Re: [MBZ] Replacing W140 Motor Mounts
Sharpie marks with anything I replace on the car with the mileage and date, when space permits. If you pul a filter on one of my cars it will have the mileage it was installed at and the date. And it gets entered in the database with date, time, cost and part information. Example from the S500: Service 0 3/20/13 8:40 PM 1995 Mercedes-Benz S500 246,895 $0.00 0 $74.47 HomeDebit 0 $74.47 Replace transmission mount Gas 17.73/16/13 1:03 PM 1995 Mercedes-Benz S500 246,742 Full$3.81 13.258 $50.50 90+ Sam's Club Brandon, FL Debit 0 $50.50 Service 0 3/14/13 2:00 PM 1995 Mercedes-Benz S500 246,670 $0.00 0 $24.00 HomeDebit 0 MB power steering fluid $24.00 Flush & fill power steering, Replace power steering filter Service 0 3/13/13 3:06 PM 1995 Mercedes-Benz S500 246,618 $0.00 0 $165.00 HomeDebit 0 $165.00 Replace motor mounts Service 0 3/12/13 5:56 PM 1995 Mercedes-Benz S500 246,602 $0.00 0 $181.84 Tint Studio, Gibsonton, FL Debit 0 $181.84 Window tinting Service 0 3/11/13 7:28 PM 1995 Mercedes-Benz S500 246,590 $0.00 0 $100.00 HomeDebit 0 Mobil 1 gear oil, MB coolant @ 30%, Purple Ice cooling system additive $100.00 Antifreeze, Flush cooling system, Add cooling system treatment, Drain & refill differential, Replace thermostat Gas 15.33/8/13 4:10 PM 1995 Mercedes-Benz S500 246,539 Full$3.87 16.412 $63.50 90+ Sam's Club Brandon, FL Debit 0 $63.50 Service 0 3/6/13 5:57 PM 1995 Mercedes-Benz S500 246,453 $0.00 0 $21.00 HomeDebit 0 $21.00 Install body drain grommets, Install trunk drain grommets, Windshield Wipers Gas 17.73/1/13 5:42 PM 1995 Mercedes-Benz S500 246,249 Full$4.02 14.431 $58.00 90+ HessBloomingdaleDebit 0 $58.00 Service 0 2/24/13 5:00 PM 1995 Mercedes-Benz S500 246,028 $0.00 0 $0.00 HomeDebit 0 $0.00 Clean connections on instrument cluster connectors and circuit board Service 0 2/24/13 2:00 PM 1995 Mercedes-Benz S500 246,012 $0.00 0 $38.50 HomeDebit 0 $38.50 Flush SLS system and replace filter screen Service 0 2/24/13 10:32 AM1995 Mercedes-Benz S500 246,007 $0.00 0 $15.00 HomeDebit 0 $15.00 Fuel Filter Service 0 2/23/13 5:00 PM 1995 Mercedes-Benz S500 246,000 $0.00 0 $100.00 HomeDebit 0 $100.00 Replace front flex disc, Replace rear flex disc Gas 18 2/22/13 4:12 PM 1995 Mercedes-Benz S500 245,989 Full$3.99 19.052 $76.00 90+ Sam's Club Brandon, FL Debit 0 $76.00 Service 0 2/17/13 2:00 PM 1995 Mercedes-Benz S500 245,771 $0.00 0 $36.00 HomeDebit 0 $36.00 Clean interior, Replace third brake light cover, Cabin air filter Gas 17.52/13/13 4:25 PM 1995 Mercedes-Benz S500 245,656 Full$3.80 18.031 $68.50 90+ Sam's Club Brandon, FL Debit 0 $68.50 Service 0 2/11/13 8:27 PM 1995 Mercedes-Benz S500 245,586 $0.00 0 $42.00 HomeDebit 0 $42.00 Cabin air filter, Replace ACC panel lamps, Replace water temp gauge sender, Replace third brake light bulb Service 0 2/8/13 1:00 PM 1995 Mercedes-Benz S500 245,580 $0.00 0 $397.40 Tampa, FL Check 0 $397.40 Registration, Title Service 0 2/7/13 5:33 PM 1995 Mercedes-Benz S500 245,451 $0.00 0 $508.90 Brandon, FL Debit 0 $508.90 Replace front tires, Replace rear tires Service 0 2/6/13 3:52 PM 1995 Mercedes-Benz S500 245,403 $0.00 0 $342.00 HCPSDebit 0 $342.00 Windshield replacement Gas 17.72/4/13 5:53 PM 1995 Mercedes-Benz S500 245,337 Full$3.73 21.99 $82.00 90+ Sam's Club Brandon, FL Debit 0 $82.00 Service 0 2/2/13 7:00 PM 1995 Mercedes-Benz S500 245,255 $0.00 0 $0.00 BloomingdaleDebit 0 $0.00 Wax, Wash Gas 20.42/1/13 5:06 PM 1995 Mercedes-Benz S500 244,888 Full$3.90 17.481 $68.16 90+ Shell Savannah, GADebit 0 $68.16 > On Sep 5,
Re: [MBZ] Replacing W140 Motor Mounts
