Re: [Elecraft] Picture of 3 by 5 card solution for K Pod cheat sheet

Hi Don, This is sent via Nabble. You'll see your posting below as a quote. The Quote button is very visible above the text area to the left. The quote is easy to trim. I find Nabble very convenient for responding to messages. AB2TC - Knut Don Wilhelm wrote > Because many read the posts on

Re: [Elecraft] K3S fsk with usb

Hi Peter, Using a regular/cheap USB <> RS232 converter and NPN-"interface" to the ACC port. FSK works fine here with my K3s. MMTTY settings: TX menu : port = EXTFSK64 Misc menu : tx-port = Com-TxD(FSK) , click USB and set C where needed Audio via USB. Henk PA0C PS, kan jammer genoeg niet met

Re: [Elecraft] K3S fsk with usb

This thread is running parallel to a discussion running on the DXLabs reflector today, due to the release of a new MMTTY FSK interface to TinyFSK programmed by Oba JA7UDE. I'll apologize in advance for inserting the following: I'd like to avoid having my response drag this thread into

Re: [Elecraft] K3S fsk with usb

Brian, My first response would be "use AFSK". My second would be "use a TinyFSK for FSK". But in response to your question, if you really want to key FSK directly from a USB-to-serial adapter you can use the EXTFSK plugin in MMTTY (). This works with any

[Elecraft] Pig Knob for sale

Has VFO and 8 programmable buttons (poor man's K-Pod). In excellent condition - hardly used - shipped to your door in the lower 48 for $35.00. Address good in QRZ. Mike W9RE __ Elecraft mailing list Home:

Re: [Elecraft] K3S fsk with usb

Rich, I seem to recall that the serial port needed for FSK generally cannot come from the run of the mill USB/RS232 converters. They can't operate at 45 baud/5 bit rate needed. See: http://aa5au.com/GettingStartedOnRtty.pdf This is old info and things may have changed. So what does a guy

[Elecraft] Picture of the 3 x 5 card label solution

Ok, ios12 and iCloud put the pictures on this link: https://share.icloud.com/photos/0aNIqRlH8m9F8ZeHC2ArfYLNg#Home Chuck KE9UW Sent from my iPhone, cjack __ Elecraft mailing list Home:

Re: [Elecraft] [K3 Remote] TERM Mode no longer persists?

I've experienced this several times Rick. Once, it was because I had dismantled my control setup and when I reassembled it, I forgot to use the null modem cable between the K3 and RRC.  The other times [three maybe], it's been a bad RS-232 DE-9 connection at the RRC.  I think it is only one

[Elecraft] FS: K-Pod

K-Pod in excellent condition - hardly used - shipped to your door in the lower 48 for $180.00. Postal MO or PayPal only. Address good in QRZ. Bill W2BLC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft

[Elecraft] K3S fsk with usb

Hello list, I want to do FSK with my K3S. N1MM and MMTTY. The USB cable i used it for radio control. What kind of cable do i need for FSK or can i used the USB cable also. Any suggestions are welcome. 73s Peter/pd1rp __ Elecraft mailing

[Elecraft] FS: Pig Knob for K3

Has VFO and 8 programmable buttons (poor man's K-Pod). In excellent condition - hardly used - shipped to your door in the lower 48 for $35.00. Postal MO or PayPal only. Address good in QRZ. Bill W2BLC __ Elecraft mailing list Home:

Re: [Elecraft] FS: K-Pod

Has been sold. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support

Re: [Elecraft] FS: K-Pod SOLD

Sold __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email

[Elecraft] [K3 Remote] TERM Mode no longer persists?

I seem to be suffering a recurrence of a very old problem (years ago) for which I don't recall the solution: I have a real K3 at the control site, controlling a K3 at the remote site via RRC-1258 MkII boxes. I have a mechanical D-SUB 9 pin switch to route the control site K3 serial port to either

Re: [Elecraft] FS: Pig Knob for K3 SOLD

Sold __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email

Re: [Elecraft] K3S fsk with usb

Peter, You will have to gain access to the RS-232 DTR or RTS signals. If you do not have the P3, you can insert the RJ45 to serial port dongle and pick the signals from that connector. Although I have not tried it, I believe it will work. You will also need to use a "one transistor keying

Re: [Elecraft] K3S fsk with usb

I agree with Don, why not do AFSK and eliminate all the extra hardware and cables?  No one except you will know the difference. 73 Bob, K4TAX On 8/30/2018 12:20 PM, Don Wilhelm wrote: Peter, You will have to gain access to the RS-232 DTR or RTS signals. If you do not have the P3, you can

[Elecraft] KPA500 in Operate when powered on

I have two KPA500 amplifiers that I use with a remote station. Both have the latest firmware.  I have these configured to go into Operate mode when powered on, however I have many issues getting this setting to "stick". In other words, when remotely powered on, they come up in Standby despite

Re: [Elecraft] Picture of the 3 x 5 card label solution For K-POD switches

Thanks, Chuck. I added to topic to aleve the topic concerns. Like the simplicity. When I don't use a particular switch often enough, I forget what it is for. When I programmed and when I remember can be quite distant in time. 73, Bill K9YEQ https://wrj-tech.com/ -Original

Re: [Elecraft] K3S fsk with usb

To transmit FSK from N1MM+/MMTTY with a K3 or K3S, you need: (a) some kind of serial port-based keying interface; and (b) a cable from the keying interface to the 15-pin ACC port on the back of the K3/K3S (pin 1 is the FSK keying input). The serial port used for FSK keying by MMTTY must be a

Re: [Elecraft] [K3 Remote] TERM Mode no longer persists?

