: [Elecraft] KX3 Amp
Just FYI, I got the Elecraft 100W amp in two or three weeks ago. At over $
1100 it better beat these other amps. It has a tuner but I also have the ATU
in the KX3 and two more discrete ATU's for higher power, balanced (PAL) ,
etc.
Have you tried the Elecraft amp yet ?
Bill
: [Elecraft] KX3 Amp
One correction. The HF Packer is not a 50w amp. It's about 45w at 160m,
and then steadily less as you go up in frequency (40w for 80m, 35w for
40-20m, 30w for 17/15m, 25w for 12m and about 20w for 10m). It doesn't
support 6m. These numbers come directly from a graph
With all the banter about KX3's and amp's, on batteries for Emergency
use.
Please remember, that battery makers specify the AH figure, for a typical
C/20 rate, (1/20th the nominal AH current value.) Some may quote it at
C/10, check the data sheets for the battery of interest, they will often
Exactly right, Dave. I should have thought to mention this.
73, Jim K9YC
On 7/1/2013 6:27 AM, Dave B wrote:
Please remember, that battery makers specify the AH figure, for a typical
C/20 rate, (1/20th the nominal AH current value.) Some may quote it at
C/10, check the data sheets for the
, June 30, 2013 3:43 PM
Subject: Re: [Elecraft] KX3 Amp
Jim is right in one sense that the 100w amp will consume battery life quickly.
However, if what you want is the ability to get a signal out at marginal
propagation conditions, then a 50 watt amp if used frugally can get a stronger
signal
UA9CDC
- Original Message -
From: John Marvin jm...@themarvins.org
To: elecraft@mailman.qth.net
Sent: Monday, July 01, 2013 11:54 AM
Subject: Re: [Elecraft] KX3 Amp
One correction. The HF Packer is not a 50w amp. It's about 45w at 160m,
and then steadily less as you go up in frequency
John Marvin wrote
One correction. The HF Packer is not a 50w amp. It's about 45w at 160m,
and then steadily less as you go up in frequency (40w for 80m, 35w for
40-20m, 30w for 17/15m, 25w for 12m and about 20w for 10m). It doesn't
support 6m. These numbers come directly from a graph in the
, K6KBE
From: Ariel Jacala [hidden email]
To: elecraft reflector [hidden email]
Cc: [hidden email] [hidden email]
Sent: Sunday, June 30, 2013 3:43 PM
Subject: Re: [Elecraft] KX3 Amp
Jim is right in one sense that the 100w amp will consume battery life
Marvin [hidden email]
To: [hidden email]
Sent: Monday, July 01, 2013 11:54 AM
Subject: Re: [Elecraft] KX3 Amp
One correction. The HF Packer is not a 50w amp. It's about 45w at 160m,
and then steadily less as you go up in frequency (40w for 80m, 35w for
40-20m, 30w for 17/15m, 25w for 12m
Unfortunately , yes , I do need an amp. . We are going out over 200 mi. from
the nearest real town and if we need help then I would really love to get
through vs. be falsely proud of my QST skills that gets me nothing but dead
air while we hike back with no medical or rescue personnel knowing we
On 6/30/2013 4:42 AM, KF5TEU wrote:
Unfortunately , yes , I do need an amp. . We are going out over 200 mi. from
the nearest real town and if we need help then I would really love to get
through vs. be falsely proud of my QST skills that gets me nothing but dead
air
It's important to
Jim is right in one sense that the 100w amp will consume battery life quickly.
However, if what you want is the ability to get a signal out at marginal
propagation conditions, then a 50 watt amp if used frugally can get a stronger
signal out. Several amps fall into this category with about a
I love amateur radio.
However, if I was living 200 miles from the nearest real town, I'd
invest in a good Personal Locator Beacon (or two) . The kind with a
built-in GPS.
Sure, it's not communications but it's a one-button come get us,
we're right here and the Search and Rescue Satellites
That's what I'd do as well. Some personal locators will send an I'm
OK message, too to designated recipients. And, if you don't want to
buy a personal locator... you can rent them, which might be less
expensive, if it's a one-time trip.
73 de Ray
K2ULR
KX3 #211
On Jun 30, 2013, at 7:43
Mine was about $250 -- a lot less than an amplifier that isn't
guaranteed to get someone to send help.
