Hello Geert,
I guess the VFO-B knob for the K3S will fit, doesn't it?
The K3S is still available. Most probably available with a different part
number.
Just verify if the diameter of the ax K3 vs K3s is the same.
73's, Evert PA2KW / 5T2KW
-Oorspronkelijk bericht-
Van:
A Q abt the KRC2:
Is it possible two switch to two different antennes within one band but
based on frequency span ?
Example:
3.500 - 3.650 Mc Antenna 1
3.650 - 3.800 Mc Antenne 2
73's, Evert PA2KW
__
Elecraft mailing list
Home:
We all now (i guess) that decoding below the noise floor needs:
Time, timing and repetition..
no formulas needed .
73's, Evert PA2KW
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net]
Namens Joe Subich, W4TV
Verzonden:
Hello,
Haven been using my K3 in combi with the Microham MK2 for several years
without problems.
This morning, the sound from the DVK (in the MK2) doesn't seem to get
through to the K3.
Using my normal mic (from headset) also through the MK2, and that works.
When playing the DVK message,
for microHAM USB Device Router when you play a DVK message.
Finally, open Windows Control Panel | Playback Headset Earphone - Levels
and check the balance (should be equal or all left).
73,
... Joe, W4TV
On 2015-01-11 7:19 AM, Evert Bakker wrote:
Hello,
Haven been using my K3 in combi
Hi Joe,
-- Any other application in the computer can cause problems for the DVK --
My best guess it was WSJT (I have been running meteorscatter on 3/4 jan)
-- You grabbed control back by reselecting the sound card. --
I guess that was the story!
Windows
I'm addicted to homebrewing
Just a short question,
Anyone around here who has got the manual of the G800SDX Yeasu Rotor?
PLease respond off list
73's, Evert PA2KW
Sri for the bandwidth
.
__
Elecraft mailing list
Home:
Thanks for all responses. Great!
-Oorspronkelijk bericht-
Van: Elecraft [mailto:elecraft-boun...@mailman.qth.net] Namens Evert Bakker
Verzonden: woensdag 6 augustus 2014 10:32
Aan: elecraft@mailman.qth.net
Onderwerp: [Elecraft] off topic
Just a short question,
Anyone around here who has
Hello,
Excuse me for the little side step
I used to have the CMOS Super Keyer II for more then 20 years I guess and
always had fun using it.
It was the way I learned to paddle.
After I got the K3, the first 2 years I used the internal K3 keyer and it
was doing a good job. It just gave
Hello Wayne,
Good news!
Will it be possible to split TX and RX functionality between the homeK3
(TX) and the remote K3 (RX) in a setup where the RX controls on the home
K3 are used as the frontpanel for the remote K3 ?
Just want to use my second K3 for remote listening.
73's, Evert
This happens as well when you switch bands :-(
73's, Evert PA2KW
I notice that if I select DATA A mode and set the bandwidth to, say, 1.5
kHz, then rotate the B VFO through the several data modes, upon returning to
DATA A I have to readjust the bandwidth control once again.
Hello
When running Data-Mode and using 31 Bps PSK-D (using the internal CW to PSK
converter) it is not possible to work split with VFO A and B
But Data-Mode using 45 Bps FSK-D split is possible. Did I run into a bug?
I solved this momentarily by using the XIT.
Anyone else having this
I was one of the early complainers about all kind of artifacts in the
audio. I'm blessed with a high Fc in my ears. This revealed that strong
signals and especially AM (which I never do, but when tapping through the
modes it was easy to notice) were awfull to listen to (for me).
I used the Heil
Hello,
On my old KXV3 I installed a small PCB with sticky tape. It was an original
Elecraft mod.
As far as I know this mod was installed to improve isolation of the receive
antenna on the original KXV3 board.
Now I'm installing the KXV3A board I have the next question:
Do I have to
Just tried working PSK 31 (Data Mode) but can't work split. Used the AB tap
twice to copy all info to VFO B.
Am I doing something wrong here or did I run into a firmware issue? I did
use the XIT, which works.
I used the paddles to generate PSK.
FW = 3.66
73's, Evert PA2KW
Is Elecraft closed these days? (Vacation)
73's, Evert PA2KW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list
: Tuesday, December 29, 2009 00:37
To: ev...@pa2kw.com
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Vacation
Evert,
They are open today, but running with a skeleton staff - yes, vacations.
73,
Don W3FPR
Evert Bakker (PA2KW) wrote:
Is Elecraft closed these days? (Vacation)
73's
I'm trying to connect my K3 to the MicroHam MKII.
