Hi! This is where the original post of Zsolt comes in. You should start the PC with the MIB520 connected and the IRIS removed, and while it is running then connect the IRIS mote to the mib520, that worked for him and we have no idea what is going on. Why a simple reset would not result in the same behaviour.
Miklos On Mon, Aug 30, 2010 at 2:52 PM, nithin k n <[email protected]> wrote: > HI , I did install the new version of tinyos, and everything worked except a > problem while starting the base station driver , i burnt a mote with UDPEcho > and other with IPBaseStation . the problem is in starting the driver. > > check out the screenshot attached which says the problem. > > Regards, > Nithin keen > > On Mon, Aug 30, 2010 at 1:14 PM, Miklos Maroti <[email protected]> > wrote: >> >> Hi! >> >> Use the latest SVN vesrion of tinyos, not the one you have installed >> from tar/rpm. >> >> Miklos >> >> On Mon, Aug 30, 2010 at 6:30 AM, nithin k n <[email protected]> >> wrote: >> > attached screenshots supports the problem statement what i reffered >> > to... >> > >> > ---------- Forwarded message ---------- >> > From: nithin k n <[email protected]> >> > Date: Mon, Aug 30, 2010 at 9:53 AM >> > Subject: Re: [Tinyos-help] Blip on IRIS reset problem >> > To: [email protected], [email protected], >> > [email protected], Miklos Maroti <[email protected]> >> > >> > >> > HI ALL ... >> > HI Zsolt , in my case the official IPBaseStation is itself not >> > gettin >> > installed. >> > when i give "make iris install mib520,/dev/ttyUSB0" the errors appear >> > related to cc2420 interfaces and wirings associated with BaseStationP.nc >> > , >> > like in CC2420Config and CC2420ControlC. >> > >> > can u suggest me what should i do? i thought like i should go for making >> > changes in BaseStationp.nc code , (i.e., changing cc2420's interfaces >> > and >> > wirings to rf230's interfaces and wirings) BECAUSE, IRIS XM2110 DOESN'T >> > HAS >> > CC2420, RATHER IT IS WITH RF230 RADIO. >> > If you think its some other way to the solution, then please send me >> > the >> > IPBaseStation code (/opt/tinyos-2.x/apps/IPBaseStation) , atleast I'll >> > check >> > it. >> > >> > Regards, >> > Nithin keen >> > On Sun, Aug 29, 2010 at 2:04 AM, Miklos Maroti >> > <[email protected]> >> > wrote: >> >> >> >> miklos >> >> >> >> >> >> ---------- Forwarded message ---------- >> >> From: Zsolt Szabó <[email protected]> >> >> Date: 2010/8/6 >> >> Subject: [Tinyos-help] Blip on IRIS reset problem >> >> To: [email protected] >> >> >> >> >> >> Hi all. >> >> >> >> I managed to get the Iris mote to work with the IPBaseStation and blip >> >> driver, but quite a tricky way. I am using a mib520CA programmer for >> >> communication interface. When i plug the programmer in and attach the >> >> mote onto it the led2 will light. But when starting the driver on pc >> >> the led light goes off, or even before all flashes up then go off. >> >> After this using the programmer's reset switch does not seem to help, >> >> just detacthing and reattaching the mote. In this case the led2 turns >> >> on as default. I even tried doing this with disabling all the leds and >> >> just enable one specific led in the Boot.booted event. I always got >> >> the same result. After strarting blip driver, the mote halts, that >> >> means it does not reboot itself, and i can't do that either manually >> >> using reset switch. Now the tricky part. If i don't attach the mote to >> >> the programmer but start the blip driver on pc that tries to iniciate >> >> communication i wait for 1 or sec while the driver tries to initiate >> >> communication with the mote. Then i attach the mote and the blip is >> >> functioning properly. I can even login via telnet onto the mote and if >> >> i want to i can even reset the device using the programmer's reset >> >> switch. >> >> What can be so spoiled in the IPBaseStation that the mote does not >> >> accept even the hardware reset if the first (standard) case? >> >> The phenomenon can be reproduced using unmodified, official tinyos app >> >> IPBaseStation and blip driver. >> >> Have someone experiancing this reset problem? Does anybody have >> >> suggestions for solving this issue? >> >> >> >> Regards >> >> Zsolt >> >> >> >> _______________________________________________ >> >> Tinyos-help mailing list >> >> [email protected] >> >> >> >> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >> > >> > >> > > > _______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
