Just put it in the pub directory, not a subdirectry. Consider using something like gzip to make the files smaller, too.
On Mon, Mar 1, 2010 at 2:40 AM, hcadrexler <[email protected]>wrote: > Hi Brian, > > I just tried to upload a few .raw files and the fasta db into the pub > folder using filezilla, however, filezilla tells me that I that there > is no adequate directory for the upload (see error message)?? > > .............. > Command: STOR /pub/Hannes_20100301/20091125_AD_Boiani_oocyte_03.raw > Response: 550 /pub/Hannes_20100301/ipi.MOUSE.v3.64.fasta: No such > file > or directory > Command: PASV > Response: 550 /pub/Hannes_20100301/20091125_AD_Boiani_oocyte_03.raw: > No such file or directory > Error: Critical file transfer error > ............. > > Kind regards, > > Hannes > > On 26 Feb., 19:18, Brian Pratt <[email protected]> wrote: > > Strange indeed. If you can send me a minimum data set that shows the > > problem I could take a look (presumably three files and the fasta db). > If > > they're too big to email, you can ftp toftp://insilicos.serveftp.net/pub > . > > Brian > > On Fri, Feb 26, 2010 at 7:10 AM, Hannes Drexler > > <[email protected]>wrote: > > > > > Hi Brian, > > > > > thought about it too, however, when I delete the first two > > > successfully handled files from the sequence and start the database > > > search again with the next / third file of the list, the subsequent > > > two files are also successfully sent through the pipeline. I repeated > > > it a few more times now and to me it looks like as if XTandem database > > > searches are currently only possible in tranches of two. Strange, > > > isn´it? > > > > > Hannes > > > > > 2010/2/24 Brian Pratt <[email protected]>: > > > > You'll want to narrow it down to identify the problem - for example, > > > what > > > > happens when you omit that 3rd file? > > > > > > On Wed, Feb 24, 2010 at 2:04 AM, hcadrexler < > [email protected]> > > > > wrote: > > > > > >> Hi there, > > > > > >> I tried to perform an XTandem search following the XTandem 2009 > > > >> tutorial using my own data (29 mzXML files). The Database search is > > > >> performed for the first two files in the sequence without any > problems > > > >> but then stops and does not proceed any further with the third (and > > > >> subsequent) files. I cannot figure out where the mistake was made. > > > >> Does anybody know why this might happen? > > > > > >> Kind regards, > > > > > >> Hannes > > > > > >> -- > > > >> You received this message because you are subscribed to the Google > > > Groups > > > >> "spctools-discuss" group. > > > >> To post to this group, send email to > [email protected]. > > > >> To unsubscribe from this group, send email to > > > >> [email protected]<spctools-discuss%[email protected]> > <spctools-discuss%[email protected]<spctools-discuss%[email protected]> > > > > > . > > > >> For more options, visit this group at > > > >>http://groups.google.com/group/spctools-discuss?hl=en. > > > > > > -- > > > > You received this message because you are subscribed to the Google > Groups > > > > "spctools-discuss" group. > > > > To post to this group, send email to > [email protected]. > > > > To unsubscribe from this group, send email to > > > > [email protected]<spctools-discuss%[email protected]> > <spctools-discuss%[email protected]<spctools-discuss%[email protected]> > > > > > . > > > > For more options, visit this group at > > > >http://groups.google.com/group/spctools-discuss?hl=en. > > > > > -- > > > You received this message because you are subscribed to the Google > Groups > > > "spctools-discuss" group. > > > To post to this group, send email to [email protected] > . > > > To unsubscribe from this group, send email to > > > [email protected]<spctools-discuss%[email protected]> > <spctools-discuss%[email protected]<spctools-discuss%[email protected]> > > > > > . > > > For more options, visit this group at > > >http://groups.google.com/group/spctools-discuss?hl=en. > > -- > You received this message because you are subscribed to the Google Groups > "spctools-discuss" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]<spctools-discuss%[email protected]> > . > For more options, visit this group at > http://groups.google.com/group/spctools-discuss?hl=en. > > -- You received this message because you are subscribed to the Google Groups "spctools-discuss" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/spctools-discuss?hl=en.
