mailman.qth.net');>
> >>>
> >>> This list hosted by: http://www.qsl.net
> >>> Please help support this email list: http://www.qsl.net/donate.html
> >>> Message delivered to k2av@gmail.com
> >>> <javascript:_e(%7B%7D,'cvml','k2av@gmail.com');>
> >>>
> >>
> >>
> >
> > --
> > Irwin KD3TB
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to kc6...@gmail.com
>



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] SVGA/P3 Question -Waterfall Height Problem

[Irwin Darack]

Latest firmware installed

Thanks, Irwin KD3TB

On Monday, October 17, 2016, Guy Olinger K2AV <k2av@gmail.com> wrote:

> I do not have this problem, and I have P3/SVGA. Do you have all the latest
> production firmware? Or have you installed a beta?
>
> 73, Guy K2AV
>
> On Mon, Oct 17, 2016 at 5:59 PM, Irwin Darack <idar...@gmail.com
> <javascript:_e(%7B%7D,'cvml','idar...@gmail.com');>> wrote:
>
>> I have a P3 with the SVGA board installed + an external monitor.
>>
>> SVGA Monitor Height = Main
>> P3 = 30
>>
>> When ever I turn on the P3 (and monitor), I need to reset the Waterfall
>> Height.  The Height is fine on the P3, but takes up 3/4 of the screen on
>> the external monitor. The P3 remembers the original Height setting. To
>> reset the Waterfall Height on the external monitor, I need to go to the P3
>> Waterfall Height, make any change in the Height value, and then the
>> Waterfall Height on the external monitor corrects itself. Not sure why the
>> External Monitor requires this and if it has something to do with the
>> P3 SVGA board or a monitor setting?
>>
>> Thanks, Irwin KD3TB
>>
>>
>>
>>
>> --
>> Irwin KD3TB
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>> <javascript:_e(%7B%7D,'cvml','Elecraft@mailman.qth.net');>
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to k2av@gmail.com
>> <javascript:_e(%7B%7D,'cvml','k2av@gmail.com');>
>>
>
>

-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] SVGA/P3 Question -Waterfall Height Problem

[Irwin Darack]

I have a P3 with the SVGA board installed + an external monitor.

SVGA Monitor Height = Main
P3 = 30

When ever I turn on the P3 (and monitor), I need to reset the Waterfall
Height.  The Height is fine on the P3, but takes up 3/4 of the screen on
the external monitor. The P3 remembers the original Height setting. To
reset the Waterfall Height on the external monitor, I need to go to the P3
Waterfall Height, make any change in the Height value, and then the
Waterfall Height on the external monitor corrects itself. Not sure why the
External Monitor requires this and if it has something to do with the
P3 SVGA board or a monitor setting?

Thanks, Irwin KD3TB




-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] SVGA KPod Macro

[Irwin Darack]

I am looking for a set of macros for my KPod that turns on/off the SVGA
Data Terminal screen for CW receive in the P3 external monitor.
Any suggestions are appreciated.
Thanks, Irwin


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] k3s radio kit

[Irwin Darack]

I have build two this year. Each took a few days to complete, only spending
a few hours each day on the project.  I took over the dining room table,
with my wife's permission, spread everything out and check the inventory
before starting. All parts, especially screws, washers and nuts were sorted
and placed in separate small glass bowls. Before installing a screw, I
double checked the length and size with a good ruler, etc. The instructions
are extremely well written and easy to follow.  Just follow them closely
and always double check your work after each step. If you take your time,
are careful what you do, you really have the pleasure of building your own
radio.
Good luck,
Irwin, KD3TB

On Fri, Aug 5, 2016 at 10:14 AM, Wayne Burdick  wrote:

> Hi Wayne,
>
> Assembly is very straightforward, with very clear instructions, drawings,
> and photos in the manual. The best advice is to read instructions carefully
> and perform the steps in order.
>
> 73,
> Wayne
> N6KR
>
>
> On Aug 5, 2016, at 7:05 AM, Wayne Michael  wrote:
>
> > Any advise for a putting a K3S together?
> > I just ordered it.
> >
> >
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > Message delivered to n...@elecraft.com
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K-Pod

[Irwin Darack]

My K-Pod arrived on Monday and I am currently working on building Macros.

When I tap the F1 function key on the K-Pod it reads macro 09 on the K3S;
when I hold the F1 key, it reads macro 01 on the K3S. All the the function
keys seem to behaving the same. For example, tapping F4 = macro 12, while
holding F4 = macro 04.

When I write a macro using either SWT (tap function) or SWH (hold function)
for the K3S, and write to the K3S using the K3 Utility, the macro runs
correctly on the K3S.

Its just the Tap and Hold on the K-Pod seem to be reversed?  Should tapping
the F1 key on the K-Pod = macro 01 on the K3S, etc? Or was this how it was
designed? It seems to reversed from how the keys on the K3S and P3 behave.

Thanks, Irwin KD3TB



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K-Pod Questions

[Irwin Darack]

I just connected my K-Pod to my K3S  and have two quick questions:

1. When connected to my computer, what is the name of the Human Interface
Device?
I have a device showing up as FT232R USB UART?

2. I have a K3S with 12 VDC output (1 amp max powered switched) that I am
already using to power my P3. The P3 has the SVG Video card that I use for
an external display. Before connecting the K-Pod I want to make sure that I
will not be drawing more than the 1 am max.

