Kind of worried based on
http://www.cisco.com/c/en/us/products/collateral/routers/3900-series-integra
ted-services-routers-isr/guide_c07-726864.html that I'm also going to have
to buy:
ISR4430U-MEM-SSD
DRAM upgrade to 16GB, Flash Memory upgrade to 16GB, NIM Carrier and 200GB
SSD Bundle
Hey guys,
If I need a router that can do application based bandwidth throttling
(NBAR2) at 500M-1G aggregate throughput, ISR4431-AX/K9 should do the trick,
right? It seems to provide the features and throughput. Please tell me if
I'm wrong (other services enabled on the router will be limited
Hello,
If you hve SNMP write access, you can push a config file to your router
with the access-list you want to create or modify. The config file could be
dowloaded by the router via TFTP.
We have similar command on the Brocade side, not the cisco side and have had no
issues:
interface Port-channel 3
description L2 Transit to Cisco-Kit
no ip address
portmode hybrid
switchport
no spanning-tree pvst err-dis cause invalid-pvst-bpdu
no shutdown
-Original Message-
From:
Yes, I was very surprised. We are rolling out some Brocade ICX 7k units. If
you LACP one of those to a Cisco, this will happen. I have observed it with
ICX 7750 and 7450, as well as Catalyst 3850 and 6700.
On Tuesday, July 12, 2016, Gert Doering wrote:
> Hi,
>
> On Tue, Jul
Hi,
On Tue, Jul 12, 2016 at 02:26:36PM -0500, Hunter Fuller wrote:
> If you are running a LACP bundle, and the other end is not a Cisco
> piece of gear, and the error only happens when more than one link is
> up, then what is happening is, the far end is sending BPDUs on more
> than one member of
Hi,
On Tue, Jul 12, 2016 at 08:41:57PM +0200, Olivier CALVANO wrote:
> there is a solution to disable the errdisable on this type of switch?
Fix the difference in config between the ports, so there is no
inconsistency any more?
gert
--
USENET is *not* the non-clickable part of WWW!
If you are running a LACP bundle, and the other end is not a Cisco
piece of gear, and the error only happens when more than one link is
up, then what is happening is, the far end is sending BPDUs on more
than one member of the LACP bundle. Cisco gear does not expect this
and will shut the entire
Read this -
http://www.cisco.com/c/en/us/support/docs/lan-switching/spanning-tree-protocol/69980-errdisable-recovery.html
However - as alan said - it is more important to figure out why this is
happening - than to have it recover automatically.
Are you making configuration changes to the
Hi,
> Jul 12 17:30:36.218: %PM-4-ERR_DISABLE: channel-misconfig error detected on
> Gi1/0/1, putting Gi1/0/1 in err-disable state
so...what is the cause of this. check the config of gi1/0/1, ensure it matches
the methods/speed etc of other members of the port-channel etc its been
assigned to
Hi
i have a big problems with one cisco 3750 :
Jul 12 17:30:36.218: %PM-4-ERR_DISABLE: channel-misconfig error detected on
Gi1/0/1, putting Gi1/0/1 in err-disable state
Jul 12 17:30:36.856: %PM-4-ERR_DISABLE: channel-misconfig error detected on
Po1, putting Gi1/0/1 in err-disable state
Jul 12
On 07/12/2016 07:29 AM, Mark Tinka wrote:
What licenses is it running?
AdvancedMetroIP.
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
On 12/Jul/16 16:10, Mike wrote:
>
> Damm. Yes, I am running 15.4(3)S2 on this box at the moment, and yes
> it's an ATT metro-ethernet product I am attached to. I just don't
> understand - it sure as hell seems that when I tested using my own
> network, putting an IP directly on the port (with
On 07/12/2016 04:06 AM, James Bensley wrote:
Hi Mike,
You haven't mention what IOS/IOS-XE versions you are using.
Is this a 3rd party fibre/wavelength/pseudowire by any change, if so
have you raised this with the carrier?
Damm. Yes, I am running 15.4(3)S2 on this box at the moment, and yes
Check the below link , it might help you
https://supportforums.cisco.com/discussion/10732136/snmp-modify-or-add-acl
BR,
Mohammad
> Date: Tue, 12 Jul 2016 15:37:37 +0300
> From: ro...@kharkov.org.ua
> To: cisco-nsp@puck.nether.net
> Subject: [c-nsp] Modify access list via SNMP
>
> Hi,
>
> We
Hi,
We have ASR 1002 and i want modify access list (add\remove entries)
via SNMP, this is possible yet? Can someone show me links where i can
get info about this. If you have some examples this will be good also.
Thanks.
Regards,
___
cisco-nsp
Hi Mike,
You haven't mention what IOS/IOS-XE versions you are using.
Is this a 3rd party fibre/wavelength/pseudowire by any change, if so
have you raised this with the carrier?
Cheers,
James.
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
Hi,
I have a damm weird one.
I have an me3600x, and gi0/7 is a fiber port. I have configured it
thusly:
interface GigabitEthernet0/7
no switchport
ip address 10.0.16.129 255.255.255.248
speed nonegotiate
Another device (an asr920) on the other end of that fiber
18 matches
Mail list logo