Hi Denis, this error indicates some kind of data corruption when talking
with the modem, usually due to some kind of electrical problem (bad cable,
interference etc).
Anyone knows how to solve this problem ?
Try plugging it into a different USB port, and also make sure that the cable
is far
Hi Ed,
pop up every 10 minutes. What is strange is that this behavior does not
happen under WindowsXP. Distributions like OpenSuSE however suffer from
this problem. Ubuntu 9.04 is even worse. Under Unbuntu, the modem is more
busy with synchronizing than with serving my connection.
perhaps
Hi Giampaolo,
Duncan, what about adding speed, signal strength, agreed ADSL standard and
bins composition to the driver's procfs file?
Unfortunately I don't know how to get anything except the speed. The
speed is already reported to the ATM layer.
Ciao,
Duncan.
Liste de diffusion modem
Hi Giampaolo,
I see. Lacking firmware documentation seems a common problem with these
devices, isn't it?
for these devices everything has been reverse engineered.
Ciao,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire :
Hi Ed,
A search through the WindowsXP directory brought to light that the very
old file alcaudsl.sys is still there. Not a suprise as I used the
installation disk from 06-06-2002 to load the speedtouch driver under
WindowsXP after I had installed WindowsXP. So I suppose it is the one used
The parameters for following provider are missing in your table in
FAQ, so after investigation I am posting them.
Thanks!
Best wishes,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se d�sinscrire : mailto:speedtouch-requ...@ml.free.fr?subject=unsubscribe
Hi,
While prepearing the firmware for speedtch module with dd there is a
chunk at the begining of KQD6_3.012 and ZZZL_3.012 that remains:
dd bs=1 count=991 skip=36 if=./KQD6_3.012 of=./speedtouch-1.bin
dd bs=1 count=935 skip=32 if=./ZZZL_3.012 of=./speedtouch-1.bin
What are that chunks
Hi,
modem_run.c:475:3: error: invalid preprocessing directive
#fork_interrupt_daemon
you commented it out wrong. Try turning it into this:
/*fork_interrupt_daemon(fdusb); */
Best wishes,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se d\xE9sinscrire :
Hi,
Basically I have to kill syslogd for modem_run to work sanely, the
reason for this seems to be modem_run spamming the message:
Error reading interrupts
if syslogd is running modem_run and syslogd fight for cpu and syslogd
spams me with Last message repeated n times (where n can get
Hi,
I have been using speedtouch-330's for a few years now with LFS-based
machines. I recently upgraded to kernel 2.6.25.8 and Linux-atm-2.5.1) and
all works fine with a system with a hard-disk. When I switch to a mirror
system running from a CDROM, the modem is recognised but the
Hi, the fact you see a web-page supplied by your ISP shows
that the modem is working: network packets are getting from
your ISP to you. I don't know why your ISP thinks things
are not configured right (you can always ask them to tell
you what's wrong), but my guess is that you authenticated
Hi, I haven't used ppp myself in years so this might
be wrong but...
I suppose my email adress is:
[EMAIL PROTECTED]
My mail passwd is:
DD
My connection identifier is:
fti/Tagada
user 'fti/Tagada'
My connection passwd is:
AbCdEf
Could you tell me the EXACT strings, even for () or
Should quotation marks, double and single, be omitted from script
entered in text editor?
In the section Make a Bootscript, should the letters fi actually be if?
Any assistance would be appreciated as this is my first attempt @ Linux
and I have been trying to get online for 5 days.
sudo in -s ../init.d/dial /etc/rc2.d/S95dial
sudo in -sf ppp/resolv.conf /etc/resolv.conf
System will not accept 'in' on either line,
System will not accept '../init.d/dial' no such directory.
It's 'ln' not 'in'.