On 6/30/2013 4:51 PM, Ray Sills wrote:
That's what I'd do as well. Some personal locators will send an I'm
OK message, too to designated recipients. And, if you don't want to
buy a
Jun 2013 19:51:08 -0400
Subject: Re: [Elecraft] KX3 Amp
That's what I'd do as well. Some personal locators will send an I'm
OK message, too to designated recipients. And, if you don't want to
buy a personal locator... you can rent them, which might be less
expensive, if it's a one-time
Well, in that framework - I would have to agree that the PLB is better .
How do I get one :-)
Ariel NY4G
Date: Sun, 30 Jun 2013 17:24:45 -0700
From: k...@coldrockshotbrooms.com
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Yes, but.
The original poster
Yes, but.
The original poster is going to be 200 miles from town. He may or may
not be in VHF range of something when he needs help. I'm pretty sure
he's out of range or he'd just get a couple of handhelds and call it done.
The Personal Locator Beacon frequency is monitored by two sets
:
Well, in that framework - I would have to agree that the PLB is better .
How do I get one :-)
Ariel NY4G
Date: Sun, 30 Jun 2013 17:24:45 -0700
From: k...@coldrockshotbrooms.com
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Yes, but.
The original poster
: wun...@wunderwood.org
Date: Sun, 30 Jun 2013 17:41:59 -0700
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
There are a lot of emergency situations that benefit from two-way
communication. PLBs are great for sinking ships, but not so good for
distinguishing between a wildfire
Jacala wrote:
Well, in that framework - I would have to agree that the PLB is better .
How do I get one :-)
Ariel NY4G
Date: Sun, 30 Jun 2013 17:24:45 -0700
From: k...@coldrockshotbrooms.com
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Yes, but.
The original poster
Or .maybe he's trying to justify the purchase of an amp to his Financial
Control Officer.
...bill nr4c
Sent from my Verizon Wireless 4G LTE DROID
Lynn W. Taylor, WB6UUT k...@coldrockshotbrooms.com wrote:
Yes, but.
The original poster is going to be 200 miles from town. He may or may
:-)
Ariel NY4G
Date: Sun, 30 Jun 2013 17:24:45 -0700
From: k...@coldrockshotbrooms.com
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Yes, but.
The original poster is going to be 200 miles from town. He may or may
not be in VHF range of something when he needs help
: Sunday, June 30, 2013 6:06 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
PLBs actually aren't legal for sinking ships (or crashing airplanes), there
is a different category of device for that.
Personal Locator Beacons are meant to do one simple task: summon help in an
emergency
Jacala wrote:
Well, in that framework - I would have to agree that the PLB is better .
How do I get one :-)
Ariel NY4G
Date: Sun, 30 Jun 2013 17:24:45 -0700
From: k...@coldrockshotbrooms.com
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Yes, but.
The original poster
NY4G
Date: Sun, 30 Jun 2013 17:24:45 -0700
From: [hidden email]
To: [hidden email]
Subject: Re: [Elecraft] KX3 Amp
Yes, but.
The original poster is going to be 200 miles from town. He may or may
not be in VHF range of something when he needs help. I'm pretty sure
he's out
From: [hidden email]
To: [hidden email]
Date: Sun, 30 Jun 2013 19:51:08 -0400
Subject: Re: [Elecraft] KX3 Amp
That's what I'd do as well. Some personal locators will send an I'm
OK message, too to designated recipients. And, if you don't want to
buy a personal locator... you
I appreciate the low power is better for longer advice but..this is for that
crucial 5 min. of comm. when low power just doesn't work.
We have several 13500 MaH/5A power packs that combine for 20 plus amps and
weigh about 1lb. each. We also have the vehicle batteries , aircraft batteries
and
: [Elecraft] KX3 Amp
That's what I'd do as well. Some personal locators will send an I'm
OK message, too to designated recipients. And, if you don't want to
buy a personal locator... you can rent them, which might be less
expensive, if it's a one-time trip.
73 de Ray
K2ULR
KX3 #211
on HF. When the 2m module gets out - I have a
complete package for all modes of remote operation.
Ariel NY4G
From: [hidden email]
To: [hidden email]
Date: Sun, 30 Jun 2013 19:51:08 -0400
Subject: Re: [Elecraft] KX3 Amp
That's what I'd do as well. Some personal locators will send
Hmm, reading all this and wondering (wanting) more clarification of
what is meant by We are going out over 200 mi. from
the nearest real town
That would describe 75% or maybe 90% of Alaska. If this is a
short-term camping trip or vacation it will be a bit different from
living full-time
] KX3 Amp
That's what I'd do as well. Some personal locators will send an I'm
OK message, too to designated recipients. And, if you don't want to
buy a personal locator... you can rent them, which might be less
expensive, if it's a one-time trip.
