I just tried N1MM in SO2V mode using a K3 with Sub Receiver. Everything works
fine.
Now introduce RemoteRig. Connected to the remote K3 a thousand miles away,
when I press Control + Right Arrow Button to listen and move focus to VFO B/Sub
Receiver there is no audio from the sub receiver
I am afraid that this way you will get a lot of birdies originated from
KX3 itself. This is especially the case on 2m using an attached SMA
whip. Any other experience or info on the way tu cure this!?
73's.
Jacques F6AJW
Le 03/12/2014 23:48, Gerry leary a écrit :
I say, put batteries in the
Thanks for answers guys. Looks like it's nothing to worry about.
Jeff - kg7hdz
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Hi Vic,
With interest, I read your emails about the K3 QSK and the noise it produced
and I have a question for you. I've had my K3 for about three years and I
purchased it with a full complement of CW filters for both receivers,
including the 8-pole 250 hz filter. I normally run my radios in full
Hi,from Luigi,ik8ozz.
Take a look to : Morse Code Reader foe Android.
73
Message: 22
Date: Wed, 03 Dec 2014 19:55:51 -0800
From: Fred Jensen k6...@foothill.net
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Android App for CW
Message-ID: 547fdb47.4070...@foothill.net
Content-Type:
Tommy,
I have 8 pole filters for 400, 1000 and 2800 Hz. I am almost always using the
400 on CW. I use QRQ mode whenever possible. I found various sources of clicks
including bias switching in my amplifier, and a switched power source for my
Pixel Loop. I removed everything to isolate the
Hi again
Well this morning I checked all the coax connections all snug soldered
connections to g5rv window line intact
Re checked the K2/100 and KAT100
Here’s the results
no lights on SWR below 20M again variable output and SWR
SO…it turns out I have a faulty cable from the shack to the
The amplitude of this click depends on the amount of noise or signals
in the 'channel'. When listening to rx noise with no antenna, there's
no click. The worst case is a big pileup.
It would appear that the K3 is momentarily running at full gain when
returning from transmit, the click being
Experiencing the same thing with K3 #7167. Didn't know I had a problem as I
usually run my speaker out through an MFJ-784B digital filter because older
radios needed help, and the external filter cleans the artifacts nicely. My
K2 sounds better than my K3. I sold an Yaesu FT-2000 partly because
Vic Rosenthal k2vco@gmail.com wrote:
Turning down either the audio or RF gain helps with both artifacts, but makes
the output lower than desirable.
I talked to Wayne and Lyle a long time ago about possible ways to ameliorate
these noises and they had some ideas, but I haven't heard
Hi Wayne,
That would be great. I'm new to QSK and the various noises are distracting.
This past weekend in the CQ WW what I sometimes heard on 10 and 15 meters
was my own signal delayed. I assume that was a globe circling echo. I don't
suppose there would be a firmware solution for that
Free. It will send the name if the caller is in my phone book,
otherwise it sends the number.
Yes, but on my Samsung GT-I9100 'phone it's very distorted, except the
first character, I cannot control the volume and set this as default
ringtone...
And it's not free it cost me 69 eurocents
Did you QSL yourself? If you do that from 100 or more different countries
you can qualify for the WAY (Worked All Yourself) certificate.
Certain factions are laying the groundwork for that award in anticipation
of the inexorable rise in remote operations looming. It is inspired by a
certain
There seems to be unanimous agreement here, but I beg to differ. In my
opinion, the KX3 is not ideal for a typical beginning general class
operator. I own a KX3 myself, and I think it's wonderful, and I doubt that
I will ever part with it. It shines when it comes to portable operation ..
Good morning group. Well time for my request again to Elecraft. Could we
please see some firmware update to the P3. Now that the KX3 project is up and
running perhaps we could finish the P3 project. I personally would like to see
the noise blanker applied to the SVGA and some scrolling
That is great to hear Wayne! Keep up the good work and thanks for such a
great product/support!
de ns9i
On 12/4/2014 9:42 AM, Wayne Burdick wrote:
Vic Rosenthal k2vco@gmail.com wrote:
Turning down either the audio or RF gain helps with both artifacts, but makes
the output lower than
You also will want to edit some contact names to something shorter.
There are options to use Morse only on selected contacts which is a lot
more convenient for me.
I don't worry about stares in the checkout. I just say, Sorry, I'm on
call, and move to the head of the line.
Eric
KE2US
On
I second that emotion (sic).
Sent from my Verizon Wireless 4G LTE smartphone
div Original message /divdivFrom: zumbr...@comcast.net
/divdivDate:12/04/2014 11:52 AM (GMT-05:00) /divdivTo: Elecraft
Reflector elecraft@mailman.qth.net /divdivSubject: [Elecraft] P3 UPDATE
I have heard that the configuration of AFSK TX - FIL ON/FIL OFF affects
afsk transmitted by feeding computer sound card generated afsk audio
tones. The entry in the manual seems to indicate the filter is only
active on afsk generated by the K3 internal afsk capability.Which is
correct?