Ciao,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se
Salut,
debug
kdebug 1
noipdefault
defaultroute
pty /usr/sbin/pppoa3 -m 1 -c -vpi 8 -vci 35
sync
user [EMAIL PROTECTED]
noauth
noaccomp
nopcomp
noccp
novj
holdoff 4
persist
maxfail 25
usepeerdns
debug
cela vient d'ou ce fichier de configuration?! A mon avis, c'est
Comment fait-on pour signaler que la solution a été trouvée.
Est-ce que tu veux dire: comment savoir si ca marche? Parce
que tu auras une connexion internet pardi!
Ciao,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
je fais /usr/sbin/pppd call adsl
essaie
/usr/sbin/pppd call adsl debug
et envoie-moi les informations imprimees. Il se peut
que les informations ne s'affichent pas, dans ce cas
elles sont enregistrees dans tes logs systemes, du genre
/var/log/messages.
Ciao,
Duncan.
Liste de
Salut,
Feb 1 17:42:27 localhost pppd[2926]: pppd 2.4.4 started by root, uid 0
Feb 1 17:42:27 localhost pppd[2926]: Couldn't get channel number:
Input/output error
Feb 1 17:42:31 localhost pppd[2926]: Using interface ppp0
Feb 1 17:42:31 localhost pppd[2926]: Connect: ppp0 -- /dev/pts/1
Bonjour j'ai tout fait comme dans le tutorial, j'ai réusssi à reconfigurer le
noyau, j'ai remis speedtech.ko à sa place mais toujours rien.
tu as les resultats de cat /proc/net/atm/speedtch et dmesg qui suivent ce
mail. Je ne sais plus à kel saint me vouer.
Salut,
speedtch 1-2:1.0: found
je ne sais pas comment récupérer le contenu du fichier speedtouch. Je
t'envoie les deux autres. Toutefois j'ai constaté avec une grande surprise
que, voulant rechercher l'aide sur speedtouch, j'ai entré speedtouch --help,
le modem a démarré correctement. Je t'envoie tout de même ces
how can I configure the kernel with the ATM
Sur la page
http://linux-usb.sourceforge.net/SpeedTouch/LFS/index.html
il y a la liste d'options qu'il faut pour ton noyau. Mais verifie
d'abord qu'il n'y a pas simplement un probleme avec le chargement
automatique des modules: si tu fais
It looks like the module failed to load because the kernel is not
configured with ATM support.
usbatm: Unknown symbol atm_dev_deregister
usbatm: Unknown symbol atm_dev_register
usbatm: Unknown symbol vcc_release_async
usbatm: Unknown symbol atm_charge
Ciao,
Duncan.
Liste de diffusion
Rien ne se passe et je n'ai toujours rien kan je fait cat
/proc/net/atm/speed. Cela doit être certainement parce que j'ai supprimé le
speedtch.ko
En effet, suprimer le speedtch.ko est fatal.
Ciao,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL
Bonjour,
j'ai mis à jour mon noyau et je ne peux plus avoir la connection sur le
nouveau noyau (2.6.2.3).
c'est vraiment 2.6.2.3, et pas 2.6.23? Puisque 2.6.2 est tres tres ancien...
Je parviens à me connecter sur l'ancien noyau et pas sur le nouveau.
Lorsque je lance speedtouch-start, il
Hi, Peru values are :
.pe, Peru Speedy [Telefonica Terra] PPPoA 8 60
Thanks for the info!
Best wishes,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
Hi,
I have serious problem with my SpeedTouch 330 modem. Lately i have changed
motherboard in my home router. Since then i get random disconnections.
Sometimes my connection
last for 10 hours, somethimes 20,and it maybe 1 hour as well. After
disconnection i can't reconnect it until i reboot
The biggest problem is that only reboot of system helps for this situation.
I can't unload usbatm module, even after unloading speedtch and uhci_hcd
first.
That is not normal. What does lsmod say? What kernel version do you have?
Killing all pppd doesn't help either. Module is busy, and
Whilst switching between desktops, I did notice the message come up on
booting stating The Speedtouch Firmware did not load. This seems to be
a
vital clue; does anyone have any suggestions ?
If the firmware doesn't load, no connection can be made at all.