The lumbar bladder, NOT the orthopedic one that has like 5 different sections, is a piece of cake to replace. You can do it through the back cover, which comes off with a couple of screws at the bottom and then just pulling down to remove it. With the back cover off you can see the old one. There is a foam pad that’s stuck to the bladder with plastic rivets, you want to keep that on the new one when you slip it into place. I just cut the pneumatic line and splice it. I’ve snaked the new line and connector with the convoluted tubing on it through the seat hinge but it’s a PITA to do. Pretty simple. The bladder is about $60 list. If by chance you have the orthopedic seats, you’re screwed. The bladder for the orthopedic seat is NLA, and even if it was available it cost about $250. Dan > On Sep 5, 2015, at 11:46 AM, Kaleb C. Striplin via Mercedes > wrote: > > What's the deal with the seat bladders? I think I have leaking ones on mine. > How hard are they to replace? > > Sent from my iPhone > >> On Sep 5, 2015, at 10:06 AM, Dan Penoff via Mercedes >> wrote: >> >> Thanks! >> >> I hoping to put an end to the pneumatic issues that I have discovered that >> appear to have plagued this car for years. I spent a while studying all of >> the records last night, including the complete history from the MB >> dealership where it was purchased and maintained for the first ten years of >> its life. >> >> It’s had a grand total of four PSE pumps replaced over the years. Right >> now, the locks work, and the lumbar bladders would work (one is leaking due >> to age) but the back up aids don’t extend. Fuel mileage is marginal as >> well, so I’m almost positive there’s a vacuum leak in the system, too. >> >> If you’re not familiar with the PSE pump in the 90s models, it provides both >> vacuum and pressure for door locks, AC flaps, lumbar bladders and in the >> case of the W140 from 92-95, these little “antennae” or “sticks” that extend >> out of the tops of the rear fenders when the car is in reverse so you know >> where the corners of the car are. Mercedes refers to them as “back up aids.” >> >> The PSE works with engine vacuum in the sense that if engine vacuum to the >> system drops below a certain point the PSE will kick in to help out. This >> allows AC flaps to work when the engine is not running, primarily for the >> ACC’s “REST” function (heat available after the car is shut off.) >> >> There is a vacuum distribution block in the passenger front footwell that is >> prone to leak and often overlooked. I have a new one on order, as they’re >> cheap, but I’ll be testing this one today as I suspect that’s where the >> problem lies. The giveaway is the loss of AC flaps when engine vacuum drops >> due to acceleration. The PSE pump isn’t able to keep up and the vacuum >> drops, causing the flaps to go to the default (defrost) position. >> >> It’s pretty amazing looking back over the records on this car. I’m thinking >> the independent they used for the last ten years had a big boat, or a kid >> they needed to put through college. >> >> In less than 80,000 miles, the car has had the following replaced: >> >> Starter >> Alternator >> Power steering pump (2x) >> AC compressor (2x) >> AC evaporator (2x) >> AC condensor (2x) >> Ignition lock cylinder (2x) >> PSE pump (4x) >> >> It was like clockwork when they would have the car in for service with the >> independent and it would need some sort of major work. >> >> Dan >> >> >> >>> On Sep 5, 2015, at 10:50 AM, Craig via Mercedes >>> wrote: >>> >>> >>> I wish you success! >>> >>> >>> Craig >>> >>> ___ >>> http://www.okiebenz.com >>> >>> To search list archives http://www.okiebenz.com/archive/ >>> >>> To Unsubscribe or change delivery options go to: >>> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >> >> >> ___ >> http://www.okiebenz.com >> >> To search list archives http://www.okiebenz.com/archive/ >> >> To Unsubscribe or change delivery options go to: >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >> > > ___ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
On Sat, 05 Sep 2015 13:40:27 -0400 Dan Penoff via Mercedes wrote: > I add to it with the mileage of the car…. Interesting idea! Craig ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