Joe,
I think you are exactly correct! It does happen with 'key up' or between words
and it seems to last for only a few seconds at the most. But it is very
objectionable to listen to for many hours during contest.
Thanks for your observation and input!
73,
Tom - W4BQF
-Original
No, AGC on/off has no effect.
On 4 Dec 2014 17:00, Joe Subich, W4TV wrote:
The amplitude of this click depends on the amount of noise or signals
in the 'channel'. When listening to rx noise with no antenna, there's
no click. The worst case is a big pileup.
It would appear that the K3 is
I must admit, my experience was quite different. I started as a
tech doing mostly 2M repeater contacts. When I upgraded my
license, I had an Icom 706M2G which I used with full size
dipoles. I discovered PSK31 at field day and started using the
Icom at QRP levels making many contacts on 20, 40,
The entry in the manual seems to indicate the filter is only
active on afsk generated by the K3 internal afsk capability.
The K3 does not generate AFSK internally. AFSK is only transmitted
in response to external audio.
73,
... Joe, W4TV
On 2014-12-04 12:41 PM, Dave Barr wrote:
I
One of the pieces of advice for operating the K3, is to use the minimum
amount of gain in the RF/IF string. This is done by setting ATT/PRE/RF gain
so that there is only a moderate amount of band noise with no signal, then
setting audio for a comfortable level on signals with AGC engagement. This
Having heard stories like this hundreds of times over the years, why do we
start by thinking the radio is broken? :)) Wish I had a buck for every
post here complaining about radio gear that wound up completely external to
K2, K3, KATxxx, etc. In some cases it was a really hard sell to get the
I have a K2 with the external twin at/100 and pa/100.
My external 100 watt amp and tuner is controlled by the serial cable coming off
the radio.
I want to someday get a K3 and was wondering if the k3 would be able to control
the external amp/tuner combo I currently have with my K2??
Thanks
Unfortunately the K2 KPA100/KAT100 will only work with the K2. For the K3
you'll need to get the KPA3/KAT3 modules, or possibly get an external amp such
as KXPA100/KXAT100 that can be used with both K2and K3 (albeit not as fully
integrated as the dedicated amplifier/ATU options for each radio).
Nope. The six non-serial-port leads in that cable are K2 internal leads
very specific to the K2.
73, Guy
On Thu, Dec 4, 2014 at 2:18 PM, Tim Edmonson timedmon...@spfs.net wrote:
I have a K2 with the external twin at/100 and pa/100.
My external 100 watt amp and tuner is controlled by the
Hmmm, both work fine on my Samsung Galaxy 5, volume works fine, they're
my default ring tones. Both were free, but I've had them for quite
awhile now. I wish SMS2CW looked in the phone book. I know phone
numbers for wife, kids, and grandkids, but for others, the CW just lets
me know that
I am using RemoteRig with K3 Twins. I want to use N1MM and SO2V. Everything
works as advertised except when you choose to change the focus from VFO 1 to
the sub receiver or VFOB the audio from the sub receiver is dead until you
slightly move the AF gain knob for the sub receiver. It works
Nor do I. ATT=ON/PRE=OFF on 160, 80, and 40 unless 40 is unusually
quiet. Then I might set ATT=OFF [not common], ATT=OFF/PRE=OFF on 20,
ATT=OFF/PRE=ON on 10, and sometimes PRE=ON on 15 [also not common]. I'm
about 90% CW, I run QSK no QRQ most of the time, QRQ in contests.
Paddle is on the
I tried several of these apps, but none of them really did what I wanted. I
finally recorded a separate ringtone for each person I wanted by using the
Samsung Voice Recorder on my Galaxy S5. I used the sidetone from my KX3 and a
CW Touch Keyer to eliminate “paddle clatter”. I suppose you
Hi folks.
Just obtained a KX1. Covers the four bands, with built-in ATU and
paddles. I've already had fun with it.
I can't seem to bring upn the the firmware version by pressing a switch
while powering up? What am I doing wrong?
Also, the encoder seems a tad loose. It works perfectly
John,
If your KX1 has 4 bands, you have firmware 1.02 - it is required to
support 80 meters.
That is also the latest firmware revision.
There was a change in the encoder used in the KX1 a while back. The new
one has a tighter 'feel' to it. You might want to consider changing
it. The
I generated some nice sounding cw mp3's for my ringtone using this site:
http://www.morseresource.com/morse/makemorse.php
Eric,
WB7SDE
On Thu, Dec 4, 2014, at 12:56 PM, Eric Ross wrote:
I generated some nice sounding cw mp3's for my ringtone using this site:
On 12/4/2014 11:12 AM, Guy Olinger K2AV wrote:
Is that because the radio is in front of us and has lights on, and
therefore is what our eyes fasten upon? Or are we really that
pre-disaffected with our radios?
Probably neither. It seems to be basic human nature to assume the
worst. Kid is
I estimate that something over 90% of all the problems I have had with rigs
over the years not performing up to spec came from from bad coax and
connector installation. That's the first thing I suspect now. Goofy tune
up, weird SWR readings, lo-no output, poor signal reception, hair loss and
I gave up on it :-(
Gary
Vk1ZZ
K3, KX3, KPA500-FT, KAT500-FT,P3.