Yes, however Roger previously
The dmesg | less command reveals 100s of lines of info! However, an
initial visual scan reveals the following 2 lines:
[ 28.813332] speedtch 1-1:1.0: found stage 1 firmware speedtch-1.bin
[ 28.966755] speedtch 1-1:1.0: found stage 2 firmware speedtch-2.bin
I'm afraid I'm a bit
Hi Roger,
I am trying to get my Speedtouch modem working with the Feisty Fawn version
of Ubuntu. I got the thing working before (with help from here) on Dapper
Drake, but that was some time ago and I've lost the advice sent to me.
I have followed the web instructions, cutting and pasting
Hi Tomy, I think the problem is that the packets are going to the adummy
driver. Here you can see that interface 0 is adummy:
Itf TypeESI/MACaddr AAL(TX,err,RX,err,drop) ... [refcnt]
0 adummy 0 ( 0 0 0 0 0 ) 5 ( 3988 0 0 0 0 ) [4]
1
Hi Tomy,
AAL5: tx 0 ( 0 err ), rx 0 ( 0 err, 0 drop )
this shows that no packets reached the speedtch driver, let alone
the modem - not surprising that you're not seeing much connectivity!
Something fundamental is broken in the way you have things configured.
Perhaps you could paste *exactly*
/proc/net/atm/speedtch:1
Speed Touch USB (usb-:00:1d.0-2)
MAC: 00:90:d0:4e:49:16
AAL5: tx 0 ( 0 err ), rx 0 ( 0 err, 0 drop )
Line up
Was this after trying to ping the gateway? If not,
please try pinging the gateway, then send the contents
of this file again.
Thanks,
Duncan.
Liste
Hi Tommy,
I tested pinging my gate way. It does not ping at all. The response I get it:
#Ping 10.200.1.1
PING 10.200.1.1 (10.200.1.1) 56 (84) bytes of data
--- 10. 200.1.1 Ping statistics ---
125 packets trasmitted, 0 received, 100% packet loss time 124030ms
By the way, how do
Hi Tommy,
localhost tomy # atmarp -s 10.200.1.1 8.35 null
atmarp: Address already in use
this Address already in use is not good. Is this
the second time you did this?
D.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
I am attaching here the contents of /proc/net/atm
Unfortunately the list strips off attachments so I didn't
get them. Please include them inline.
Thanks,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
Hi Tommy,
For me VPI = 8, and VCI = 35 and netmask is 255.255.0.0. the IPs of the
nameservers are given in /etc/resolv.conf. What else do I need to do?
I'm not sure why you mention the IP of your nameservers - this is not the
same as the gateway IP. So... do you know your IP address and the
Hi Tommy,
For several days I have been trying to configure my speedtouch usb modem on
my gentoo box.
I tried the documentation for gentoo at
http://www.linux-usb.org/SpeedTouch/gentoo/index.html
But I have not been sucessful. I am connected to a LAN with a static ip
address, netmask
I downloaded the libatm1_2.4.1-17_i386.deb from ubuntu repositories,
logged back into this machine, installed the library, and restarted.
Voilá! It's working and working very well. And that's all I wanted!
OK, thanks for letting us know. I wish more people would post their
solutions - it
Hi, try adding debug to pppd. For example, if you normally do
pppd call speedtch
try
pppd call speedtch debug
This should output all kinds of info to your system logs (not
to the console). Please send the output here.
Thanks,
Duncan.
Liste de diffusion modem ALCATEL
Hi Fabrizio,
... But sometimes, in some situation, this is not sufficient: when the ADSL
goes down it can't be reconnet neither this script.
why does the ADSL line go down in the first place?
Perhaps the device must be re-inizialitating: for do this is necessary to
unload all modules
No, actually works fine.
Do you need these files while pppd was failing ?
Yes.
Ciao,
D.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
hello, i need to share a internet connection with mandriva 2007, i have
configured the modem by pppoe, but i don´t know how to share this
connection. i try with the tools that has mandriva, with no
results(recognize my lan card in nas0). and i don´t understand the
manual method.