I’ve seen all sorts of letters on Lemforder stuff. I can only suspect that it’s a QC think, maybe the inspector that checks it before it goes out the door? I add to it with the mileage of the car…. Dan > On Sep 5, 2015, at 1:20 PM, Max Dillon via Mercedes > wrote: > > Yes. > > "BBB" on the new mount = Better Business Bureau? > -- > Max Dillon > Charleston SC > '87 300TD > '95 E300 > > On September 5, 2015 12:03:45 PM EDT, Dan Penoff via Mercedes > wrote: >> Thanks, Wilton. >> >> Think the mounts were collapsed? >> >> https://www.dropbox.com/s/55y7cu2l0ymwlof/IMG_0846.jpg?dl=0 >> >> >> Dan >> >> >>> On Sep 5, 2015, at 11:45 AM, WILTON via Mercedes >> wrote: >>> >>> ATTABOY! >>> >>> Wilton >> >> >> ___ >> http://www.okiebenz.com >> >> To search list archives http://www.okiebenz.com/archive/ >> >> To Unsubscribe or change delivery options go to: >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > ___ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
Yes. "BBB" on the new mount = Better Business Bureau? -- Max Dillon Charleston SC '87 300TD '95 E300 On September 5, 2015 12:03:45 PM EDT, Dan Penoff via Mercedes wrote: >Thanks, Wilton. > >Think the mounts were collapsed? > >https://www.dropbox.com/s/55y7cu2l0ymwlof/IMG_0846.jpg?dl=0 > > >Dan > > >> On Sep 5, 2015, at 11:45 AM, WILTON via Mercedes > wrote: >> >> ATTABOY! >> >> Wilton > > >___ >http://www.okiebenz.com > >To search list archives http://www.okiebenz.com/archive/ > >To Unsubscribe or change delivery options go to: >http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
Thanks, Wilton. Think the mounts were collapsed? https://www.dropbox.com/s/55y7cu2l0ymwlof/IMG_0846.jpg?dl=0 Dan > On Sep 5, 2015, at 11:45 AM, WILTON via Mercedes > wrote: > > ATTABOY! > > Wilton ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
What's the deal with the seat bladders? I think I have leaking ones on mine. How hard are they to replace? Sent from my iPhone > On Sep 5, 2015, at 10:06 AM, Dan Penoff via Mercedes > wrote: > > Thanks! > > I hoping to put an end to the pneumatic issues that I have discovered that > appear to have plagued this car for years. I spent a while studying all of > the records last night, including the complete history from the MB dealership > where it was purchased and maintained for the first ten years of its life. > > It’s had a grand total of four PSE pumps replaced over the years. Right now, > the locks work, and the lumbar bladders would work (one is leaking due to > age) but the back up aids don’t extend. Fuel mileage is marginal as well, so > I’m almost positive there’s a vacuum leak in the system, too. > > If you’re not familiar with the PSE pump in the 90s models, it provides both > vacuum and pressure for door locks, AC flaps, lumbar bladders and in the case > of the W140 from 92-95, these little “antennae” or “sticks” that extend out > of the tops of the rear fenders when the car is in reverse so you know where > the corners of the car are. Mercedes refers to them as “back up aids.” > > The PSE works with engine vacuum in the sense that if engine vacuum to the > system drops below a certain point the PSE will kick in to help out. This > allows AC flaps to work when the engine is not running, primarily for the > ACC’s “REST” function (heat available after the car is shut off.) > > There is a vacuum distribution block in the passenger front footwell that is > prone to leak and often overlooked. I have a new one on order, as they’re > cheap, but I’ll be testing this one today as I suspect that’s where the > problem lies. The giveaway is the loss of AC flaps when engine vacuum drops > due to acceleration. The PSE pump isn’t able to keep up and the vacuum > drops, causing the flaps to go to the default (defrost) position. > > It’s pretty amazing looking back over the records on this car. I’m thinking > the independent they used for the last ten years had a big boat, or a kid > they needed to put through college. > > In less than 80,000 miles, the car has had the following replaced: > > Starter > Alternator > Power steering pump (2x) > AC compressor (2x) > AC evaporator (2x) > AC condensor (2x) > Ignition lock cylinder (2x) > PSE pump (4x) > > It was like clockwork when they would have the car in for service with the > independent and it would need some sort of major work. > > Dan > > > >> On Sep 5, 2015, at 10:50 AM, Craig via Mercedes >> wrote: >> >> >> I wish you success! >> >> >> Craig >> >> ___ >> http://www.okiebenz.com >> >> To search list archives http://www.okiebenz.com/archive/ >> >> To Unsubscribe or change delivery options go to: >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > > > ___ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
On Sat, 05 Sep 2015 11:06:14 -0400 Dan Penoff via Mercedes wrote: > Thanks! You are welcome. > I hoping to put an end to the pneumatic issues that I have discovered > that appear to have plagued this car for years. > > There is a vacuum distribution block in the passenger front footwell > that is prone to leak and often overlooked. I have a new one on order, > as they’re cheap, but I’ll be testing this one today as I suspect > that’s where the problem lies. The giveaway is the loss of AC flaps > when engine vacuum drops due to acceleration. The PSE pump isn’t able > to keep up and the vacuum drops, causing the flaps to go to the default > (defrost) position. May it solve your problems! > In less than 80,000 miles, the car has had the following replaced: > > Starter > Alternator > Power steering pump (2x) > AC compressor (2x) > AC evaporator (2x) > AC condensor (2x) > Ignition lock cylinder (2x) > PSE pump (4x) > > It was like clockwork when they would have the car in for service with > the independent and it would need some sort of major work. That's pretty amazing. I agree; the independent had either a boat or a child he needed to put through college. Craig ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
ATTABOY! Wilton - Original Message - From: "Dan Penoff via Mercedes" To: "Okie Benz" Cc: "Dan Penoff" Sent: Saturday, September 05, 2015 10:46 AM Subject: [MBZ] Replacing W140 Motor Mounts Just finished this job, second time I’ve done it, first time was on the S500 coupe, this time on the 1994 S420. I bought the special offset wrench for removing the top mount bolt, as it’s buried under the manifolds. Best $15 I ever spent for a special tool for this job. It made it go much faster. I did the passenger (easy) side in about 20 minutes, the driver’s side (difficult) in about 40. Now I’m heading back out to put the transmission mount in. Pretty easy job on the W140. I’m getting the nasty stuff out of the way early today, then it’s time to spend sorting out the pneumatics. Tomorrow it will be R&R of the right front caliper on the oldest boy’s 98 S420. It’s got a stuck piston. I’ve got a reman caliper waiting in the wings for it. Dan ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
Thanks! I hoping to put an end to the pneumatic issues that I have discovered that appear to have plagued this car for years. I spent a while studying all of the records last night, including the complete history from the MB dealership where it was purchased and maintained for the first ten years of its life. It’s had a grand total of four PSE pumps replaced over the years. Right now, the locks work, and the lumbar bladders would work (one is leaking due to age) but the back up aids don’t extend. Fuel mileage is marginal as well, so I’m almost positive there’s a vacuum leak in the system, too. If you’re not familiar with the PSE pump in the 90s models, it provides both vacuum and pressure for door locks, AC flaps, lumbar bladders and in the case of the W140 from 92-95, these little “antennae” or “sticks” that extend out of the tops of the rear fenders when the car is in reverse so you know where the corners of the car are. Mercedes refers to them as “back up aids.” The PSE works with engine vacuum in the sense that if engine vacuum to the system drops below