I'm struggling already for two weeks now to let the MKII to stop putting my
K3 into TX mode (unwillingly).
When I switch on the K3 and the MKII (both on a different power supply)
nothing goes wrong so far.
But as soon as the router is started,
Hello,
This evening I was warned by a friend that my signal sounded like an old
Russian station (sri guys), tjouping (I really don't know what other
word to use)
Details:
Release 3.14 / 2.16
Split operation (calling TX3A)
Sub RX OFF
RX 10.114,20 Mc
TX 10.118,38 Mc
Amplifier switched
Hello Julian,
In the past (2x), but not lately.
I might do this again.
I'll first check it tomorrow and see if the problem is still there.
Thanks for the reply!
73's, Evert PA2KW
Julian wrote:
Have you tried a VCO calibration?
__
Hi Tom,
--- Good headphones designed for communications shouldn't even go that
high. ---
May be you are (should be) correct. But my Heil Pro does as I do hear these
high tones coming through.
Just an example; when using SSB (MON =2) 30% of the time I clearly hear a
tune of high frequency (must
Hello Paul,
Just for this situation it's not a blessing to hear that high.
I'm still able to hear up to 21 Kc (it was 28 Kc about 15 years ago).
So I'm looking forward for this LPF board! I'll contact Elecraft and see if
that will do the job.
I'll try the Elco's and see what the result will be.
Larry,
If your ears go beyond 16 Kc, you won't be pleased.
73's, Evert PA2KW
But then I saw the Pro Set K2 on the web site.
Any body using one on a K3, as well?
de K2GN/Larry
K3 - S/N 3278
__
Elecraft mailing list
Home:
Joe,
That this operation is on V/UHF is no justification for liddish
behavior.
I'm sorry to say so, but this sounds like an emotional opinion based on the
(US ?) relation between CB and roger beeps.
There is absolute no reason why someone is not allowed to use is. Liddish
behavior is
I have my K3 loaded with KRX3, KXV3 and KAT3.
The AUX-RF BNC is used for the Sub-RX and connected to the RX antenna
(K9AY).
Diversity receiving with the K9AY and the main antenna works fine.
I don't want to use ANT2 on the KAT3 for receiving antenna's as I might
accidentally switch the TX to
I was playing with HRD this afternoon and when swapping bands I ended up on
14 Mc in LSB mode..
I've been trying to get it on USB again but I'm missing something I guess
(and didn't even have a beer this afternoon.)
Where can set the proper mode again?
73's, Evert PA2KW
Problem solved. I think the LSB mode is somewhere disabled for 14 Mc.
By toggling the mode (up) I didn't get the USB Mode. (For some unknown
reason I'm always toggling up until I get what I want).
By toggling down I did get back the USB mode.
Wheird
73's, Evert PA2KW
- if you want to change to the opposite sideband, hold
ALT - the K3 remembers that setting per band, per VFO.
73,
Don W3FPR
Evert Bakker (PA2KW) wrote:
Problem solved. I think the LSB mode is somewhere disabled for 14 Mc.
By toggling the mode (up) I didn't get the USB Mode. (For some
Hello,
A friend of mine is considering the purchase of a XV144.
Is there somebody out there who wants to sell his XVRT?
Please let me know (of list).
73's, Evert PA2KW
__
Elecraft mailing list
Home:
Hello Ralph,
It is a known issue and can be solved easily.
I'll send you the document directly (which is on the Website as well).
73's, Evert PA2KW
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ralph
Sent: Saturday,
Hello,
It looks like I'm not able to get RF power out on either ANT1 (28 Mc) and
KXV3 (XVRT-OUT) in FM Mode.
Receiving seems to be OK.
With the K3-Utility I enabled FM at FL1 position. FL1 is the KFL3B-FM and
set a dot at TX-FM.
K3-SN0812 (with FM and KXV options)
K3-utility
Tnx Lyle,
It is.
73's, Evert PA2KW
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Lyle Johnson
Sent: Thursday, July 30, 2009 22:05
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 TX FM
It looks like I'm not able
Evert, what is your deviation setting in the menu?
James K2QI
On Thu, Jul 30, 2009 at 4:13 PM, Evert Bakker (PA2KW) ev...@pa2kw.com
wrote:
Tnx Lyle,
It is.
73's, Evert PA2KW
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net
Hello,
As temperature rises (in the shack), FP (34 degC) does, and a problem
popped up; ERR PL1.