Thanks,Irwin KD3TB



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] New Elecraft Product: K-Pod Control Panel for K3S and K3 Transceivers

[Irwin Darack]

Wayne,

Can you use the K-Pod function keys to key the CW, RTTY & DVK SSB memories
stored in the K3S?

Thanks, Irwin KD3TB

On Wednesday, April 13, 2016, Wayne Burdick  wrote:

> Hi all,
>
> We've had many requests for a small control panel (or pod) as an extension
> to the K3 and K3S transceivers. We finally got around to it!
>
> Our new K-Pod is a very compact unit, featuring a precision tuning knob,
> VFO A/B/offset rocker switch, and 8 programmable tactile-feedback switches.
> Switch feedback is provided by activation messages on the radio's LCD, as
> well as the pod's own 4 indicator LEDs and audio tone generator. This
> multi-modal information can help maximize operating efficiency and reduce
> fatigue during extended operating periods.
>
> Typically the K-Pod would be placed next to a computer keyboard, allowing
> the operator to quickly QSY, clear RIT, enter diversity mode, change menu
> settings, etc., without that long stretch to reach the radio's front panel.
>
> But the K-Pod's flexible interface goes beyond substitution of the radio's
> knobs and switches. In effect, you can design your own customized controls
> for the radio.
>
> Each of the 8 programmable switches has tap and hold functions. When a
> switch function is used, it activates one of up to 16 user-defined command
> sequences that are actually stored in the radio itself, as macros. A single
> macro can accomplish many tasks at once, such as setting up custom splits,
> configuring the receiver or subreceiver for specific situations, sending
> transmit messages at differing code speeds, etc. Macros can be easily
> created or edited using K3 Utility, which runs on PC, Mac, or Linux
> platforms.
>
> The K-Pod has the following features:
>
> * high-quality weighted, soft-touch tuning knob--same as used on the K3S
> * same 400-count, ball-bearing optical encoder used in the K3 and K3S
> * adjustable knob friction
> * 3-position rocker switch to assign the knob to VFO A, VFO B, or RIT/XIT
> * 8 programmable function switches, each with tap/hold functions
> * simple switch programming using K3 Utility (many examples in K-Pod
> manual)
> * four user-definable LEDs (three of them show knob assignment by default)
> * audio tone generator for switch feedback (can be easily turned off)
> * USB port for firmware loading and future equipment/computer control
> applications
> * simple connection to K3 or K3S--uses the 6-pin RJ-style jack beneath the
> front panel
> * flexible power source: rear 12-V jack on the radio, DC barrel jack,
>   USB port, or even through the 6-pin data cable, with minor radio
> modification
>   (the latter method results in a single cable to the K-Pod for data and
> power)
> * 3 utility outputs for miscellaneous equipment control applications
>   (outputs provide a low resistance to ground when turned on, usable with
> relays, etc.)
>
> The K-Pod's all-steel enclosure weighs a full pound for excellent
> stability, yet measures only about 3.5 x 3 x 1 inches. A highly stable
> folding tilt stand is included to angle the panel for optimal access.
> There's also a 2-hole RAM mount pattern on the bottom for easy attachment
> to any surface.
>
> For photos and further information, please visit our K-Pod web page:
>
>   http://www.elecraft.com/k-pod/k-pod.htm
>
> 73,
> Wayne, N6KR
> Eric, WA6HHQ
>
>
>
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com 
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] New K3S in the RTTY Contest

[Irwin Darack]

Ran a new K3S that I just built in the RTTY contest this weekend. Mostly
S with some minor runs. Kept the power to 70w. K3S fans never came on. If
they did, they were really quiet. Probably could have put the power
higher. Only the fan in my older P/S ocassionally came on. It was a good
way to break in the new radio and run it through its paces. Used the P3 to
find the stations and the CWT on the rig to fine tune them. Transmit
monitor let me keep an eye on my signal. Used a 400hz roofing filter to dig
out the close ones on a crowded band. Set the K3S to TX Data ( AFSK A -
LSB). For TX Data set the Mic Sel to Line in, no VOX. This let me use the
new USB Codec sound card and key the rig at the same time with N1MM+ and
MMTTY. Really pleased with the performance.

Irwin KD3TB


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3s pre-purchase question

[Irwin Darack]

Tom,

I just finished building my second K3S for my Beach House. The instructions
in the K3S assembly manual are excellent and very gratifying once you have
built it.  Just take your time. I only dedicated 3 hours each day to make
sure I did not make any mistakes.

I would go simple to start with. Given your antennas, you really want the
100 watt option.
K3S - 100w Kit, Digital Voice Recorder,  Auto Tuner, Filters - 400 Hz for
CW/ Digital,  and 2.1 and standard 2.7 kHz for SSB.  Unless you are really
into contesting, forget the second Receiver for now. You can always add it
later. That's all you need to get started.

I do not do much 2 meter operation, so I have not added that option.
Primarily I am on FM local repeaters. The same goes for the general
coverage option/filter.

Consider adding the P3 option in the future.

Good luck and enjoy the radio.