Hey Rick, The TERM message should always be transitory. If it is not, you have an RS-232 control problem (like the null-modem issue). Check all your cables. In 100% of the times I've seen this issue, it's a loose connector or a mismatched cable 73 Gerry Hull, W1VE Hancock, NH USA Trustee,

Re: [Elecraft] K3S fsk with usb

I have a RigExpert TI-8 and Cable for the K3S that I bought new that does FSK with a built in Winkeyer as well. I thought I would use it on the K3S but instead I just went the USB route and do AFSK. It's still setting in the box looking lonely. I also have cables for the Ten Tec Orion II, and

Re: [Elecraft] K-POD labels

Thanks for that infor, Eric. Won't bother with P-Touch for that. 73, Bill K9YEQ https://wrj-tech.com/ -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Eric Rosenberg Sent: Thursday, August 30, 2018 8:39 PM To: elecraft@mailman net Subject: Re: [Elecraft] K-POD

Re: [Elecraft] K3S fsk with usb

Yes the S-BOX is designed to key FSK and PTT on a K3 ACC port, providing the traditional NPN keying circuit, with no Y-BOX required (though it may be convenient to have as well, depending on what else you need to connect to the K3 ACC port). Straight 9-pin and 15-pin D-SUB cables handle

Re: [Elecraft] K3S fsk with usb

I believe that FSK uses the TX signal on a serial port and is connected to a pin on the DE15 ACC2 port on the K3(S). Sent from my iPhone ...nr4c. bill > On Aug 30, 2018, at 2:19 PM, Richard Ferch wrote: > > To transmit FSK from N1MM+/MMTTY with a K3 or K3S, you need: (a) some kind > of

Re: [Elecraft] K-POD labels

Brother P-Touch labels fit between the K-POD function buttons. The best is TZ-211, 6 mm (1/4"). The next larger size, TZ-221, 9mm, (3/8") is just a hair too tight for me. Both are black print over a white background (which covers the F Key label on the K-POD. There are lots of choices of both

Re: [Elecraft] K3S fsk with usb

I went a similar route with a MicroKeyer MK-II. Does the job very well, but it makes disconnecting and re-connecting the radio a cast iron bear of a job. I really want to replace the MK-II with another (simpler) solution for FSK, CW keying, SSB voice file sequencing and CAT control, and was

Re: [Elecraft] K-POD labels

Thanks Fred. I will try this way. 73, Ian IK4EWX -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

Re: [Elecraft] K2 power setting issue

Chris, Which flavor K2 do you have? Base K2 only Base K2 with KAT2 K2 with KPA100 installed The bottom line is that there is no indication of power output being fed back to the MCU on the VRFDET line, so the MCU tries to ramp up power to produce more output - and it will go to its maximum

Re: [Elecraft] K-POD labels

Mike, where is available to buy this thin magnetic strip? Thanks Ian IK4EWX -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] Picture of 3 by 5 card solution for K Pod cheat sheet

I only show one side to satisfy KB limitation. Chuck KE9UW Sent from my iPhone, cjack __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] K2 power setting issue

My second K2 has some issue with output power. The power is set at 1.0W but is measured at over 10W at the dummy load. When I set the power to a little higher, I get 'Hi Cur' message but it goes away after a second. CAL CUR is set at 2.5A, and the modulation seems OK when I hear from other

Re: [Elecraft] Bizarre K2 keyer issue

FYI, I had a very similar issue last month, I keyed down and I got an error code on the display, I cant remember exactly what one it was but it wasn’t listed in the manual. Anyway, all I done was took the key plug out and reseated it and all was well again. I suspect a high resistance

Re: [Elecraft] K-POD labels

Thanks Dwight. I thought to use a single adesive sheet but your solution is sure easier. 73, Ian IK4EWX -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft

Re: [Elecraft] Picture of 3 by 5 card solution for K Pod cheat sheet

Because many read the posts on Nabble and it is difficult to add a bit of information to indicate what they are referring to. Those posters might just as well talk into the wind, without context for reference, the subject line is not sufficient. Same with call signs shown in your email

Re: [Elecraft] K-POD labels

Chuck, this solution is in line with my first opinion. In the past I used on a home made superkeyer III a transparent adhesive sheet that I printed with a laser printer, with black characters, with great result. Here the problem is the black face of KPOD. It should be a clear and not

Re: [Elecraft] Picture of 3 by 5 card solution for K Pod cheat sheet

Sorry, I guess pictures are not allowed Chuck Jack KE9UW Sent from my iPhone, cjack > On Aug 30, 2018, at 8:37 AM, hawley, charles j jr > wrote: > > > > I only show one side to satisfy KB limitation. > > Chuck > KE9UW > > Sent from my iPhone, cjack >

Re: [Elecraft] Picture of 3 by 5 card solution for K Pod cheat sheet

Why all these posts lacking context? Sent from my iPad > On Aug 30, 2018, at 6:36 AM, hawley, charles j jr > wrote: > > > > I only show one side to satisfy KB limitation. > > Chuck > KE9UW > > Sent from my iPhone, cjack > __ >