I did check the PLL voltage. PLL1 = 7.5 (which seems to be the limit I
guess), PLL2 = 3.5 (Sub-RX) at 28 Mc and FP 34 degC
When FP was 22 degC: PLL1 = 3.8 and PLL2 = 3.4.
After
Hello Brett,
Your question:
Is it normal for the right side to run quite a bit warmer after installation
of the KRX3.
I did notice the same effect. I asked support and they confirmed it as
something normal. (I didn't expect that increase in heat production as
well).
73's, Evert PA2KW
Great news about the K144XV!
I just wonder if the K144XV has the possibility to separate the RX input
and TX output and are separately available at the back panel?
(A lot of VHF Dx-ers use only 1 relay, the one in top of the tower, where
the preamp is installed as well.)
73's, Evert
Great news about the K144XV!
I just wonder if the K144XV has the possibility to separate the RX input
and TX output and become available at the back panel?
(A lot of VHF Dx-ers use only 1 relay, the one in top of the tower, where
the preamp is installed as well.)
73's, Evert PA2KW
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill W4ZV
Sent: Monday, April 06, 2009 14:11
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 audio
Evert Bakker (PA2KW) wrote:
For me, I'm quite sure it has to do
: Monday, April 06, 2009 17:33
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 audio
Evert Bakker (PA2KW) wrote:
For me, I'm quite sure it has to do with the digitalization. That sound is
far from natural and is ADDITIONAL to the normal audio signal. That
addition
sounds sharp
Maarten Wrote:
Several other operators also stated the K3's audio was hissy and sharp
and not nice and smooth. We could hear it using the built-in speaker as well
as on a Heil Pro Set Plus.
I think there is nothing wrong with your K3.
About a week ago I reported the bad audio quality of the
in this region that
enables one to detect these K3 abnormalities?
Steve Ellington
n...@carolina.rr.com
- Original Message -
From: Evert Bakker (PA2KW) ev...@pa2kw.com
To: 'Maarten van Rossum' pd2r.maar...@gmail.com; 'Elecraft Group'
elecraft@mailman.qth.net
Cc: 'Gary Surrency' supp
.
-Jack Brindle, W6FB
===
On Apr 5, 2009, at 10:39 AM, Evert Bakker (PA2KW) wrote:
Maarten Wrote:
Several other operators also stated the K3's audio was hissy and
sharp
and not nice and smooth. We could hear it using
Hi Don,
It is definitely not band-noise what I'm talking about.
You need a decent signal level (audio strength) to hear it.
For me, I'm quite sure it has to do with the digitalization. That sound is
far from natural and is ADDITIONAL to the normal audio signal. That addition
sounds sharp,
Hello,
As this question is about peripherals, I don't know if it is allowed to, but
I give it a try. (if not let me know).
I bought (locally) a Heil-Proset with the HC4 element to use in combi with
the K3.
I used to have a 20 year old Telex (very tiny headphone, mono wired and no
] On Behalf Of Evert Bakker (PA2KW)
Sent: Sunday, March 22, 2009 14:21
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 Hiel Proset
When I listen to stronger stations (more volume) it sounds like clouds with
a silver line where the silver line is a very distorted high frequency
product
In the contrary,
Service is: SUPER .!.
73's, Evert PA2KW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted
Hello Don,
I do have a similar effect except that my first and second radio is a K3
(SN-0812 and SN-2185).
- Same power-supply at the same time radio's ON
- both on 50 Ohm dummy load
- same roofing filter (2.7 Kc)
- same filter gain (0 dB)
- same DSP setting (Bw = 3.0 Kc / Fctr = 1.5 Kc)
-
: Monday, March 16, 2009 20:24
To: ev...@pa2kw.com
Subject: Re: [Elecraft] Hot K3
You didn't mention ATT and PRE. I have found that sometimes when I reset my
K3 it goes back to settings that turned one or the other on without my being
aware of it.
73,
Dave AB7E
Evert Bakker (PA2KW) wrote
I'm installing my KRX3 now and trying to figure out which configuration to
install.
After reading the KRX3 manual and the K3 manual and looking at the pictures
on page 40 (K3 manual),
I do have KAT3 and KXV3 installed.
I do have a separate RX antenna for the low bands.
I want to use the
Hello,
This weekend I found some time to connect my Micro-Keyer II to the K3.
After playing around a while with the software (try and error method) I
ended up with an K3 not doing what I want.