Irwin KD3TB



On Saturday, February 13, 2016, Tom Brohl  wrote:

> Hello Elecraft subscribers,
>
> I've been a ham for quite some time as a Technician class using
> 2-meter. I'm retired now with more time for my hobbies.
>
> I'll be taking my General class exam soon and moving on to HF.
>
> I've built many Heath kits in the day, so the Elecraft kits are striking my
> interest.
>
> I'm trying to configure a K3s kit and would sure like some help from you
> experienced hams.
>
> The up-front price is a lot for me so I'm trying to understand the
> necessities? With an upgrade path every 6 months or so.
>
> First, would I be disappointed with starting out with the 10-watt version?
> I
> imagine I'll be doing more listening in the beginning. But if 100-watts is
> important up front I'll get it.
>
> How about filter options? I'm guessing the standard filter will be ok to
> start out with?
>
> I may add the 2-meter option since my current radio needs replacing. If I
> do
> is the K144XV Reference Lock Board necessary for 2-meter operation?
>
> How about the KBPF3A General Coverage Receiver Filter?
>
> My antenna is a Cobra UltraLite Junior:  80-10 Meters 73 feet, installed in
> my attic. I also have an Astron VS35m Power Supply, Heil PR-781 mic,
> MFJ-993B Auto Tuner.
>
> Please recommend what options I should get with the K3s kit.
>
> Thanks for your help!
>
>
>
> -Tom
>
>
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com 
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] RTTY No Audio into K3S

[Irwin Darack]

I am in the process of setting up a second K3S that I just built and having
difficulties setting up RTTY using MMTTY

Using the USB Codec, I can key the rig, receive Audio in and copy RTTY, but
no Audio from the computer to the radio.

I have the correct speaker in the computer selected (USB Audio Codec) . In
the Config menu I show KIO3B and set to nor.

What am I missing - Not sure what to try next?

Thanks,

Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] RTTY No Audio into K3S

[Irwin Darack]

Thanks  to everyone. Simple Operator error. I forgot to set the mic to Lin
in for TX Data. That solved it.

Irwin KD3TB

On Friday, February 12, 2016, Bob McGraw K4TAX <rmcg...@blomand.net> wrote:

> You do have the speaker level at about 50% on the computer.  In the
> Windows 10 system I run,  I right click on the speaker symbol in the tray,
> then select Playback devices, then Speakers CODEC, the Properties then
> Levels.  The slider is sitting about mid scale or -10.2 dB or 50%.The
> radio is in Data A mode.   I set the MIC {actually Line level} to about
> 20.  This gets me 4 to 5 bars on the ALC scale.   Then set the PWR value
> for the number of watts you want out.
>
> Nothing is plugged in the rear panel audio connectors.  I only use the USB
> cable between the radio and computer.
>
> 73
> Bob, K4TAX
>
> On 2/12/2016 4:40 PM, Irwin Darack wrote:
>
>> I am in the process of setting up a second K3S that I just built and
>> having
>> difficulties setting up RTTY using MMTTY
>>
>> Using the USB Codec, I can key the rig, receive Audio in and copy RTTY,
>> but
>> no Audio from the computer to the radio.
>>
>> I have the correct speaker in the computer selected (USB Audio Codec) . In
>> the Config menu I show KIO3B and set to nor.
>>
>> What am I missing - Not sure what to try next?
>>
>> Thanks,
>>
>> Irwin KD3TB
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to rmcg...@blomand.net
>>
>>
>
>

-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KPA500 in RTTY Contesting

[Irwin Darack]

Thanks to everyone regarding their comments on the KPA500 and RTTY
contesting.

Irwin KD3TB

On Wednesday, January 27, 2016, Bob McGraw K4TAX 
wrote:

> OOPS .. I forgot my Periodic table.  Heat is  not an element. But the
> same thing applies.
>
> 73
> Bob, K4TAX
>
> On 1/27/2016 6:47 PM, Bob McGraw K4TAX wrote:
>
>> The most destructive element to all solid state devices is. HEAT!
>>
>> The KPA500 seems well protected and will drop off line if the temperature
>> exceeds a preset level.   My only concern regarding pushing an amp like
>> this or any other solid state amp to near rated values, same for near
>> maximum heat values, what happens if the protection circuit fails?
>>  Hopefully the software will recognize a protective circuit failure and
>> shut the amp down.
>>
>> 73
>> Bob, K4TAX
>>
>
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KPA500 in RTTY Contesting

[Irwin Darack]

I am curious to others experience with the KPA500 in a RTTY  Contest. What
 is the power level that others have used, fan levels and long term affect
on the power transistors?

I ask, as so far I have run the amp at no more than 300 watts with the fans
at there highest level. I do not want to harm the power transistors.

Thanks, Irwin KD3TB


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KPA500 finals blown

[Irwin Darack]

In discussions with Elecraft at Dayton, we should be able to run the KPA500
at 300 watts during a RTTY contest. This would include Running versus S/P.
The fans on mine do come on high and I keep an eye on the temp reading. I
do need to stop occasionally to allow the amp to cool down. I am not sure
if there is a way to add an addition external fan to increase the air flow?