I'm not
If I don't forget, I'll try to whip up something next Monday. Please
don't hesitate to remind me, since I've got a memory like a sieve!
Hi Karl, in recent kernels you can get the link rate from the file
/sys/class/atm/speedtch0/link_rate
That holds a default value until the line
On Monday 5 February 2007 19:30:04 Samuel Adams wrote:
So rmmod speedtch and modprobe speedtch dl_512_first=1 seemed to get
my modem dialed in, but programs such as firefox and evolution still
will not recognize the connection. Any ideas here?
Most likely a DNS problem. I've no time right
I found a log file called /var/log/syslog. Although it's quite lengthy, I
can see that the 2 drivers (speedtch-1 and speedtch-2) appear to be loading
correctly. However, further down the file, it says that no Speedtouch
device was found. It's a standard USB modem. No router is involved
Firstly, if modem_run is no longer needed, can I uninstall it?
Yes.
Secondly, the only lines I can see relating to pppd are these:-
pppd[5711]: /usr/lib/pppd/2.4.4/rp-pppoatm.so: cannot open shared object
file: No such file or directory
pppd[5711]: Couldn't load plugin rp-pppoatm.so
You seem to be right about the version though. I only have one PPPD
executable in /usr/sbin. It's dated 10th July 2006 which usually means it
came with Dapper. I asked on the Ubuntu forum to see if there's a newer
version but nobody responded.
apt-cache show ppp
This might be
Hi Karl,
Debian Etch, 2.6.18 stock kernel.
can you please try 2.6.19. Extra modem initialization
code was added, based on some reverse engineering by
David Woodhouse. That said, I can get 3-4 meg with
a manta-ray even without that, i.e. about 400kbytes/sec
which is what you reported you
Duncan, typing cat /proc/net/atm/speed* produced:-
cat: /proc/net/atm/speed*: No such file or directory
OK, that explains why pppd didn't work: the modem is
not plugged in. Or, if it is plugged in, then it has
not initialized, or has been logically disconnected.
and typing apt-cache
No problem. What would I need to do? Attach them to an email or something
else?
Just attach /var/log/syslog
Ciao,
D.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
Ok, that helped a bit. I am now getting a more consistent 3Meg, but this
is still only half what I can get on the ISP-supplied router. One thing
I'm noticing is that IRQ's are taking up a lot of CPU time (5-10%).
Could this have something to do with it? Or is 3Meg the most I am likely
to
Jan 29 11:59:29 localhost kernel: [4294695.534000] usb 1-2: reset full speed
USB device using uhci_hcd and address 3
Jan 29 11:59:29 localhost kernel: [4294695.659000] usbcore: registered new
driver speedtch
Jan 29 11:59:29 localhost kernel: [4294695.709000] speedtch 1-2:1.0: found
stage
Actually, now I come to think about it some more I suspect
I know what the problem is. Try doing this (as root):
rmmod speedtch
modprobe speedtch dl_512_first=1
Unplug the modem and plug it back in again. Does it
work? What do you get in your system log?
Ciao,
Duncan.
On Wednesday 31 January 2007 06:51:58 Duncan Sands wrote:
Actually, now I come to think about it some more I suspect
I know what the problem is. Try doing this (as root):
rmmod speedtch
modprobe speedtch dl_512_first=1
Unplug the modem and plug it back in again. Does
Here's the output you requested of :cat /proc/net/atm/devices
Itf Type ESI/Macaddr AAL(TX,err,RX,err,drop) ... [refcnt]
Hope that sheds some light - because I have no idea what it means.
It means that the modem failed to initialize properly, or initialized
ok but the
Hi! Sorry if this has been asked before, but an archive search on error 253
produced no results. Any ideas regarding this modem_run error 253 with
openSuSE 10.2? Thank you!
