i got the problem solved by the trick of Zsolt , Thanks for all the support.
Cheer, Nithin keen On Mon, Aug 30, 2010 at 6:49 PM, nithin k n <[email protected]> wrote: > hi ! did the same trick of starting the driver(for IPBaseStation in iris) > works everytime for you or that worked only the 1st time >? .. > > Regards > Nithin keen > > ---------- Forwarded message ---------- > From: nithin k n <[email protected]> > Date: Mon, Aug 30, 2010 at 6:47 PM > Subject: Re: [Tinyos-help] Blip on IRIS reset problem > To: Miklos Maroti <[email protected]> > > > IS THE SAME TRICK STILL WORKING FOR HIM ? OR THAT WORKED ONLY ONCE IN THE > FIRST TIME > ? > > REGARDS > NITHIN KEEN > > > On Mon, Aug 30, 2010 at 6:25 PM, Miklos Maroti > <[email protected]>wrote: > >> Hi! >> >> This is where the original post of Zsolt comes in. You should start >> the PC with the MIB520 connected and the IRIS removed, and while it is >> running then connect the IRIS mote to the mib520, that worked for him >> and we have no idea what is going on. Why a simple reset would not >> result in the same behaviour. >> >> Miklos >> >> On Mon, Aug 30, 2010 at 2:52 PM, nithin k n <[email protected]> >> wrote: >> > HI , I did install the new version of tinyos, and everything worked >> except a >> > problem while starting the base station driver , i burnt a mote with >> UDPEcho >> > and other with IPBaseStation . the problem is in starting the driver. >> > >> > check out the screenshot attached which says the problem. >> > >> > Regards, >> > Nithin keen >> > >> > On Mon, Aug 30, 2010 at 1:14 PM, Miklos Maroti < >> [email protected]> >> > wrote: >> >> >> >> Hi! >> >> >> >> Use the latest SVN vesrion of tinyos, not the one you have installed >> >> from tar/rpm. >> >> >> >> Miklos >> >> >> >> On Mon, Aug 30, 2010 at 6:30 AM, nithin k n <[email protected]> >> >> wrote: >> >> > attached screenshots supports the problem statement what i reffered >> >> > to... >> >> > >> >> > ---------- Forwarded message ---------- >> >> > From: nithin k n <[email protected]> >> >> > Date: Mon, Aug 30, 2010 at 9:53 AM >> >> > Subject: Re: [Tinyos-help] Blip on IRIS reset problem >> >> > To: [email protected], >> [email protected], >> >> > [email protected], Miklos Maroti < >> [email protected]> >> >> > >> >> > >> >> > HI ALL ... >> >> > HI Zsolt , in my case the official IPBaseStation is itself not >> >> > gettin >> >> > installed. >> >> > when i give "make iris install mib520,/dev/ttyUSB0" the errors appear >> >> > related to cc2420 interfaces and wirings associated with >> BaseStationP.nc >> >> > , >> >> > like in CC2420Config and CC2420ControlC. >> >> > >> >> > can u suggest me what should i do? i thought like i should go for >> making >> >> > changes in BaseStationp.nc code , (i.e., changing cc2420's interfaces >> >> > and >> >> > wirings to rf230's interfaces and wirings) BECAUSE, IRIS XM2110 >> DOESN'T >> >> > HAS >> >> > CC2420, RATHER IT IS WITH RF230 RADIO. >> >> > If you think its some other way to the solution, then please send me >> >> > the >> >> > IPBaseStation code (/opt/tinyos-2.x/apps/IPBaseStation) , atleast >> I'll >> >> > check >> >> > it. >> >> > >> >> > Regards, >> >> > Nithin keen >> >> > On Sun, Aug 29, 2010 at 2:04 AM, Miklos Maroti >> >> > <[email protected]> >> >> > wrote: >> >> >> >> >> >> miklos >> >> >> >> >> >> >> >> >> ---------- Forwarded message ---------- >> >> >> From: Zsolt Szabó <[email protected]> >> >> >> Date: 2010/8/6 >> >> >> Subject: [Tinyos-help] Blip on IRIS reset problem >> >> >> To: [email protected] >> >> >> >> >> >> >> >> >> Hi all. >> >> >> >> >> >> I managed to get the Iris mote to work with the IPBaseStation and >> blip >> >> >> driver, but quite a tricky way. I am using a mib520CA programmer for >> >> >> communication interface. When i plug the programmer in and attach >> the >> >> >> mote onto it the led2 will light. But when starting the driver on pc >> >> >> the led light goes off, or even before all flashes up then go off. >> >> >> After this using the programmer's reset switch does not seem to >> help, >> >> >> just detacthing and reattaching the mote. In this case the led2 >> turns >> >> >> on as default. I even tried doing this with disabling all the leds >> and >> >> >> just enable one specific led in the Boot.booted event. I always got >> >> >> the same result. After strarting blip driver, the mote halts, that >> >> >> means it does not reboot itself, and i can't do that either manually >> >> >> using reset switch. Now the tricky part. If i don't attach the mote >> to >> >> >> the programmer but start the blip driver on pc that tries to >> iniciate >> >> >> communication i wait for 1 or sec while the driver tries to initiate >> >> >> communication with the mote. Then i attach the mote and the blip is >> >> >> functioning properly. I can even login via telnet onto the mote and >> if >> >> >> i want to i can even reset the device using the programmer's reset >> >> >> switch. >> >> >> What can be so spoiled in the IPBaseStation that the mote does not >> >> >> accept even the hardware reset if the first (standard) case? >> >> >> The phenomenon can be reproduced using unmodified, official tinyos >> app >> >> >> IPBaseStation and blip driver. >> >> >> Have someone experiancing this reset problem? Does anybody have >> >> >> suggestions for solving this issue? >> >> >> >> >> >> Regards >> >> >> Zsolt >> >> >> >> >> >> _______________________________________________ >> >> >> Tinyos-help mailing list >> >> >> [email protected] >> >> >> >> >> >> >> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >> >> > >> >> > >> >> > >> > >> > >> > > >
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
