Re: [Elecraft] KX3 Time Out Timer

I am running WSIT-X, but anything on the computer that could activate the VOX, PTT, or CW key line could cause the KX3 to hang in transmit on a variety of modes. I only run 500mw on WSPR so the PA Hi Temp Limit should not be relied on to stop transmission. It would be nice if the KX3 had a

Re: [Elecraft] Using N1MM to Key a K3 with no outboard keyer

I have a project on my website ( NR4C.net/projects ) that will connect to a serial port (DE-9 or KUSB) and provide the CAT and breakout DTR & RTS lines for CW and PTT on KX2 and KX3 radios. Works well with n1mm. Sent from my iPhone ...nr4c. bill > On Aug 1, 2018, at 9:08 PM, Richard Ferch

Re: [Elecraft] K3s+KPA500 SSB Audio Distortion

To be sure, your next test is to run the KPA500 into a dummy load and listen to yourself on another receiver. This will help confirm if you have an equipment issue or an RFI issue. It is critical to start with a very basic setup and work your way up to more complicated. K3 and a hand mic into

[Elecraft] K3s+KPA500 SSB Audio Distortion

Michael I also have the same problem. Worked on it with Elecraft Support several times to no avail. I have tried several different microphones, antennas, baluns. Still no joy. I also use 18 watts drive, I had not thought of anything other than rf feedback. I will play with different drive

[Elecraft] FS: N-Gen Module

For Sale: N-Gen Wide Band Noise Generator $50.00 PayPal OK Lee Buller K0WA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net

Re: [Elecraft] K3s+KPA500 SSB audio distortion

Bruce, Elecraft is replacing mine too. They came to that conclusion after directing me to make a few tests and report the results. 73 - Mike - K9JRI > On Aug 1, 2018, at 20:54, "k...@comcast.net" wrote: > > A local ham had the exact same problem. It was not a problem with his setup. >

Re: [Elecraft] Using N1MM to Key a K3 with no outboard keyer

This works but it is far easier. If you are using the built-in Meyer in the K3, just go to CONFIG/PTT-KEY and set to “off-DTR”. Now go the n1mm config and set your radio comm port and check “cw” and then tap “Set”. Setup the port info and under DTR set to CW. Close the configurer window and

Re: [Elecraft] K3s+KPA500 SSB audio distortion

If the problem is present with the K3 (without the KPA500) set to 50 to 100 watts, then the KPA3 is the likely problem. BUT if the K3 operated up to 100 watts does no have the problem, look for an RF in the Shack problem that may not be apparent at 100 watts, but 'rears its ugly head' at 500

Re: [Elecraft] Using N1MM to Key a K3 with no outboard keyer

This keying method is not described in detail in the N1MM+ documentation because it is not supported by the N1MM+ development team. The reasons for this can be found in the N1MM+ online manual (at <

Re: [Elecraft] KPA-1500 Power Supply Cable Size

In other words! Keep It Simple Stupid! .KISS! Milverton / W9MMS. On Wednesday, August 1, 2018, 7:49:36 PM CDT, K9MA wrote: If one is going to remote the KPA1500, wouldn't it make a lot more sense to extend the 240 V AC line? Or just install a 240 V outlet at the

Re: [Elecraft] K2 KBT2 option question

Mark, The switch disconnects the K2 power input from the battery, so you must have the switch in the ON position for the battery to be in circuit for testing/operation (also for charging the battery). If you are using the power supply for charging the internal battery, increase the power

Re: [Elecraft] K3s+KPA500 SSB audio distortion

A local ham had the exact same problem. It was not a problem with his setup.  Elecraft replaced the PA board and the problem went away.BruceKS4V Original message From: Jim Miller Date: 8/1/18 10:42 AM (GMT-06:00) To: Ignacy Cc: elecraft@mailman.qth.net Subject: Re:

Re: [Elecraft] Using N1MM to Key a K3 with no outboard keyer

Ted and all, I believe you do need the CATA1ASC to send ASCII strings to the transceiver for keying (not PTT) for CW keying. The K3 with VOX set ON will key (and transmit CW) without asserting PTT. It is like "touch the key to transmit". Yes, other methods such as keying via DTR or RTS are

Re: [Elecraft] KPA-1500 Power Supply Cable Size

If one is going to remote the KPA1500, wouldn't it make a lot more sense to extend the 240 V AC line? Or just install a 240 V outlet at the amplifier location. 73, Scott K9MA On 8/1/2018 16:17, j...@kk9a.com wrote: That is why I said "IF" you are making a longer cable... John KK9A David

Re: [Elecraft] Using N1MM to Key a K3 with no outboard keyer

You do not need the "CATA1ASC " commands to key the K3/K3s via the CAT control link. Look here: The K3 can accept PTT switching from several sources, including: a keying circuit from a serial