I thought that the MKII was causing the problem so I disconnected everything
except the paddle,
Subject: Re: [Elecraft] K3 CW/MIC problems
VOX on ?
Problem solved
73's, Evert PA2KW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Disabling TX-ing can be done by TX-TEST mode, so which specific situation
requires disabling the VOX in CW mode?
Just curious, no more
73's, Evert, PA2KW
__
Elecraft mailing list
Home:
been working RTTY split, using paddle input, with no
problem and through all the updates.
Dave W7AQK
- Original Message
From: Evert Bakker (PA2KW) mailto:ev...@pa2kw.com
To: 'Elecraft mailto:elecraft@mailman.qth.net Discussion List'
Sent: Saturday, February 21, 2009 4:36
I have firmware version 2.67/1.96.
In this version it is still not possible to use CW to RTTY when using SPLIT.
Has this been fixed in the newer firmware version?
I now use XIT, but this is not so powerfull.
73's, Evert PA2KW
Hello,
During the initial calibration test, one is asked to set CONFIG:KXV3 to
TEST. This one is not available (just NOT INST and NOR).
What am I doing wrong?
73's, Evert PA2KW
__
Elecraft mailing list
Home:
Thanks! It works!
-Original Message-
From: Gary Hvizdak [mailto:garyhviz...@cfl.rr.com]
Sent: Friday, February 13, 2009 12:45
To: elecraft@mailman.qth.net
Cc: ev...@pa2kw.com
Subject: RE: [Elecraft] K3 KXV3 mode
On Fri Feb 13 06:20:26 EST 2009 Evert Bakker (PA2KW) wrote ...
During
Just a question about the power calibration of the K3as the procedure is not
clear to me.
1) Select 160 m.
2) Set the power knob to 5W (on the K3-LCD display)
3) Set the K3 in Tune
4) Measure the output power with an external power meter (I'm using a
LP100) into a
Lance,
This is the only proper way for serious VHF stations. Use your feedback
contact of the final RX/TX coaxial relay (which is most probably mounted in
the top of your tower) as a final go for the RF out of the K3 by using the
TX-Inhibit Line.
73's Evert PA2KW
Cu
-Original Message-
Hello Doug,
Here some basics about preamps. I will try to make it short, but I could
expand to pages
A preamp only makes sense if the noise-figure (NF) of the preamp is better
than the NF of the normal input stage (usually the normal frontend input).
Each stage in a receiver (frontend,
Looks like I run into a bug (version 2.67).
When the CW delay is activated by pushing the with the speed/mic (digital)
potentiometer, the AF potentiometer isn't working.
73's, Evert PA2KW
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
After the latest firmware update I noticed that when in CW mode the Key Out
was switching with the Dit's and Dah's which wasn't the case before.
I only could prevent this by switching the VOX on at the front panel. I
guess the older version had automatically the VOX on, but didn't show it on
the
: Re: [Elecraft] K3 / HRD
Evert,
That is strange. Unless the computer is loaded down with other chores,
HRD normally updates very quickly. You may want to check for 'gremlins'
in your computer, or other things that are keeping the CPU busy.
73,
Don W3FPR
Evert Bakker (PA2KW) wrote:
I'm just
I'm just in the process of selecting a log program.
For that reason I was testing HRD to communicate with my K3.
I got it working (at the highest speed) through the (K)USB device (from
Prolific). But it's awful slow.
When changing the VFO-freq, it might take more then a minute for HRD to
Is there someone in Europe who is planning to split his KPA100 from the K2
and placing it in a separate EC2 enclosure?
I sold my K2 so I've got some parts available like: an EC2 enclosure (used 6
month but like new) and the KIO2 build and ready to go including the
interconnection control cable.
I got the question from someone:
Is your K2/100 upp to latest version, revision, firmware...
Where can I find..How do I check?
I've got K2-SN4836
73's, Evert PA2KW
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a
Wim,
If 1 dB noise figure is the aim, I would make one myself (sure better NF,
most probably cheaper).
73', Evert PA2KW
Active on 144
Preamp NF 0.15 dB (MGF1302 - YU1AW design)
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Enno, PF5X
Sent: Monday,
ACS, would be nice (used it for the last 20 yrs)
Low priority (to me), I'm sure there are more important issues
73's, Evert PA2KW
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info
Hi Mike,
Yes I did not read your message carefully enough.
I had a similar problem as I wrote, but that wasn't in the tune mode.
Your problem has been solved easily :-)
I'll try solving my problem again next weekend.
Thanks for e-mail!