On 05/12/2014 3:36 AM, hsherriff hsherr...@reagan.com wrote:
I second that emotion (sic).
Sent from my Verizon Wireless 4G LTE smartphone
div Original message /divdivFrom:
zumbr...@comcast.net
On 04/12/14 18:20, Joe Subich, W4TV wrote:
The K3 does not generate AFSK internally. AFSK is only transmitted
in response to external audio.
But that is exactly how SDR architecture transmitters do generate FSK.
The only difference from what is popularly called AFSK is that the tone
starts
Hi Folks,
I brought my K3 to Florida for the winter. I turned it on and it won't TX
RX is fine except for the QRN nothing I can do about that.
Any ideas for the TX problem?
--
73
KI4TXP JAY
__
Elecraft mailing list
Home:
While the K3 is an SDR, it generates FSK Mark and Space tones directly
at IF. There is no digitizing of audio tones from the input and
numerically mixing them to IF and filtering (or numerically cancelling)
the unwanted products.
The fact that the tones are created in response to a DC control
Is it in test mode?
73
K2TTT (Jay)C6ATT
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of JAY
Sent: Thursday, December 04, 2014 7:36 PM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] K3 won't TX
Hi Folks,
I brought my K3 to Florida for the
Hello,
I'm trying to get on PSK31 with a new Windows 7 64-bit computer. I've read the
owner's and Cady manuals, checked and re-checked the settings and still no joy.
The setup is the K3, ASUS Xonar U7 external sound card, microKEYER interface
and FLdigi. Basically I have no power output and no
In the case of the K3, the FSK mode uses DSP-generated IF frequencies in
the 15 kHz range for the Tx, and simultaneously creates audio tones at
the selected pitch-pair.
In AFSK mode, the radio requires that you supply audio to a Mic
connector or the Line In connector. The AFSK Tx filter may
Not sure what you mean by won't TX but a couple of things you might check:
-- is it in TX Test mode
-- is the proper antenna selected. K3's won't make RF into an open
circuit. You can ask me how I know that, a humbling experience with
Wayne on the phone
-- If you're on CW, is VOX on?
--
And check the TX INH if you've been messing around in the Config Menu.
73 charlie, k1xx
On 12/4/2014 8:35 PM, Fred Jensen wrote:
Not sure what you mean by won't TX but a couple of things you might
check:
-- is it in TX Test mode
-- is the proper antenna selected. K3's won't make RF into
Have you followed the Setting Audio Levels section of the
microKEYER Users manual *exactly*?
73,
... Joe, W4TV
On 2014-12-04 8:24 PM, w3sb wrote:
Hello,
I'm trying to get on PSK31 with a new Windows 7 64-bit computer. I've read the
owner's and Cady manuals, checked and re-checked the
Please keep me signed in to the Elecraft Digest.
72/73's
Robert Reiman Kb9iva
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
I just finished assembling my new KX3 yesterday and I'm not sure if the
real-time clock is working correctly. I set the time, but when I turn off
the rig and turn it back on it's set to a completely different time. Am I
missing something?
Jock, N1JI
Did you install battery charger/batteries and enable it?
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KX3-Clock-Not-Keeping-Time-tp7595484p7595485.html
Sent from the Elecraft mailing list archive at Nabble.com.
That is why I first ask how the transceiver behaves when connected to a
dummy load.
Even that is not conclusive because there is always the possibility of a
faulty coax between the transceiver and the dummy load, but it does
usually rule out a fault in the transceiver and force attention to the
Monty,
You apparently do not have enough audio going into the K3.
You mention an external soundcard as well as a microKEYER interface (the
microKEYER does include an external soundcard).
So do you have the correct soundcard specified in your software
application(s) and is that soundcard
David and all,
I would beg to differ, AFSK starts as external audio tones into an SSB
transmitter.
How those tones are modulated into an RF signal is not dependent on
whether the transceiver is DSP or analog, the output should be the
same. It may be digitized in the middle of the
Yes, and I've tried disabling/Enabling it a few times. Whenever I turn the
radio on, the clock starts at 00:68:00 then the seconds count up to 00:69:00.
After another minute it's at 01:00:00 and it goes on from there.
Thanks
Sent from my iPhone
On Dec 4, 2014, at 10:16 PM, Bob N3MNT
Do you have batteries installed in your KX3?
If not, there is no power to keep the time clock running when you power
the KX3 off.
73,
Don W3FPR
On 12/4/2014 10:58 PM, Jock Irvine wrote:
Yes, and I've tried disabling/Enabling it a few times. Whenever I turn the
radio on, the clock starts at
Did you install the battery charger option? You need this to keep time
Original message
From: Jock Irvine [via Elecraft] ml-node+s365791n7595484...@n2.nabble.com
Date:12/04/2014 18:42 (GMT-08:00)
To: KD6QZX kd6...@sbcglobal.net
Subject: KX3 Clock Not Keeping Time
I
56 matches
Mail list logo