Re: [Elecraft] Using N1MM to Key a K3 with no outboard keyer

Ted, That is something in N1MM which effectively tell the N1MM software to send the ASCII string which follows through the CAT port. You may find more information in the N1MM help file or forums. 73, Don W3FPR On 8/1/2018 7:32 PM, Dauer, Edward wrote: The following may test our commitment

[Elecraft] Using N1MM to Key a K3 with no outboard keyer

The following may test our commitment to the idea that there is no such thing as a stupid question . . . . I finally got around to setting up my N1MM logger to key my transmitters without having to use a K1EL or any other keyer -- just the KUSB cable directly from the PC into the rig. After

Re: [Elecraft] FS: Elecraft K3/100, power supply, cables...

SOLD __ Clay Autery, KY5G (318) 518-1389 On 01-Aug-18 10:53, Clay Autery wrote: I am re-listing the following for, and with the authority of Carl Beck, W5BEK: *** Elecraft K3 Transceiver (Serial #5765) as specified below *** PLUS: Adding the PowerWerx SS-30DV power

Re: [Elecraft] Remote Panadaptor : Question on K3 i-f buffer amps...

Gerry, Was your K3 purchased before about 9/1/2009? If so, it may not have the IF buffer mod installed which increases the gain at the IF output by about 10dB. See IF Output Buffer Gain Modification in the listing of K3 mods. 73, Don W3FPR On 8/1/2018 3:14 PM, Gerry Hull wrote: Hello

Re: [Elecraft] K3s+KPA500 SSB audio distortion

Elecraft tech support suspects a bad KPA3A and has arranged for a module swap. It is nice that you (me) can be so pleased even when you encounter a problem. Great company. Very 73 - Mike - K9JRI > On Aug 1, 2018, at 10:19 AM, Michael Blake wrote: > > While on the air on 3710 SSB I

[Elecraft] Pig Knob for Sale

I purchased a Pig Knob remote control for my K3 just before the K-Pod was announced. Great timing, eh? It has about one hour of use time on it - just enough for me to be sure it worked. I don't recall but I think I never programmed it for any specific function, so it probably still has the

Re: [Elecraft] KPA-1500 Power Supply Cable Size

On 8/1/2018 12:44 PM, j...@kk9a.com wrote: eventually I purchased a crimper and connectors and made cables myself. Call me old-fashioned, but I've installed hundreds of Power Pole connectors mostly the smaller red/white ones used on the K3, but also the much larger grey ones that accommodate

[Elecraft] KPA-1500 Power Supply Cable Size

That is why I said "IF" you are making a longer cable... John KK9A David Bunte K9FN wrote: I am also a bit confused (not the first time), but I could have SWORN that the initial query was from someone who wanted a SHORTER cable. Dave - K9FN On Wed, Aug 1, 2018 at 3:45 PM john at kk9a.com

Re: [Elecraft] KPA-1500 Power Supply Cable Size

I am also a bit confused (not the first time), but I could have SWORN that the initial query was from someone who wanted a SHORTER cable. Dave - K9FN On Wed, Aug 1, 2018 at 3:45 PM j...@kk9a.com wrote: > Elecraft was my first experience with power pole connectors and I have > purchased custom

Re: [Elecraft] KPA-1500 Power Supply Cable Size

WHICH is why I detailed in the VERY beginning on this thread how to make the longer cable using 4AWG (or larger if desired).  The ONLY place the cable would not be the larger gauge would be in the crimp terminal... IF anyone is interested, I will repost what I wrote  or just email me

[Elecraft] KPA-1500 Power Supply Cable Size

Elecraft was my first experience with power pole connectors and I have purchased custom cables from Powerwerx. They did a nice job, eventually I purchased a crimper and connectors and made cables myself. If you are making the KPA1500 cable longer than the factory cable it is probably desirable to

Re: [Elecraft] KPA-1500 Power Supply Cable Size

I'm missing something here!I keep seeing the question being asked, " What size cable is the power cord?" How about employing the KISS theory. Would it not make sense to make up an extension cord with a length to the approximate desired location from the power source? Such an extension would

[Elecraft] Remote Panadaptor : Question on K3 i-f buffer amps...