First of all, you don't need any of this because you have a kernel driver
that's taking care of (almost) everything:
Hi Chris,
The distribution of Linux I am running is IPCop, which is a
dedicated firewall system. This is currently running kernel
2.4.31 and as it comes as a dedicated firewall the kernel is
compiled with specific functions. Using a latter kernel is not an
option.
On Tuesday 23 January 2007 17:31, Samuel Adams wrote:
Duncan,
Here's the output of pppd call speedtch debug...
from the terminal:
Plugin pppoatm.so loaded.
Connect (8,35): No such device.
and from the syslog:
localhost pppd[5204]: Plugin pppoatm.so loaded.
localhost pppd[5204]:
sometimes there is an entry for pppd, sometimes not. If there is, it says
authentication failed. (even though I used the noauth command in my
speedtch script) Additionally ntp reports that ntp.ubuntu.org cannot be
found. Also DHCP persistently is trying to do something with eth0 - why, I
PS: debug output from pppd call speedtch debug will most
likely appear in your system logs, not in the terminal.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
On Sunday 21 January 2007 12:14, Clive Messer wrote:
On Friday 19 January 2007 16:49, Duncan Sands wrote:
PS: You may also need the attached firmware.
-- Binary/unsupported file stripped by Listar --
-- Type: application/octet-stream
-- File: speedtch-1.bin.4
-- Binary
Why should a Thompson SpeedTouch 330 running under Windows 2000
synchronise with the line at a consistently higher rate, than the
same modem, on the same hardware, using the same line, under
IPCop using the Linux firmware/driver ZZZL_3.012(Both kernel and
user mode drivers).
Try
Is br2684 module (or maybe include in kernel but I have not tested)
selected
in your kernel .config?
Yes, i am using br2684 that i downloaded from http://gothicx.blogs.sapo.pt
Gilles was asking about the kernel module, which is something else. What
is the output of running this command:
Second I am trying to do this manually now but the instructions on this
web
page:
http://www.linux-usb.org/SpeedTouch/mandrake/index-es.html
Asks me to make a file called firmware-extractor.txt executable, how can I
make it executable?
chmod 755 firmware-extractor
it should
Yes, once MODULE_UNLOAD is set MODULE_FORCE_UNLOAD is on via the
default configuration options in 2.6.19.1. That said, looking back through
my cvs it seems that I on earlier versions I had explicitly set it (although
why I don't know).
Should I try unsetting it?
Please do. I'm not saying
Well, here are the results...
Dec 31 16:21:31 pfw kernel: ATM dev 0: usbatm_extract_one_cell: unknown
vpi/vci (0/3656)!
Dec 31 16:44:42 pfw kernel: ATM dev 0: usbatm_extract_one_cell: unknown
vpi/vci (92/7393)!
Dec 31 18:57:27 pfw kernel: ATM dev 0: usbatm_extract_one_cell: unknown
Hi Steve,
There's an experimental feature which only works with speedtouch 330s or
better: download using isochronous urbs, rather than bulk urbs. This
should improve performance on high speed connections. You can turn it
on with enable_isoc=1. It may be worth turning on, because one
On Tue, Jan 02, 2007 at 11:45:24AM +0100, Duncan Sands wrote:
e) various other cases
This is us. I hope to look into this further tonight.
Well, the only potentially relevant test I could find
in the uhci hcd is that it returns -EINVAL if the USB
device is low speed
e) various other cases
This is us. I hope to look into this further tonight.
Ciao,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
NET: Unregistered protocol family 20
speedtch: Unknown symbol usbatm_usb_disconnect
speedtch: Unknown symbol usbatm_usb_probe
I don't know what these unknown symbols are about.