Irwin KD3TB

On Thursday, January 21, 2016, Phil Wheeler  wrote:

> This in the specs in the KPA500 manual "Duty Cycle at 500 Watts 10 minutes
> key down / 5 minutes standby" seems pretty definitive for normal
> operations, even RTTY, Earl.
>
> 73, Phil W7OX
>
> On 1/21/16 6:44 AM, efortner wrote:
>
>> I would like to know what the continous keydown power output rating is.
>> The
>> manual talks about ICAS. I know when I get on RTTY I does not take long
>> for
>> The fans to come up to full speed running 300 watts.
>>
>> Earl, K4Kay
>>
>> -Original Message-
>> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
>> Nand
>> Kishore
>> Sent: Thursday, January 21, 2016 4:29 AM
>> To: elecraft
>> Subject: [Elecraft] KPA500 finals blown
>>
>> KPA500 shut off with a bang while operating RTTY @300W.
>>
>> Antenna is a steppir beam.
>>
>> On opening the KPA500,found 2 ceramic? caps of VRF2933
>> adrift with underside of the said caps,black.
>>
>> Have written to support.Is this the first time this has happened
>> in a KPA500?
>>
>> 73 and HNY,
>> Nandu
>> VU2NKS
>>
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3 Switching to 10W

[Irwin Darack]

In the RTTY contest, my K3 is turning off the 100W amp.

I set the FP Temp to 19C and the PA to Nor. I set the power to 60W output.
After contesting for a while, I would get a ERR=12V error and the rig would
shut off the 100W amp. The Circuit Breaker does not open.  I switched out
Power Cords to make sure one did not develop a short? The K3 Fans would
occasionally turn on so I know the fans are working.

My first thoughts are my Astron Switching Power Supply was starting to give
me problems. Its over 10 years old and maybe it can not keep up.

To test that, I will need to wait until I can replace with another Power
Supply.

Any other suggestions on what to look for?

Thanks,
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3 Fan Settings

[Irwin Darack]

How do I set the radio to turn on the fans when then 100 w amp temp gets to
a specific temperature.  I am playing around with the RTTY contest -
running 70 watts output into a tuned antenna.

With KPA3 set to NOR, the fans do not seem to turn on, even when the 100W
amp gets to high. I know the fans are working because when I set KPA3 to FN
1 to 4, then fans run continuously at the appropriate speed.

PA temp is set to 27C.  Should this be lower?

Thanks,
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 Fan Settings

[Irwin Darack]

Thanks. I will reset the PA Temp to a lower setting. I am finding that once
the PA temp gets to 27C, it shuts the 100w amp off and I only get 10W out
of the radio until it cools down. Even at 70W output in RTTY, I should be
able to keep the temp down with the fans? I am wondering if I have
something set wrong?

Irwin KD3TB

On Saturday, January 2, 2016, Don Wilhelm <w3...@embarqmail.com> wrote:

> Irwin,
>
> Yes, I think that PA Temp setting *may* be too high, but it 'all depends'.
> The PA Temp indication will follow the actual temperature of the heatsink,
> so if your K3 has been on for a while, that 27 degC may be normal.
> Follow the instructions in the manual to set the temperature.
> First turn off the K3 and leave it off until the heatsink acclimates to
> room temperature (at least 15 minutes, I recommend 30 minutes).
> Then turn it on and go to the PA TEMP menu - set it to the room
> temperature in degC.  For a 73 degF room, that would be 23 degC.
>
> If I recall, the fan will not turn on until the PA Temp reaches 40 degC.
>
> If you want the fan to come on sooner, set the PA Temp to a higher value.
>
> 73,
> Don W3FPR
>
> On 1/2/2016 4:55 PM, Irwin Darack wrote:
>
>> How do I set the radio to turn on the fans when then 100 w amp temp gets
>> to
>> a specific temperature.  I am playing around with the RTTY contest -
>> running 70 watts output into a tuned antenna.
>>
>> With KPA3 set to NOR, the fans do not seem to turn on, even when the 100W
>> amp gets to high. I know the fans are working because when I set KPA3 to
>> FN
>> 1 to 4, then fans run continuously at the appropriate speed.
>>
>> PA temp is set to 27C.  Should this be lower?
>>
>>
>>
>

-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Heil Proset Headphones

[Irwin Darack]

I am looking at picking up a second Headset Mic - DX chasing and
contesting.

What is the difference between the Heil Proset PS 6 and the Heil Proset K3
headsets for the K3 & K3S radios?

Happy New Year

Thanks, Irwin KD3TB


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX3 for sale

[Irwin Darack]

KX3 is sold.

Happy New Year to everyone.

Irwin KD3TB

On Monday, December 28, 2015, Irwin Darack <idar...@gmail.com> wrote:

> If Santa didn't bring you any good toys this holiday season, I have a KX3
> for sale:
>
> KX3 Transceiver
> KXAT3 Auto Tuner
> KXBC3 Internal Charger with Clock ( never installed)
> KXFL3 Roofing Filter
> MH3 Microphone
> KXUSB USB Interface
> KX3-2M AT 2 meter module with Auto Tuner
> KX3-PCKT Cable set
>
> Asking Price is $1,300.00 USD + Shipping and Insurance or Best Offer
>
> PayPal accepted ( if you use PayPal Purchase they add a 3% surcharge)
> CONT USA Only
> Non-Smoking Environment used as a second radio, lightly used, mint
> condition
>
> Irwin KD3TB
>
>
>
> --
> Irwin KD3TB
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KX3 for sale

[Irwin Darack]

If Santa didn't bring you any good toys this holiday season, I have a KX3
for sale:

KX3 Transceiver
KXAT3 Auto Tuner
KXBC3 Internal Charger with Clock ( never installed)
KXFL3 Roofing Filter
MH3 Microphone
KXUSB USB Interface
KX3-2M AT 2 meter module with Auto Tuner
KX3-PCKT Cable set

Asking Price is $1,300.00 USD + Shipping and Insurance or Best Offer

PayPal accepted ( if you use PayPal Purchase they add a 3% surcharge)
CONT USA Only
Non-Smoking Environment used as a second radio, lightly used, mint condition

Irwin KD3TB



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KIO3B

[Irwin Darack]

Thank you. Elecraft is a world leader in both workmanship and customer
service. They are true Hams designing and building products for Hams.