73's, Evert PA2KW
-Original Message-
From:
Thanks to all who responded,
I just worked 2 station on RTTY (my first -:) )
You just have to get used to it, but for now and then is OK.
73's, Evert PA2KW
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Evert Bakker (PA2KW)
Sent: Sunday, June 01, 2008
Hello,
I'm basically a cw operator, but this morning I heard OH0 on 24 Mc in RTTY.
Well, time to test the K3 features.
After some reading and testing I got it decoding RTTY. I used Data Mode /
AFSK A, 45 Bps / Pitch 915 - 170. I hope this is a correct setting for auto
decoding RTTY.
Then I
Hello Mike,
I've seen similar behavior on my K2 when using it with a transverter and
power amplifier although it wasn't that bad. I was not able to solve the
problem. I did a lot on earthing, wiring or positioning equipment and
antenna direction, but it was consistent.
I'm almost sure that it is
That's what I hear as well.
73'e, Evert PA2KW
---
I don't hear a birdie on that frequency, but centred around there is a
broad peak of rasping noise and transient carriers that only appear
while rotating the VFO A knob.
--
I do!
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of G4ILO
Sent: Sunday, May 25, 2008 22:06
To: elecraft@mailman.qth.net
Subject: RE: [Elecraft] K3 10M Birdie
What's the big deal with birdies? Perhaps if you are operating from the
middle of nowhere
You can add me to the list of persons that would like to see that feature. I
do have the CMOS Super Keyer 1 as well and it's hard to get it right after
15 years of operating and suddenly missing ACS.
No top priority, but I would like to drop a separate piece of equipment.
73's, Evert PA2KW
Hello all,
Today I received the 1.8 Kc 8 pole filter and installed it tonight.
I did the configuration with the software tool used for firmware updates as
well (also performed an update as well).
All went OK, but I do have a feeling something is wrong or my ears/brains
work a little
Of Evert Bakker (PA2KW)
Sent: Wednesday, May 21, 2008 23:58
To: 'Elecraft Reflector'
Subject: [Elecraft] Xtal Filters
Hello all,
Today I received the 1.8 Kc 8 pole filter and installed it tonight.
I did the configuration with the software tool used for firmware updates as
well (also performed
operators.
Knut - AB2TC
Evert Bakker (PA2KW) wrote:
Hello all,
Today I received the 1.8 Kc 8 pole filter and installed it tonight.
I did the configuration with the software tool used for firmware updates
as
well (also performed an update as well).
All went OK, but I do have
Dick,
You are is correct!
I had (still have) the same flipped Fan panel.
I'm glad it's the back-side
73's, Evert PA2KW
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Dick Roth KA1OZ
Sent: Saturday, May 10, 2008 18:53
To: Elecraft Reflector; K3
Hello,
When using the button AB (VFO info transfer) the mode from A is not
transferred to B.
Was that supposed to be so or asked for? Especially now when CW is possible
in SSB mode, you might not notice it when B was on SSB and you quickly want
to transfer CW info to B for split operation.
Good day all,
I just uploaded the new firmware version which went smoothly.
After that I had to do some filter settings as I had my FM filter (yes, it
is in slot 1) already installed but it had to be enabled since the FM mode
is available now.
Normal procedure: go to Config, select a filter and
Hello all,
After having completed the assembly process of the K3, it was time to check
for updates with the utility software.
All seems to work, but.
I saw an update op DSP2 (1.55). In my K3 the status was N/A. An update I
would say. But the button send to K3 wasn't available.
Was this
]; 'Elecraft Reflector'
Subject: Re: [Elecraft] Firmware uploads
DSP2 is for the subreceiver .. and you don't have one.
Don K7FJ
- Original Message -
From: Evert Bakker (PA2KW) [EMAIL PROTECTED]
To: 'Elecraft Reflector' elecraft@mailman.qth.net
Sent: Friday, May 02, 2008 1:12 PM
Subject: [Elecraft
Good day to all,
First of all:
K3 (812) arrived.
Ordered 21 Nov 2007
Order confirmation 22 april
Sent 24 april
Arrived 28 april
Let's see if reality meets expectations(I'll let you know)
I've finished the building procedure and in the process of calibration.
When calibrating the TCXO (1
Thanks to all who responded!
Problem solved, K3 running (10W)
73's, Evert PA2KW
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Evert Bakker (PA2KW)
Sent: Thursday, May 01, 2008 13:10
To: 'Elecraft Reflector'
Subject: [Elecraft] K3 TCXO calibration
I think the problem is not elecraft rigs but amplifiers that have
unreasonably slow switching times.