Neither do I
Just a thought: do you have CONFIG_MODULE_FORCE_UNLOAD
set in your kernel's .config?
usb 1-2: usbdev_ioctl: SUBMITURB
usb 1-2: bulk urb
usb 1-2: submit urb
usb 1-2: direction=IN
usb 1-2: userurb=bf82efec
usb 1-2: transfer_buffer_length=6
usb 1-2: actual_length=0
usb 1-2: data: c0 01 0f 00 00 00
usb 1-2: usbfs: usb_submit_urb returned -22
It looks to me like -EINVAL
So can you please
do the following: make sure that usbcore is loaded with usbfs_snoop=1
(usbfs_snoop is a module parameter). You can do this by (as root)
removing usbcore then reloading it:
rmmod usbcore
modprobe usbcore usbfs_snoop=1
In new kernel I compiled usbcore into
Lots changed in the kernel and the USB layer. Nothing changed in
the speedtouch driver between 2.6.17 and 2.6.18. There were some
changes for 2.6.19.
Yes, I noticed. My question was really to do with the USB stuff, mainly
because this all started when I experienced massive packet loss
I notice that whenever it fails you have this message
ifup: No configuration found for ppp0
Dec 22 01:41:48 linux pppd[5772]: sent [LCP ConfReq id=0x1 asyncmap 0x0
magic 0x278274c1]
Dec 22 01:41:49 linux ifup: No configuration found for ppp0
Dec 22 01:41:51 linux pppd[5772]: sent [LCP
Hi,
I have the following:
Speedtouch 330 silver,
2 hard drives, one with FC6 adn one with FC5 and Windows. I have just
isntalled the FC6.
the speedtouch instructions work well but:
If I boot from the FC5 and Winfdows drive all is well
If I boot from the FC6 drive with teh FC5
sorry ot be a pain but where exactly woudl i find this? what filenme
shoidl i search for??
Dunno. What instructions did you follow to install the modem?
Ciao,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se dىsinscrire : mailto:[EMAIL PROTECTED]
Will be nice the webmaster of the page known about
this and correct the error if this exists.
Unfortunately our webmaster, who did a wonderful job,
can't work on it anymore. Any volunteers to take it
over?
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire :
On Monday 6 November 2006 20:50, Ilaria Zanellato wrote:
Hi,
I've just moved to linux, installing Fedora core 6. I followed the
instructions at http://www.linux-usb.org/SpeedTouch/fedora/index.html using
the steps appropriate for PPPoA. I have a revision 4 modem.
When
I boot my PC, the
As suggested in the analysis cited above, this fault means that
downloading a file over HTTP consisting of all ones (i.e. 0xff * lots)
reproduces the fault reliably. I've tested this on the newer kernel
and it now downloads correctly.
Great!
Glad it worked out,
Duncan.
Liste de diffusion
I've got a Speedtouch 4.00 connected to my old Linux box as an ADSL
router. After a few problems getting the firmware images, it all
worked fine.
The problem I have now, is that it intermittently stops working,
silently, with no error messages.
Let me guess: kernel 2.6.17 ?
Ciao,
there have been reports that speedtouch is broken in 2.6.17 kernels:
http://lists.infradead.org/pipermail/usbatm/2006-August/000863.html
http://www.mail-archive.com/speedtouch%40ml.free.fr/msg08172.html
Before I try myself with the Debian etch kernel (2.6.17.12), can anybody
tell,
if
On Saturday 30 September 2006 23:43, Andrew Benton wrote:
Hello world,
Is there a way to get the kernel to say what revision of Speedtouch is
attached it? Perhaps by reading a file in /proc or /sys? It used to have
details in /proc/bus/usb/devices but that file doesn't seem to be there
On Wednesday 12 July 2006 12:07, Clive Messer wrote:
Duncan,
Are you aware of the issue on Fedora 45 with a 2.6.17 kernel?
https://www.redhat.com/archives/fedora-list/2006-June/msg03963.html
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=196560
Yes I am, see
On Wednesday 12 July 2006 12:34, Andy Duplain wrote:
Duncan, I have been having problems with connections dying under 2.6.17,
which disappear when I revert to 2.6.16.20. I saw a message on linux.kernel
that you have received a couple of reports like this. You seem to think it's
not
Jun 28 19:30:39 x- pppd[2182]: LCP: timeout sending Config-Requests
Jun 28 19:30:39 x- pppd[2182]: Connection terminated.