To them and everyone else on this reflector who truly help each other;
thank you and wishes for a warm and joyous holidays.

Irwin KD3TB

On Thursday, December 17, 2015, Jim Ewing  wrote:

> Regarding posts reflecting impatience with KIO3B deliveries, other
> displeasure:  I don't agree with you.  I have owned my K3 for about 2
> months, after researching matters fully and finally making my decision to
> buy.  As a benchmark, I also collect and operate Collins radios, which are
> works of art and evoke the character, talent, vision and elegance of Art
> Collins.  I love my K3 and greatly admire Elecraft for reasons that
> parallel why I love Collins radios and the legacy of Art Collins.  In at
> least these respects:
>
>
>
> 1.Elecraft are people who clearly build these radios as a labor
> of love.  They operate cw (sometimes during lunch break!), do QRP, hike and
> accordingly know what’s needed to build radios that are a joy to operate –
> even outdoors and on the trail where radios are put to the greatest test.
> They come from a long line of great radios, having built the NorCal 40 and
> the Sierra, among other great radios.  I can tell from the craftsmanship,
> design, attention to detail and ergonomics, that my K3 is a labor of love.
>
>
>
> 2.I admire their story.  I admire how Wayne Burdick left his
> day job to start this company, and how Eric also bet his assets on the
> venture as well.  They believe in and love what they do, and my K3 sitting
> in my shack always reminds me of that powerful story.  They are not
> beholden to the bankers who might encourage more massive production, corner
> cutting and expediency, next-Q profit mentality over quality.  They have
> the discipline to avoid spreading themselves too thin.  They have the
> courage to keep their focus on doing things well, even if that sometimes
> means we have to wait.  Sometimes, as here, good things come to people who
> wait.
>
>
>
> 3.Their manual is well written, well organized, cogent, and
> pleasing-to-read – some of the best technical prose I have ever read (this
> I can say after practicing telecoms patent law for 33 years).  The manual
> is not just some random listing of buttons and features like you see in
> other manufacturers’ manuals, but rather reflects the thought, care and
> organization of someone who has put himself or herself in the operator’s
> shoes.
>
>
>
> 4.As a builder, I appreciate the thought, competence and
> innovation reflected in how their circuits are designed, for maximum
> performance and reliability, and minimal power consumption.  I also think
> it’s great they don’t seem to feel compelled to hire a Jony Ive for the
> latest cosmetic design in order to sell radios.
>
>
>
> 5.Their customer support is orders of magnitude above everyone
> else.  The other night, for example, I sent an email about some error
> messages I was getting, and Elecraft responded with the correct fix early
> the next morning.  Turns out I had inadvertently, in boneheaded fashion,
> hit the Config button and changed a setting.  The level of care, tact and
> patience reflected in the email, on top of the raw technical competence,
> were not lost on me.
>
>
>
> 6.That said, I am doubly dismayed, saddened and annoyed when my
> reflector message list is fouled with the whining of people who seem blind
> to these great radios and this great company.  People who whine because
> they want whatever *right now *so they can dash off to their island without
> delay, who are cheesed because the knobs are not sufficiently shiny, who
> seem affronted by the notion of having to open their radio up to add some
> of the amazing boards and circuits offered by this best-of-planet company
> because it might mar the paint job.  I am reminded of that New Yorker
> cartoon some years ago that shows a Met Patron standing in front of a Monet
> and complaining, reflecting more on herself than on the artist.  Would you
> people please *just stop*?
>
>
>
> Thank you.
>
>
>
> Jim Ewing
>
> N4TMM
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com 



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: 

Re: [Elecraft] OT looking for K3EZ utility

[Irwin Darack]

Great Utility that I routinely use to check Config and Menu settings.
Possibly Elecraft can repost on its Download Web site. This software was
very helpful when I set up my new K3S and wanted to mirror setting from my
older K3.

Irwin KD3TB

On Thursday, December 10, 2015, Kjeld Holm  wrote:

> Hi Elecrafters
> I find the utility K3EZ very useful. Going to a new computer I searched the
> internet for a copy but did not find any.
> Can someone direct me to a download site?
> Best regards
> Vy 73 de OZ1CCM
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com 
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Elecraft Cable

[Irwin Darack]

Is the cable between the P3 and Directional Coupler for the transmit
monitor a ethernet lan cable? That way I can use a shorter cable?

Thanks, Irwin KD3TB


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Elecraft 1.8 Hz Roofing Filter for sale

[Irwin Darack]

I have a 1.8 Hz 8 pole Roofing Filter for K3 or K3S for sale. Purchased new
from Elecraft with my original K3. I replaced this filter with a 2.1 Hz for
SSB.

Asking $100 or Best Offer + free shipping in CON USA

Please contact me off list.

