Cecelia, Sorry I'm coming into this late.
Link to the DASD as a differnent virtual device address. Virtual address 001 is on the same virtual controller as your virtual console (009), reader (00C),and punch (00D). Pick a virtual address not on this same virtual controller. If you use something like 100 that will be on a completely different virtual channel and so will be safe. If you stay on virtual channel Zero I'd have to look up the range for that virtual controller (it's probably 16 or 32). As for your spool space, I don't have access to an Installation Guide at the moment, so I can't give you any page references. I know you're doing this 1st level, so I'll tailor to that environment. There should have been a step where you formatted the volumes used for PAGE and SPOOL space. I don't know what was on the restore from DVD as far as the PAGE and SPOOL volumes is concerned, but I'd bet money that's where the source of the problem lies. In any case, since this is a clean install one easy thing to do is SPXTAPE your NSS's and such (unless you just want to rebuild them), shutdown CP & reformat your SPOOL volume (I'd probably do PAGE as well) with standalone ICKDSF, then IPL with a COLD start and reload anything you saved via SPXTAPE. If you're not up to standalone ICKDSF, use CPFMTXA while the system is up to prepare new volumes as SPOOL & PAGE. I'd use the same volids as the existing ones, relabel the existing ones to something else, then shutdown and IPL COLD. (If you don't like using the same volids then use different ones and make the necessary edits in SYSTEM CONFIG before you shutdown.) Wish I could have been there to help out! Brian Nielsen (Cecelia's former colleague) On Fri, 9 Dec 2005 16:55:17 -0000, Dusha, Cecelia, Ms., WHS/ITMD <[EMAIL PROTECTED]> wrote: >When I try to use the CP FLASHCOPY command I get an error message that >indicates the control unit does not support this function. The DS6800 has >the correct license because I can invoke the DSCLI commands for flashcopy on >the SMC... > >Any ideas what the problem could be? > >(I have tried using the website http://www.ibm.com/support/us/ for research, >but the elements that support VM do not appear to be up. Also I have tried >to access the website for the VM listserv to see if similar problems have >already been reported, but no luck in accessing that website. Although I >can see activity on the listserv from the emails discussing problems...) > >link $dasd$ 1000 1 rr >DASD 0001 LINKED R/O; R/W BY MAINT >Ready; T=0.01/0.01 06:33:25 >att 2000 * 2 >DASD 2000 ATTACHED TO MAINT 0002 WITH DEVCTL >Ready; T=0.01/0.01 06:33:35 >flashcopy 1 000 end 2 000 end >HCPNFC332E Invalid control unit type - 1 >Ready(00332); T=0.01/0.01 06:33:57 > >The HCPNFC332E message: >HCP332E Invalid control unit type - <rdev|vdev> > >Explanation: The device is attached to a control unit that is not valid for > >the entered command. The control unit does not support this function. > >System Action: The command is not executed. > >Operator Response: Enter the command again specifying the device number of >a device that is attached to a valid control unit. > >Note: The SET CACHE command cannot be entered for a 3880 Model 11 or 21. > > >The $DASD$ userid: >USER $DASD$ NOLOG >* ------ zVM 5.1 Volumes ------------------------ > MDISK 1000 3390 000 END 510RES MR xxxxxxxx xxxxxxxx xxxxxxxx > >Within the IOCP the DS6800 is defined as: >FICON CHPID PATH=(10),PCHID=110,TYPE=FC,SHARED > CHPID PATH=(11),PCHID=111,TYPE=FC,SHARED > CHPID PATH=(12),PCHID=112,TYPE=FC,SHARED > CHPID PATH=(13),PCHID=113,TYPE=FC,SHARED >FICON CHPID PATH=(14),PCHID=140,TYPE=FC,SHARED > CHPID PATH=(15),PCHID=141,TYPE=FC,SHARED > CHPID PATH=(16),PCHID=142,TYPE=FC,SHARED > CHPID PATH=(17),PCHID=143,TYPE=FC,SHARED >DASD CNTLUNIT CUNUMBR=100,PATH=(10,14,15,11),UNITADD=((00,256)), X > CUADD=0,UNIT=1750 > IODEVICE ADDRESS=(1000,256),UNIT=3390,CUNUMBR=100,PATH=10, X > STADET=Y,PART=VM1 >DASD CNTLUNIT CUNUMBR=200,PATH=(10,14,15,11),UNITADD=((00,256)), X > CUADD=8,UNIT=1750 > IODEVICE ADDRESS=(2000,256),UNIT=3390,CUNUMBR=200,PATH=10, X > STADET=Y,PART=(VM1,IFL) > >Thank you. > >Cecelia Dusha >WHS/ITMD/AEFDD >703-697-2305 >=========================================================================