a certain point the PSE will kick in to help out. This allows AC flaps to work when the engine is not running, primarily for the ACC’s “REST” function (heat available after the car is shut off.) There is a vacuum distribution block in the passenger front footwell that is prone to leak and often overlooked. I have a new one on order, as they’re cheap, but I’ll be testing this one today as I suspect that’s where the problem lies. The giveaway is the loss of AC flaps when engine vacuum drops due to acceleration. The PSE pump isn’t able to keep up and the vacuum drops, causing the flaps to go to the default (defrost) position. It’s pretty amazing looking back over the records on this car. I’m thinking the independent they used for the last ten years had a big boat, or a kid they needed to put through college. In less than 80,000 miles, the car has had the following replaced: Starter Alternator Power steering pump (2x) AC compressor (2x) AC evaporator (2x) AC condensor (2x) Ignition lock cylinder (2x) PSE pump (4x) It was like clockwork when they would have the car in for service with the independent and it would need some sort of major work. Dan > On Sep 5, 2015, at 10:50 AM, Craig via Mercedes wrote: > > > I wish you success! > > > Craig > > ___ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
Re: [MBZ] Replacing W140 Motor Mounts
On Sat, 05 Sep 2015 10:40:37 -0400 Dan Penoff via Mercedes wrote: > Just finished this job, second time I’ve done it, first time was on the > S500 coupe, this time on the 1994 S420. > > I bought the special offset wrench for removing the top mount bolt, as > it’s buried under the manifolds. Best $15 I ever spent for a special > tool for this job. It made it go much faster. I did the passenger > (easy) side in about 20 minutes, the driver’s side (difficult) in about > 40. > > Now I’m heading back out to put the transmission mount in. Pretty easy > job on the W140. I’m getting the nasty stuff out of the way early > today, then it’s time to spend sorting out the pneumatics. Tomorrow it > will be R&R of the right front caliper on the oldest boy’s 98 S420. > It’s got a stuck piston. I’ve got a reman caliper waiting in the wings > for it. I wish you success! Craig ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
[MBZ] Replacing W140 Motor Mounts
Just finished this job, second time I’ve done it, first time was on the S500 coupe, this time on the 1994 S420. I bought the special offset wrench for removing the top mount bolt, as it’s buried under the manifolds. Best $15 I ever spent for a special tool for this job. It made it go much faster. I did the passenger (easy) side in about 20 minutes, the driver’s side (difficult) in about 40. Now I’m heading back out to put the transmission mount in. Pretty easy job on the W140. I’m getting the nasty stuff out of the way early today, then it’s time to spend sorting out the pneumatics. Tomorrow it will be R&R of the right front caliper on the oldest boy’s 98 S420. It’s got a stuck piston. I’ve got a reman caliper waiting in the wings for it. Dan ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
[MBZ] Replacing W140 Motor Mounts
Just finished this job, second time I’ve done it, first time was on the S500 coupe, this time on the 1994 S420. I bought the special offset wrench for removing the top mount bolt, as it’s buried under the manifolds. Best $15 I ever spent for a special tool for this job. It made it go much faster. I did the passenger (easy) side in about 20 minutes, the driver’s side (difficult) in about 40. Now I’m heading back out to put the transmission mount in. Pretty easy job on the W140. I’m getting the nasty stuff out of the way early today, then it’s time to spend sorting out the pneumatics. Tomorrow it will be R&R of the right front caliper on the oldest boy’s 98 S420. It’s got a stuck piston. I’ve got a reman caliper waiting in the wings for it. Dan ___ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com