Irwin KD3TB




-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] having problems connecting my K-3 to Ham Radio Deluxe

[Irwin Darack]

I also run HRD with my K3S and K3 using Win 10 with no problems.
Irwin KD3TB

On Friday, November 6, 2015,  wrote:

> What issues are you experiencing? I'm running the latest HRD with Win 10
> and
> not having any issues. Are you running any type of port multiplexing
> software? I don't recall the name, however, one popular one definitely
> isn't
> stable on win10.
>
> Jerry Moore
> CDXA, INDEXA, SKCC, Fists
> AE4PB, K3S - S.N. 010324
> http://www.qrz.com/db/AE4PB
> An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and
> Patriotic.
>
>
> -Original Message-
> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net ]
> On Behalf Of Bob
> McGraw - K4TAX
> Sent: Friday, November 06, 2015 9:31 AM
> To: elecraft@mailman.qth.net 
> Subject: Re: [Elecraft] having problems connecting my K-3 to Ham Radio
> Deluxe
>
> I tried HRD 6.0 and dumped it.  I find there are issues with Windows 10 and
> HRD 6.0 that have not been resolved.
>
> I do run Windows 10 and other applications,  i.e.  HRD 5.0/DM-780, FLDIGI,
> WSJT-X and others very successfully with the K3S and the USB to radio
> connection.  So, if it runs with HRD 5.0 and not HRD 6.0, using the same
> computer, same operating system, same cable, same radio, I strongly suspect
> the issue is within HRD 6.0.
>
> 73
> Bob, K4TAX
> K3S s/n 10163
>
>
> On 11/6/2015 7:44 AM, John Weber wrote:
> > When I connect the radio thru the KUSB port to the computer and load
> > the HRD program
> >
> > I get a screen indicating that the program can not find the radio.
>
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message
> delivered to je...@carolinaheli.com 
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com 
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KXPA100 with KXAT100 for Sale

[Irwin Darack]

The KXPA100/KXAT100 has been sold.

Thanks to everyone who responded.

Irwin KD3TB

On Tuesday, November 3, 2015, KD3TB  wrote:

>
>
> PX3 Sold –  I Still have the KXPA100 (KX3 Amp) with KXAT100 (KX3 Tuner) &
> KXPACBL (Cable Set)  for sale
>
>
>
> Serial Number: 0067 - Factory Built: -  $975 (or best offer) +
> Shipping/Insurance
>
> Includes the Manual
>
>
>
> Non-smoking environment.
>
>
>
> CONUSA only, Payment by PayPal (Transfer of Funds) or Check. Will ship
> after check clears my bank.
>
>
>
> If interested, please contact me off list.
>
>
>
> Irwin  - KD3TB
>
>
>
>
>
>
>
>
>


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] PX3/P3SVGA Compatible USB Keyboard List

[Irwin Darack]

On Wednesday, October 14, 2015, Paul Saffren N6HZ 
wrote:

> With the release of PX3 BETA firmware 1.35, several customers have inquired
> about which USB keyboard are compatible with the PX3 and P3/SVGA.  Here's a
> short list of keyboards several customers and I have tested.  (see below)
> If you're using a keyboard that is not on this list, please email me
> directly and include the make and model if possible.  (pauls at you know
> where dot com)
>
> 73 and thanks,
>
> Paul
>
> -
>
> PX3 suggested keyboard list
> © 2015 Elecraft Inc
> Keyboards listed were available when this list was created and have been
> tested with the PX3/P3SVGA
>
> Note: most "PC BIOS compatible" keyboards will work.  In other words, the
> keyboard must be able to be recognized by the PC BIOS.  This
> rules out Bluetooth and multimedia style keyboards, those with mice,
> touchpads, and multimedia functions.
>
>
>
> Model NumberManufacturerStyle/Notes
>
> K360LogitechWireless
> K270LogitechWireless, separate keypad
> K120LogitechWired
> KB212   Dellwired, full size, came with PC
> Monoprice Flexible  Monoprice   Wired, available on Ebay
> MK360   Logitechwireless, inludes mouse
> KU-1060 HP  wired, full size, came with PC
> SK-2085 HP  wired, full size , came with PC
> KB113p  Dellwired, med size, came with PC
>
> "78 Key USB Slim Mini Small Thin Keyboard Compact Desktop Laptop PC Win 7
> White"  Ebay
>
>
>
>
> --
> View this message in context:
> http://elecraft.365791.n2.nabble.com/PX3-P3SVGA-Compatible-USB-Keyboard-List-tp7609061.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net 
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to idar...@gmail.com 



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3S Extenal Stereo Speakers

[Irwin Darack]

A speaker volume question.

My set up:  I have a pair of Polk miniature (non powered) stereo speakers
plugged into my K3S.  I plug my headphones into the front connector and
have the Config menu set up so that if the headphones are plugged in, no
sound comes from the stereo speakers.

I find that the volume in the headphones is much higher than the stereo
speakers when the AF audio is the same.  I am wondering if there is a
setting in either the Menu or Config settings to equalize this or adjust
for the difference without having to constantly adjust the AF setting?

Finally, it could just be that I need to find a better set of stereo
speakers? any recommendations?

Thanks,

Irwin KD3TB



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Panadapter

[Irwin Darack]

I have both the P3 for my K3 station ( main station) and PX3 for my KX3
station ( beach house station). And think they are an excellent addition
for both contesting and chasing DX in a pileup.

Irwin KD3TB

On Monday, January 26, 2015, Mark Tellez aar...@gmail.com wrote:

 Hello all,

 I would like to know what people think of the new Panadapter.  I am
 considering adding it to my portable station.  I would like to know what
 people think of its features and the usefulness (and drawbacks) in a
 portable configuration.