73 de Ray
K2ULR
KX3 #211
On Jun 30, 2013, at 7:43
Hi Eric,
Do you have any physical dimensions that you can release such as height,
length, depth?
Thanks,
Carlton
K2CMH
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KX3-amp-tune-tp7574521p7574593.html
Sent from the Elecraft mailing list archive at Nabble.com.
Will they both going to be available at the same time? 73 George/W2BPI
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
yes.
Eric
elecraft.com
On 5/30/2013 4:49 PM, w2b...@aol.com wrote:
Will they both going to be available at the same time? 73 George/W2BPI
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
the
surgery.
Home now :-)
73,
Geoff
LX2AO
- Original Message -
From: Igor Sokolov ua9...@gmail.com
To: Geoffrey Mackenzie-Kennedy lx...@pt.lu
Cc: Elecraft Discussion List elecraft@mailman.qth.net
Sent: Saturday, April 06, 2013 9:16 PM
Subject: Re: [Elecraft] KX3 Amp
Geoff,
Thank
- Original Message -
From: Geoffrey Mackenzie-Kennedy lx...@pt.lu
To: Igor Sokolov ua9...@gmail.com
Cc: Elecraft Discussion List elecraft@mailman.qth.net
Sent: Tuesday, March 26, 2013 8:59 PM
Subject: Re: [Elecraft] KX3 Amp
Hello Igor,
If you want to measure (with useful accuracy
Hello Igor,
If you want to measure (with useful accuracy) the level of the IMD products
generated by your KX3 and HLA 300 Plus, all that you would need in addition
to your TS590 is a Two Tone (AF) Generator, an AF Spectrum Analyser and your
computer. If you Google Tcube you will find a
There is a 2 Tone generator built into the KX3. See the menu listing
for details.
73,
Don W3FPR
On 3/26/2013 10:59 AM, Geoffrey Mackenzie-Kennedy wrote:
Hello Igor,
If you want to measure (with useful accuracy) the level of the IMD
products generated by your KX3 and HLA 300 Plus, all that
Don,
If the output of the 2 Tone generator which is built into the KX3 is
injected into the audio chain before any speech processing circuitry, yes
the internal 2 Tone generator could be used.
73,
Geoff.
LX2AO
On March 26, 2013 at 4:19 PM, Don Wilhelm wrote:
There is a 2 Tone generator
Hi All,
To echo Jim Brown's cautionary statement about IMD with the RM Italy HLA
series amps, there is some good info on Tom Rausch's (W8JI) website
concerning the HLA-150. That amp will run up to 150 watts or so, but
according to some testing that Rausch did, if you go much over 100 watts,
:40 PM
Subject: [Elecraft] KX3 Amp
Hi All,
To echo Jim Brown's cautionary statement about IMD with the RM Italy HLA
series amps, there is some good info on Tom Rausch's (W8JI) website
concerning the HLA-150. That amp will run up to 150 watts or so, but
according to some testing that Rausch
...@mailman.qth.net] On Behalf Of Greg
Sent: Friday, March 22, 2013 3:27 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Well it may be a waste of money for you but it is worth about 10 db to
everyone else... ;) 73, Greg-N4CC
-Original Message-
From: elecraft-boun
: Friday, March 22, 2013 3:27 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Well it may be a waste of money for you but it is worth about 10 db to
everyone else... ;) 73, Greg-N4CC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun
--KPA500--KAT500--W2
From: Gary Gregory [mailto:vk1zzg...@gmail.com]
Sent: Sunday, March 24, 2013 4:12 AM
To: Fred Smith
Cc: Greg; elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Not sure 11W drive is good for normal rag chewing with the KX3. It does get
rather hot to touch.
I
...@gmail.com
To: Fred Smith m...@mo-net.com
Cc: elecraft@mailman.qth.net
Sent: Sunday, March 24, 2013 3:11 PM
Subject: Re: [Elecraft] KX3 Amp
Not sure 11W drive is good for normal rag chewing with the KX3. It does
get
rather hot to touch.
I would hope that the KXPA100 would only require 5W
On 3/24/2013 3:20 AM, Igor Sokolov wrote:
I get 200-250W from HLA 300 Plus with 5W from KX3. Suits me just fine.