10msec or longer is unreasonably slow and I think it's 'unreasonable' to
blame the manufacturer of the radio because the amp manufacturer saved a
few bucks and used a cheap, slow relay instead
I agree an inhibit pin is a very good idea.
Thanks a million for the developers for giving this inhibit possibility.
This makes serious VHF high power applications possible.
Don't remove this option please!!
THANKS
(waiting for my K3 as the IF stage for my VHF station)
73's, Evert PA2KW
Lenny W2BVH wrote:
Has anyone on the list used WSJT FSK441 mode with a K2? If so I'd like
to hear about your experience.
Hello Lenny,
Yep I did and do! And I can tell you that it works fine. It's a bit late
here, so
Hi Mike and Lenny,
Using FSK441, don't change the tones (as far as I know you can't).
Just tune in for the RX signal and the DF will show you how to tune in on
your partner. From then on it should be OK.
73's, Evert PA2KW
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL
Thanks Don for the historical-technical backup!
I've got SN4836 so won't have that problem.
73's, Evert
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Don Wilhelm
Sent: Monday, March 03, 2008 23:10
To: w2bvh
Cc: Elecraft@mailman.qth.net
Subject: Re:
Finally worked the VP6DX guys on 24 Mc this afternoon with my K2.
Worked them in 12 slots now with only 100W !
I like my K2/100-SN4836 (and Drake TR7 on the low freq's)
I hope the K3 will be able to compete with, and finally replace the Drake
TR7/R7/RV7 (receiver/audio/NB quality)
I ordered in
Hello all,
I'll be qrv from a small clubstation (PI4EDE) during the PACC contest with
my K2 (mainly CW ofcourse)
Unfortunately my K3 is too late for this event, but the K2 will do fine as
usual.
Hope cul.
73's, Evert PA2KW
___
Elecraft
Problem solved.
I Just removed the KIO2 and the KXV2, tested the K2 (all OK) reinserted the
KXV2 (all OK) and finally reinserted the KIO2 (all OK)
Magic hands I suppose :-).
Have a nice weekend.
73's, Evert PA2KW
After installing my KIO2 module in the K2 (I want my KPA100 remote) I did
all
Hello all,
After installing my KIO2 module in the K2 (I want my KPA100 remote) I did
all proposed tests to see if the KIO was working. I was using the K2-remote
program C 2001 Elecraft LLC and changing settings on 7 Mc. All looked
fine, and up to the end.
I finally completed the mechanical
Hello all,
Before I start to look in the manuals...
Do I need the KIO2 module when I want to use my KPA100 in a separate
enclosure?
Do I need more then that?
Thanks in advance
73's, Evert PA2KW
___
Elecraft mailing list
Post to:
Werner,
The inductive resistors are light-blue/grey.
I replaced mine as well. They should have a reddish-brown colour now.
Also a capacitor C31 should be replaced (was 0.033uF and should be 0.22 uF)
73's, Everet PA2KW
___
Elecraft mailing list
Post
Hello Ron,
Yes I am.
I raised this issue several month ago during the announcement of the K3.
I did suggest the Ten-Tec solution which works fantastic.
Before RF gets out (either from the main antenna or transverter RF-out), the
TX-Request initiated by the PTT/VOX/Key from the K3 (which should be
Sir,
It's always good to exchange thoughts about the possible use and features of
Elecraft products. I know the products of DEM but all of them doesn't
prevent the exiter to give RF if one piece of the added hardware isn't
working properly.
73's Evert PA2KW
-Original Message-
From:
Hi Tom (and others),
I think Don answered almost complete to your question but
I'd like to elaborate a little on this subject which is unnecessary for and
even unknown by most HF operators.
For serious VHF/UHF operation, it is important to have a system with low
noise figure (typical between
Hi John,
I've been struggling around as well to realize a safe and reliable setup for
the combination K2 / Transverter / Power-Amp / Pre-Amp / Coaxial relay, from
which the last three components in a separate box mounted in top of the
antenna tower.
It is no way safe to use the 8R or 8T voltage
Last weekend I used my K2 in combination with my own designed/build 44 Mc
transvertor for meteor-scatter QSO's. Last week I finished my audio
interface / sequencer to give me isolation between PC and K2 / save my
preamp when running a high power amplifier respectively. The K2 has the
K60XV option
1 - 100 of 127 matches
Mail list logo