 Thanks,



 Mark
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to idar...@gmail.com javascript:;



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KXPA100 Loosing Communications/ Turns PA Mode Off

[Irwin Darack]

I recently checked and upgraded all of the Firmware with my KX3 (MCU =
2.27,  DSP = 1.3), KXPA (1.32) and PX3 (1.16) that was older.

I found that  it lost communications from the KX3 to the KXPA100. Hence it
results in turning PA Mode Off. Even when I go back into the Menu settings,
turn PA Mode on again, It results in turning PA Mode back off again.

Even though I had full communications between the KX3 and KXPA100, to
resolve the problem, I had to going into the utility program for the PX3,
making sure it was communication with my computer, which it was, then
update the KX3 Menu PA Mode to on.

I am not sure where the glitch is occurring. I have the standard cable set
up as in the PX3 Manual and all data rates are set to 38400 baud. It seems
to be related to the PX3.

Is there a way to extend the time out for the KXPA100?

Thanks, Irwin

-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KX3 2 Meter Module SWR tolerance

[Irwin Darack]

Has anyone determined the SWR tolerance to the KX3 2 Meter module before
folding back or giving a high SWR error.  I am wondering when in the FM
mode, it will work with common Dual band mag mount antennas?

Thanks, Irwin KD3TB


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] OT K3/KX3 and Raspberry Pi

[Irwin Darack]

There is a small group of us who have our Rasberry Pi's hooked into a Dvap
for D-Star.

Irwin, KD3TB

On Tuesday, December 30, 2014, James Bennett w6...@me.com wrote:

 Just wondering if any folks on this reflector have been using the
 Raspberry Pi (RPI) computer with their rigs or any other ham-related
 stuff?

 I got one for my Jr op (6 yrs old) several months ago and he has only used
 it occasionally. I'd like to integrate it into my ham shack where it
 might get more use. Right now my K3 and KX3 are tethered to an iMac which
 works quite well. Not looking to replace the iMac - just thinking about the
 RPI in the shack.

 Jim Bennett / W6JHB
 Folsom, CA
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to idar...@gmail.com javascript:;



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KX3 and KXPA100 loosing connection

[Irwin Darack]

My KX3 and KXPA100 lost connection when I was changing one of the DVR's in
the KX3. This also happened when I recently updated the Firmware and I had
to reset the settings in the KX3.

During the ARRL SS Contest, I went to change Memory 2 and found that the
KX3 lost the connection to the KXPA100. The KX3 changed the PA Mode setting
from on to off? I had to reset them.

My station set up is the PX3, KX3 and KXPA100. This never happened before
during a contest and I am wondering if it has something to do how the
passing of information through the PX3 first and then to the KX3, KXPA100?

I have no problems with passing frequency information and macro's to key
the KX3 memories in the contest.
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] KXPA100 Firmware upgrade

[Irwin Darack]

In preparation for the upcoming ARRL Sweepstakes, I checked the firmware
versions for my KX3, KXPA100  PX3. The only one that need to be upgraded
was the KXPA100. After doing this, the KX3 would no longer recognize the
KXPA100. I had to go back into the KX3 menu settings and reconfigure it for
the KXPA100?

This is the first time I have seen this happen, were the firmware upgrade
on the KXPA100 changes the settings in the KX3.

Must be the ghost of contesting past having fun with me!

Irwin KD3TB


-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Ham Radio Deluxe and KX3 Radio

[Irwin Darack]

I have been configuring HRD with my KX3 and wondering if anyone else has
done so?

I can get HRD to copy and send PSK31 and RTTY with the KX3 in Data A (rev)
mode. Although I can copy CW, HRD will not key the KX3 for CW

I have tried multiple setting in the KX3 and HRD.

Has anyone been able to get CW to work with HRD?

Thanks,
-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KPA500 in the RTTY Contest

[Irwin Darack]

Great testimonial on Elecraft quality and the KPA500

Irwin, KD3TB

On Monday, September 30, 2013, KD3TB wrote:

 For General Information - 

 ** **

 I ran the KPA500 in the CQWW RTTY contest this weekend.  With a drive
 power of 15 to 20W from the K3, I kept the KPA500 output between 350 and
 400W output.  Even during runs (calling CQ), the temperature never went
 above 65 degrees on the KAT500 meter. The cooling fan changed speeds as
 needed and kept the amp with its tolerances. This was enough power to break
 pile ups and get into Asia with no trouble.  The interface between the
 KAT500 and KPA500 was seem less allowing me to quickly move between bands.
  Although not listed as a RTTY contesting amp, I was really impressed with
 the KPA500 performance. 

 ** **

 Irwin - KD3TB

 ** **



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KPA-500 in Contest Conditions

[Irwin Darack]

We use the KPA500 and KAT500 combination at our VE2DXY contesting station
in zone 2 for CQWW SSB contest. The combination makes an excellent
contesting setup. I have also used in other CW, SSB  RTTY contests and
very impressed with The performance. I really like its ability to rapidly
change bands with out having to tune an amp. Much different than my older
tube amp.

Irwin, KD3TB

On Friday, July 12, 2013, Mark Stennett wrote:

 We used several KPA-500 amplifiers on the Swains Island NH8S DXpedition and
 they performed flawlessly under  24/7 use for 9 days straight in hot and
 humid tent conditions.
 -Original Message-
 From: Richard Thorne rtho...@rthorne.net javascript:;
 To: Elecraft Reflector elecraft@mailman.qth.net javascript:;
 Date: Fri, 12 Jul 2013 08:48:52 -0500
 Subject: [Elecraft] KPA-500 in Contest Conditions


 Hows the KPA-500 holding up under contest conditions for SSB and CW?