HLA 300 Plus sells at Amazon for under 500 $ Fully automatic and
integrates perfectly with KX3.
What is the IMD performance of this amplifier? Have you measured it?
Have you seen
@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Not sure 11W drive is good for normal rag chewing with the KX3. It does get
rather hot to touch.
I would hope that the KXPA100 would only require 5W for 100W output or
close to that.
73
I've been having a blast playing with my new KX3 for the past couple of
weeks and am now looking forward to adding a 100W amp. What kinds of
amps are people using with the KX3? Any that are particularly good or
bad? Any pitfalls? Thoughts about existing products vs. the new one from
Elecraft?
73,
Hi Giff K1GAH,
I am in progress of building my own amp according to the Motorola EB-104
application note;
www.ab4oj.com/dl/eb104.pdf
5-10W in, about 600W out depending on your DC supply, all-transistor-amp
using four MRF-150 power FET's. Remember to add a low-pass filter after
the amp.
- Original Message -
From: Giff Hammar lt;gham...@sv-phoenix.comgt;
To: elecraft@mailman.qth.net
Sent: Fri, 22 Mar 2013 12:20:50 - (UTC)
Subject: [Elecraft] KX3 Amp
I've been having a blast playing with my new KX3 for the past couple of
weeks and am now looking forward to adding a 100W
You do not need one :-)
72
Dom
M1KTA
On 22/03/13 12:20, Giff Hammar wrote:
I've been having a blast playing with my new KX3 for the past couple of
weeks and am now looking forward to adding a 100W amp. What kinds of
amps are people using with the KX3? Any that are particularly good or
bad?
On 3/22/2013 6:25 AM, k3...@comcast.net wrote:
The 100 Watter from Elecraft that matches your new toy should be out soon.
Dayton would be a good guess.
73, Jim K9YC
__
Elecraft mailing list
Home:
I bought a KX3 a bit over a week ago and have had a blast playing with
it. Now it's time to start thinking about an amp. I know the one
designed for it is supposed to be out by July, but I was wondering what
people are using now and whether or not they would recommend them to
others (I know that's
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
Message-ID: 514c500a.1020...@post.cybercity.dk
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
Hi Giff K1GAH,
I am in progress of building my own amp according to the Motorola EB-104
application note;
www.ab4oj.com/dl/eb104.pdf
I've been using a Tokyo High Power HL-45B and have been satisfied enough
with it. It's only 50 watts and it doesn't do automatic band switching with
the KX3 but the price point is well below where the Elecraft amp will
likely be announced.
Chris
AB3QV
On Wed, Mar 20, 2013 at 7:43 PM, Giff
I have been using a Hardrock which achieves 50 watts easy on all bands accept
6m (about 32 there). At about $250 - that is about $5 dollars a watt versus
Ten Tec at $8 a watt. The TenTec does auto band switching though. The
developers at Hardrock are working on a band switching code and may
I hadn't heard of this one. Is it for sale now? this web site says
it's waiting for FCC approval.
www.hobbypcb.com/amateur-radio/amateur-radio/hardrock-50-hf-power-amp-kit.html
Peter W0LLN
On Fri, Mar 22, 2013 at 12:44 PM, Ariel Jacala n...@hotmail.com wrote:
I have been using a
Given the message forum included on that web site it seems that people have
this kit and are using it, even with the KX3.
If you or others have this I am curious about QSK operation -- is it capable of
that or not.
Thanks,
73, phil, K7PEH
On Mar 22, 2013, at 11:09 AM, Peter Wollan
I have been using my KX3 for a few months now, and never needed an amp.
Nine out of ten times, if I hear someone, they can hear me (CW).
Actually, even with my K1 at 6W, I never felt the need.
For SSB, I can see how it would help, but for CW, it's a waste of money.
Gil.
On Fri, 2013-03-22 at 12:15 -0700, Donald Bush wrote:
Great stuff Gillow power really works if your patient and use a
decent antennas. I'm currently at 300 countries confirmed using 5
watts or less. I just worked the Clipperton Island DX-pedition last
week on 40 with ONE WATT.and I'm
@mailman.qth.net
Subject: Re: [Elecraft] KX3 Amp
I have been using my KX3 for a few months now, and never needed an amp.
Nine out of ten times, if I hear someone, they can hear me (CW).
Actually, even with my K1 at 6W, I never felt the need.