Hello All, I have worked with Tom, N1MM ad we now have a running remote spectrum window running. It's an AirSpy HF + at the station and a copy of N1MM+ which is forwarding the XML spectral data. Using this mode, it only uses about 6 kb/s for spectrum display and works VFB over a very limited DSL

Re: [Elecraft] KPA-1500 Power Supply Cable Size

Mike, I went directly to Elecraft with my question. The answer is 6g. I was told to be sure to use the correct crimp tool for the job.  If I make the cable I'll probably just have Powerwerx handle it as they have the correct hydraulic tool for the job. Rich - N5ZC On 8/1/2018 12:56 PM,

Re: [Elecraft] K3s+KPA500 SSB audio distortion

How are they connected? (i.e. are you using the AuxIO cable?) Do you have ALC turned on in the K3? 73! Jack, W6FB > On Aug 1, 2018, at 7:19 AM, Michael Blake via Elecraft > wrote: > > While on the air on 3710 SSB I receive audio reports that say my transmitted > audio is somewhat muffled or

Re: [Elecraft] KPA-1500 Power Supply Cable Size

Okay have looked over the posts, but somehow have missed the actual AWG(American wire gage) SIZE of the stock DC pair?   Anyone KNOW this or maybe even micro-ohm tested (a long shot) it?  Voltage drop (ps to amp) divided by full load dc amps would be close enough.  73,  Mike  AC5P  On

Re: [Elecraft] KX3 Time Out Timer

This is always a good idea. It should be on all of the radios.. 73 Tom  Sent from my Samsung Galaxy smartphone. Original message From: rich hurd WC3T Date: 2018-08-01 12:00 PM (GMT-05:00) To: George Pasek Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] KX3 Time Out

Re: [Elecraft] KX3 Time Out Timer

WSJT-X has a watchdog. Of course that's only useful if that's what you are running. :) On Wed, Aug 1, 2018 at 10:20 George Pasek wrote: > Maybe I was asleep in class the day this was discussed, but is there a TOT > for the KX3 transmitter? Now that I am running my KX3 a lot on WSPR I was >

[Elecraft] Elecraft Equipment for sale

Update The PX3 has been sold. The KX3 is still available. I’m flexible on a fair price. awinger2...@icloud.com 73 Al W1NGA Monument, CO __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] FS: Elecraft K3/100, power supply, cables...

I am re-listing the following for, and with the authority of Carl Beck, W5BEK: *** Elecraft K3 Transceiver (Serial #5765) as specified below *** PLUS: Adding the PowerWerx SS-30DV power supply to the deal!! PLUS: 2 each UHF to UHF jumpers (Belden 8214 cable stock 11 AWG)) (K3 to amp and amp

Re: [Elecraft] K3s+KPA500 SSB audio distortion

I ran my KPA500 for several years at 500w and often received unsolicited “great audio” reports. CM500 was my headset. Something is wrong with your setup. Jim ab3cv (have kpa1500 now) On Aug 1, 2018, at 11:09 AM, Ignacy wrote: Could it be RF feedback? You can check it by transmitting into a

[Elecraft] KX3 and PX3 combo for sale

I have just listed a KX3 and PX3 combo on eBay. Loaded with options and third party accessories. All are in excellent working conditions. Please see the list #123281700018.AH6CY Sent from Yahoo Mail for iPhone __ Elecraft mailing list

[Elecraft] KX3 Time Out Timer

Maybe I was asleep in class the day this was discussed, but is there a TOT for the KX3 transmitter? Now that I am running my KX3 a lot on WSPR I was thinking that it would be a good idea to have a TOT that would shut down the transmitter if a computer failure should keep the VOX or PTT active

Re: [Elecraft] K3s+KPA500 SSB audio distortion

Could it be RF feedback? You can check it by transmitting into a dummy load or lowering the drive power. Ignacy, NO9E -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

[Elecraft] K3s+KPA500 SSB audio distortion

While on the air on 3710 SSB I receive audio reports that say my transmitted audio is somewhat muffled or nasal. Making adjustments to mic gain, compression levels, TX EQ seems to make no difference to this report. These adjustments do change the sound of the audio but do not reduce the

[Elecraft] blocking

Yeh, tks for the snappy replies, fellas. I've had this intermittent blocked-post problem for years now, on this site only. One time it blocks, next time my posts go through. Some sort of arcanum, minutia, or trivium in the software that may require serious effort to find and fix.

[Elecraft] KPA1500 Remote Software Update

>"The link will be back soon. We found a few bugs in the remote sw and temporarily pulled it from the ftp site. Stay tuned! We'll announce here when it is back up next week. Eric /elecraft.com/" Any further updates on when the KPA1500 Remote Software will become available for download?

Re: [Elecraft] Speakers for KX3

Grant, thank for info about the Small Dog. I used them for few days when my friend visited me over here and they worked perfectly. Nice and smooth audio. Unfortunately no way to purchase them at Small Dog from EU as it will raise up to almost $60 including s/h from them... :( - 73 -

[Elecraft] test for blocking

test for blocking - Brgds, Dave, N3HE Cincinnati OH -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] FS: K3/0, cables

Hi, all concerned: FS: K3/0 sn 00xx. Excellent working order and physical shape. Unit is now surplus to needs. I _may_ have some of the cables for connecting a K3 to the Remoterig control unit, but definitely not the 12v-1A wall wart. Look at the Elecraft site info and tell me _exactly_ which