 I've read the reviews on eham but there was only one that referenced
 performance in contest conditions (and it was favorable).

 I'm curious if the temp stays down and if power is lost as it heats up?

 Thanks

 Rich - N5ZC

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 [http://mailman.qth.net/mailman/listinfo/elecraft]
 Help: http://mailman.qth.net/mmfaq.htm [http://mailman.qth.net/mmfaq.htm]
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net [http://www.qsl.net/]
 Please help support this email list: http://www.qsl.net/donate.html
 [http://www.qsl.net/donate.html]
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KPA500

[Irwin Darack]

I would be interested if Elecraft has any recommendations on their
experience. I have used the KPA500 in one RTTY Contest at around 350w. When
in a Run Mode (CQ'ing) the amp heats up pretty fast and the fan runs at a
high speed continuously.

Thanks, Irwin KD3TB

On Sunday, June 23, 2013, wrote:

 On Sun, 23 Jun 2013 11:33:53 +0200, Arie Kleingeld PA3A wrote:

  Running 330W output in RTTY, 50% duty cycle.
  SWR is OK: 1 : 1.1 or so.
  Ambiant temp = 25C
 
  Fan runs at speed 4, occasionally 5
  PA TMP hovers between 65 and 70 C

 I'm guessing would be fairly normal.  I sure wouldn't run it that heavy on
 a 50%
 duty-cycle operation (even if the factory says you can).  I just don't like
 running things hot.  Mine hits full 747 turbine mode pretty easily.

 Gary
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 , KPA500, KPA500 interaction.

[Irwin Darack]

Andy  Ken,

What is your experience here?

Irwin

On Saturday, March 16, 2013, Dick Dievendorff wrote:

 As others have said, the mechanism the KAT500 uses to inhibit the
 amplifier is the amplifier key line, sometimes labeled PTT. The KAT500
 manual shows cabling diagrams that cause the K3 key line to go thru a relay
 in the KAT50o to the amp.  The amp doesn't change to standby, it is simply
 not keyed and therefore does not amplify during ATU tuning operations.

 73 de Dick, K6KR

 On Mar 16, 2013, at 6:17 PM, Bill Wiehe bw39...@yahoo.com javascript:;
 wrote:

 
 
  As a follow up the recent information passed along on the subject under
 another thread (* on KPA500) I am looking for some additional
 clarification. I was under the impression that
  KPA500 would go into standby automatically when the KAT500 went into a
 tune mode.
  Apparently this is not the case unless I have something set wrong. I
 have found
  when changing bands if I initiate the K3 “tune cycle” the KPA500 will
 not go into
  standby.The KPA500 goes in and out of transmit mode and eventually will
 go into a soft fault if there is an initially high (SWR) while the KAT500
 continues to look for a match. The fault due to high reflected power of
 course is as it should be and must be cleared to proceed. Just curious but
 is this correct expectation or is there a
  set up function I missed that automatically places the KPA500 in standby
  when the   As I said I was under the impression that whenever
  the KAT500 did a tune the KAP500 would go into standby.
  This is not a major problem as I have set up the KPA500 now
  to go to standby whenever I change bands as well as initial start-up. I
 am still curious however if I missed something.
  Thanks
 
  Bill – W0BBI
  __
  Elecraft mailing list
  Home: http://mailman.qth.net/mailman/listinfo/elecraft
  Help: http://mailman.qth.net/mmfaq.htm
  Post: mailto:Elecraft@mailman.qth.net javascript:;
 
  This list hosted by: http://www.qsl.net
  Please help support this email list: http://www.qsl.net/donate.html
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3 and KPA500

[Irwin Darack]

Please share your solution as I plan on powering the KPA500 with a KX3 too

Thanks, KD3TB

On Sunday, June 10, 2012, Adrian wrote:

 ACC2 IO setting  LO=PTT (input; apply 0 V or ground to

 activate PTT)



  I can't figure out how to set the ACC2IO on the KX3 so that it will key
 the KPA500 properly. I currently have the ACC2IO in the off position. When
 I connect the cable between the ACC2IO and the PA Key on the back of the
 KPA500 it puts the KPA500 in a transmit mode. I have to manually put the
 KPA500 in standby to receive and then Operate to transmit. I have tried a
 number of different settings on the KX3 and KPA500 with no success.  What
 am
 I doing wrong?  (incidentally the KX3 will drive the KPA500 to almost 200
 watts output).



 Dave WA6DKN







 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] ARRL CW DX Contest

[Irwin Darack]

Same here. Ran the K3 and P3 with a G5RV from my beach house. Great fun and
a great CW combo!

KD3TB

On Sunday, February 19, 2012, Bruce Chadbourne wrote:

 Just had to say - I had a blast with my K3 in this weekend's contest - I'm
 not one to lead the pack, but surpassed my expectations and set a
 respectable score I'll shoot to exceed next year.  A lot of high power rigs
 out there and the K3 got a lot of respect running 100 watts (G5RV antenna).

 All of the K3/P3 features got a good workout - I gained code speed and
 operating proficiency. Thank you Elecraft!

 --
 Bruce Chadbourne KE1CY
 Merrimack NH
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net javascript:;

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html



-- 
Irwin KD3TB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html