For SSB, I can see how it would help, but for CW, it's a waste
Is there a portable version?
:-)
Gary
On 6 November 2012 09:16, paim paimg0...@btinternet.com wrote:
Dan
yes look on this link http://www.dc9dz.de/en/tsunami40k.html
vy 73
E.P g0uut
__
Elecraft mailing list
Home:
Dan
yes look on this link http://www.dc9dz.de/en/tsunami40k.html
vy 73
E.P g0uut
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
In a much earlier question I had asked Wayne if the KX3 would be able to key
the Juma PA100D amplifier. He responded with a yes..
I tried it today with a cable from KX3 ACC2 to the T/R input on the Juma amp.
Yes it did key the amp, but when connected there was an appreciable receive
loss on
That sounds like Juma amp problem to me. The antenna to KX3 loss
during receive should be zero or close to it. Sounds like you need to
consult with Customer Support at Juma.
73,
Don W3FPR
On 7/3/2012 11:38 PM, Sid Leben wrote:
In a much earlier question I had asked Wayne if the KX3 would
Don That is for the little 100 watt amp coming for the KX3? Or were you
talking about the kpa500?
On Jun 1, 2012 7:40 PM, Gerald Manthey kc6...@gmail.com wrote:
Don
That is for the little 100 watt amp coming for the KX3? Or were you
talking about the kpa500?
On Jun 1, 2012 7:36 PM, Don
Gerald,
From what I know about the goals, the answer will be yes - it will work
with multiple transceivers, not just the KX3.
73,
Don W3FPR
On 6/2/2012 11:42 AM, Gerald Manthey wrote:
Don That is for the little 100 watt amp coming for the KX3? Or were you
talking about the kpa500?
On Jun
Maybe someone in the know could answer a question about the KX3 amp tuner
that will be developed. Will this amp tuner work on the K2/10 also?
Would be nice if it does.
Thanks
Gerald - KC6CNN
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KX3-amp-tuner-tp7556960.html
The amp most certainly will respond to the RF produced by the K2, but I
am not certain if the TUNE button will do the same as is done in the
K2/100. The K3 menu has provisions for Tune Power settings.
In other words, the amp will work fine, but your question about the 500
watt tuner will not
Don
That is for the little 100 watt amp coming for the KX3? Or were you talking
about the kpa500?
On Jun 1, 2012 7:36 PM, Don Wilhelm w3...@embarqmail.com wrote:
The amp most certainly will respond to the RF produced by the K2, but I
am not certain if the TUNE button will do the same as is done
Will the KX3 , have the PTT/Keying options as the Juma PA-100D amplifier ?
PTT out and or be able to key via the output coax ??
Thanks
Sid
KC2EE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Yes.
73,
Wayne
N6KR
On Jan 30, 2012, at 2:52 PM, Sid Leben wrote:
Will the KX3 , have the PTT/Keying options as the Juma PA-100D
amplifier ? PTT out and or be able to key via the output coax ??
Thanks
Sid
KC2EE
__
Elecraft
] [KX3 amp] 100/50
To: elecraft@mailman.qth.net
Message-ID: 4f1860a8.9000...@yahoo.com
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
The issue is regarding setting a MAXIMUM output limit. for Legal or
Safety reasons!
In both cases - where accidental QRO could
Subject: Re: [Elecraft] [KX3 amp] 100/50
To: elecraft@mailman.qth.net
Message-ID: 4f1860a8.9000...@yahoo.com
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
The issue is regarding setting a MAXIMUM output limit. for Legal or
Safety reasons!
In both cases - where accidental QRO
That would be good, since the intermediate license in the UK limits ops to 50w
too. A great way to buy a good rig for the future and remove the link when they
get the full license.
73 de David, M0XDF (K3 #174, P3 #108)
--
A child, like your stomach, doesn't need all you can afford to give it.
Wow! What a quick feed back.
This is Elecraft quality that we love :)
Thank you Wayne Elecraft.
73
Atsu, JE1TRV
Hi Atsu, Do you get 41 minute response from the chief designer at your local
radio manufacturers? !!!
No committees, no design review, no marketing studies, no
by
Elecraft.
TNX 73,
Johnny VR2XMC
從︰ Rick Stealey rstea...@hotmail.com
收件人︰ elecraft@mailman.qth.net
傳送日期︰ 2012年01月19日 (週四) 7:34 PM
主題︰ Re: [Elecraft] [KX3 amp] 100/50
Wow! What a quick feed back.
