hi ! did the same trick of starting the driver(for IPBaseStation in iris) works everytime for you or that worked only the 1st time >? ..
Regards Nithin keen ---------- Forwarded message ---------- From: nithin k n <[email protected]> Date: Mon, Aug 30, 2010 at 6:47 PM Subject: Re: [Tinyos-help] Blip on IRIS reset problem To: Miklos Maroti <[email protected]> IS THE SAME TRICK STILL WORKING FOR HIM ? OR THAT WORKED ONLY ONCE IN THE FIRST TIME > ? REGARDS NITHIN KEEN On Mon, Aug 30, 2010 at 6:25 PM, Miklos Maroti <[email protected]>wrote: > Hi! > > This is where the original post of Zsolt comes in. You should start > the PC with the MIB520 connected and the IRIS removed, and while it is > running then connect the IRIS mote to the mib520, that worked for him > and we have no idea what is going on. Why a simple reset would not > result in the same behaviour. > > Miklos > > On Mon, Aug 30, 2010 at 2:52 PM, nithin k n <[email protected]> > wrote: > > HI , I did install the new version of tinyos, and everything worked > except a > > problem while starting the base station driver , i burnt a mote with > UDPEcho > > and other with IPBaseStation . the problem is in starting the driver. > > > > check out the screenshot attached which says the problem. > > > > Regards, > > Nithin keen > > > > On Mon, Aug 30, 2010 at 1:14 PM, Miklos Maroti <[email protected] > > > > wrote: > >> > >> Hi! > >> > >> Use the latest SVN vesrion of tinyos, not the one you have installed > >> from tar/rpm. > >> > >> Miklos > >> > >> On Mon, Aug 30, 2010 at 6:30 AM, nithin k n <[email protected]> > >> wrote: > >> > attached screenshots supports the problem statement what i reffered > >> > to... > >> > > >> > ---------- Forwarded message ---------- > >> > From: nithin k n <[email protected]> > >> > Date: Mon, Aug 30, 2010 at 9:53 AM > >> > Subject: Re: [Tinyos-help] Blip on IRIS reset problem > >> > To: [email protected], > [email protected], > >> > [email protected], Miklos Maroti <[email protected] > > > >> > > >> > > >> > HI ALL ... > >> > HI Zsolt , in my case the official IPBaseStation is itself not > >> > gettin > >> > installed. > >> > when i give "make iris install mib520,/dev/ttyUSB0" the errors appear > >> > related to cc2420 interfaces and wirings associated with > BaseStationP.nc > >> > , > >> > like in CC2420Config and CC2420ControlC. > >> > > >> > can u suggest me what should i do? i thought like i should go for > making > >> > changes in BaseStationp.nc code , (i.e., changing cc2420's interfaces > >> > and > >> > wirings to rf230's interfaces and wirings) BECAUSE, IRIS XM2110 > DOESN'T > >> > HAS > >> > CC2420, RATHER IT IS WITH RF230 RADIO. > >> > If you think its some other way to the solution, then please send me > >> > the > >> > IPBaseStation code (/opt/tinyos-2.x/apps/IPBaseStation) , atleast I'll > >> > check > >> > it. > >> > > >> > Regards, > >> > Nithin keen > >> > On Sun, Aug 29, 2010 at 2:04 AM, Miklos Maroti > >> > <[email protected]> > >> > wrote: > >> >> > >> >> miklos > >> >> > >> >> > >> >> ---------- Forwarded message ---------- > >> >> From: Zsolt Szabó <[email protected]> > >> >> Date: 2010/8/6 > >> >> Subject: [Tinyos-help] Blip on IRIS reset problem > >> >> To: [email protected] > >> >> > >> >> > >> >> Hi all. > >> >> > >> >> I managed to get the Iris mote to work with the IPBaseStation and > blip > >> >> driver, but quite a tricky way. I am using a mib520CA programmer for > >> >> communication interface. When i plug the programmer in and attach the > >> >> mote onto it the led2 will light. But when starting the driver on pc > >> >> the led light goes off, or even before all flashes up then go off. > >> >> After this using the programmer's reset switch does not seem to help, > >> >> just detacthing and reattaching the mote. In this case the led2 turns > >> >> on as default. I even tried doing this with disabling all the leds > and > >> >> just enable one specific led in the Boot.booted event. I always got > >> >> the same result. After strarting blip driver, the mote halts, that > >> >> means it does not reboot itself, and i can't do that either manually > >> >> using reset switch. Now the tricky part. If i don't attach the mote > to > >> >> the programmer but start the blip driver on pc that tries to iniciate > >> >> communication i wait for 1 or sec while the driver tries to initiate > >> >> communication with the mote. Then i attach the mote and the blip is > >> >> functioning properly. I can even login via telnet onto the mote and > if > >> >> i want to i can even reset the device using the programmer's reset > >> >> switch. > >> >> What can be so spoiled in the IPBaseStation that the mote does not > >> >> accept even the hardware reset if the first (standard) case? > >> >> The phenomenon can be reproduced using unmodified, official tinyos > app > >> >> IPBaseStation and blip driver. > >> >> Have someone experiancing this reset problem? Does anybody have > >> >> suggestions for solving this issue? > >> >> > >> >> Regards > >> >> Zsolt > >> >> > >> >> _______________________________________________ > >> >> Tinyos-help mailing list > >> >> [email protected] > >> >> > >> >> > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > >> > > >> > > >> > > > > > >
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