Jun 28 19:30:39 x- pppd[2182]: Modem hangup
Jun 28 19:30:39 x- pppd[2182]: Exit.
Most likely wrong vpi.vci
What are you using?
D.
Liste
Yes, I saw the thread but I don't understood :-). I think it's very
technical... maybe someone
has a pragmatic and easier way to do it.
From http://www.mail-archive.com/speedtouch%40ml.free.fr/msg07980.html:
Basically to start a routed IP connection, you need those data:
- LOCAL_IP (your
The extra messages may be in your system logs. Have a look in
/var/log/messages or /var/log/syslog to see if any turned up.
Ciao,
D.
oh i see...
this is what i get then..
Hmmm, that's not it either. Are you really really sure you ran
pppd with the debug option?
Ciao,
Duncan.
running pppd with the debug option doesn't produce more messages.. the
output is excactly the same..
The extra messages may be in your system logs. Have a look in
/var/log/messages or /var/log/syslog to see if any turned up.
Ciao,
D.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se
Try running pppd with the debug option. For example,
if before you ran it using
pppd call speedtouch
now run it using
pppd call speedtouch debug
This will produce more details about what pppd is doing.
Ciao,
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se
Does this mean speedtch isn't written with suspend in mind?
It does, mainly because I've never suspended a computer
in my life! Please feel free to add suspend support; I'll
also add it to my list of things to do.
Ciao,
D.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire
Hi Vouno,
thanks for your answer.
I'd like to have some more details.
The only way i found to reestabilish the connection is the reboot of the
computer.
Hi Vouno, try applying the following patch to pppd's pppoatm.c:
I think this is a patch to apply to recompile the kernel so to
At this point if i launch ppp call adsl updetach the connection cannot be
completed with this error:
#Plugin pppoatm.so loaded.
#connect(8.35): Address already in use
The ppp0 interface is still active. It didn't recognize the modem
disconnection.
So, now i kill the pppd daemon.
Duncan: replies to your questions.
Did you do this at a time when pppd was failing
to connect?
Thanks,
D.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
1 Logged in as myself, switched to root then issued pppd call speedtch.
Output appended below.
Click on Firefox and page opens and allows me to visit other websites.
ping 68.142.226.54 produces the line '64 bytes from 68.142.226.54 icmp_seq=31
ttl=57 time = xxx'.
The value of xxx
2 If I try to open Firefox I get the message 'www.novell.com could not be
found'.
3 ping 68.142.226.54 generates the message 'network is unreachable'.
If you do
pppd call speedtch
as the super-user (root), and then try again 2 and 3 above, do things work
better?
If so, that would
pppoa is easier because you don't need br2684ctl to create the nas0
interface. Go with pppoa
He may not have the choice. He needs to ask his ISP whether it
uses PPPoA (ppp over ATM) or PPPoE (ppp over ethernet) or something
else.
Duncan.
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour
local IP address 84.69.1.48
remote IP address 62.25.198.171
primary DNS address 195.92.195.95
secondary DNS address 195.92.195.94
You are online! What happens if you do:
ping 68.142.226.54
?
Modem lights still blinking continuously red on boot.
And after booting?
Ciao,
Just out of curiosity, the file to configure etc/ppp/peers/speedtch had 6
commented lines to disable compression.
Would uncommenting them have changed anything?
It would have suppressed this
sent [CCP ConfReq id=0x1 deflate 15 deflate(old#) 15 bsd v1 15]
sent [IPCP ConfReq id=0x1
1 Output from command /sbin/lspci grep USB:
You forgot the pipe (|), should be:
/sbin/lspci | grep USB
2 Output from command lsmod:
br2684 8452 0
bridging module for PPP over ethernet
pppoatm 5760 0
needed for PPP over ATM
ppp_generic 28052 1 pppoatm
PPP support
slhc 7296 1
1 - 100 of 615 matches
Mail list logo