This is Elecraft quality that we love :)
Thank you
To be fair, if the sales volume of elecraft products is in line with those
major Japanese ham radio manufacturers, it will be very difficult for both
Wayne and Eric to maintain the existing response time.
I'm not worried. WHEN, (not IF) Elecraft sales volume exceeds the JA
manufacturers,
mode, NUE-PSK modem is my choice for PSK31. SCS pactor 3 modem
is for airmail and winlink.
TNX 73,
Johnny VR2XMC
從︰ Rick Stealey rstea...@hotmail.com
收件人︰ elecraft@mailman.qth.net
傳送日期︰ 2012年01月19日 (週四) 9:15 PM
主題︰ Re: [Elecraft] [KX3 amp] 100/50
A power limit switch would be fine, but I would still want to have a linear
control so that I could dial up my desired power level. Perhaps the limit
control could be menu selectible.
Dick, n0ce
__
Elecraft mailing list
Home:
I don't understand. With the K3/KPA500 there is no knob on the
KPA500 but if you want to change the power level you just turn the
power knob on the K3. The K3 can remember that level the next time
you return to that band if you wish. A power knob on the KPA500
would be redundant and
The issue is regarding setting a MAXIMUM output limit. for Legal or
Safety reasons!
In both cases - where accidental QRO could be consequential... Legally
or health-wise.
In my case, I limit max power for my children's sake! In JA and UK's
cases - there was a 50w Legal upper limit.
Can we expect to see the 100w amp before Christmas. I assume it will have
bandpass filters? Be about $500?
I believe that will be the only 100w amp for qrp rigs with filtered output so
it should be popular with other rigs as well.
73
Mike R
Sent from my spy ring
Amateur/Ham Radio KE5GBC
HF
From JA
I'd like to suggest Elecraft to prepare 50W version amp for KX3 since the
max.power allowed for prtable operation is 50W in JA.
Small internal swith to select 100/50W might be nice idea for that.
BTW
Thank you very much Elecraft for accepting direct order from JA.
Atsu, JE1TRV
Can we
Hi Atsu,
We could provide a jumper or switch in the KXPA100 to limit power to
50 watts.
Thanks for the suggestion.
73,
Wayne
N6KR
On Jan 18, 2012, at 5:06 PM, JE1TRV wrote:
From JA
I'd like to suggest Elecraft to prepare 50W version amp for KX3
since the
max.power allowed for prtable
Wow! What a quick feed back.
This is Elecraft quality that we love :)
Thank you Wayne Elecraft.
73
Atsu, JE1TRV
Hi Atsu,
We could provide a jumper or switch in the KXPA100 to limit power to
50 watts.
Thanks for the suggestion.
73,
Wayne
N6KR
On Jan 18, 2012, at 5:06 PM, JE1TRV
Is there an approximate weight on the KXPA100 PA ?
72/73,
K1NR
On Wed, 18 Jan 2012 17:47:20 -0800
Wayne Burdick n...@elecraft.com wrote:
Hi Atsu,
We could provide a jumper or switch in the KXPA100 to
limit power to
50 watts.
Thanks for the suggestion.
73,
Wayne
N6KR
On
Wayne, I like the idea; albeit for different reasons. I began
operating QRP on all my rigs for 4 special reasons My Hamlets - my
four children that are all licensed and formed their own club WK1RK. In
fact, my youngest son is now studying for an Extra upgrade (and he is 12
and the Net
Somewhere between 1 pound and 50 pounds.
Patience - we will have the details later. It will not alter the gas
mileage on your SUV., but it is not something to add to your backpack.
73,
Don W3FPR
On 1/18/2012 9:10 PM, Eugene Balinski wrote:
Is there an approximate weight on the KXPA100 PA ?
Absolutely. IMHO, a 3 position switch or jumper at the
power levels below would be ideal.
72/73
K1NR
On Wed, 18 Jan 2012 21:20:01 -0500
Phillip Nichols scotchma...@yahoo.com wrote:
Wayne, I like the idea; albeit for different reasons. I
began
operating QRP on all my rigs for 4 special
*FW switchable might work better?
Would hate to have to run around back of the motorhome to crank the power
up...especially if I am moving art the time...could be problematical?
Gary
*
On 19 January 2012 14:41, Eugene Balinski euge...@nni.com wrote:
Absolutely. IMHO, a 3 position switch or
92 matches
Mail list logo
