This one will work. https://www.adafruit.com/product/4364
Aug AG5AT Sent from my iPad > On Feb 8, 2021, at 3:53 PM, August Treubig <[email protected]> wrote: > > Too many on ebay are garbage clones. So find a legit 5 volt one. > You can wire rts to cts, etc. > Aug > AG5AT > > Sent from my iPad > >>> On Feb 8, 2021, at 3:30 PM, David Tiller <[email protected]> wrote: >>> >> Also, the CP2012 is not 5v tolerant. >> https://www.sparkfun.com/datasheets/IC/cp2102.pdf >> >>> On Feb 8, 2021, at 3:33 PM, Black Michael via wsjt-devel >>> <[email protected]> wrote: >>> >>> Hmmm..that's 4-wire...so ground, tx, rx, and 5V and wouldn't work with >>> hardware flow control. >>> >>> Mike W9MDB >>> >>> >>> >>> >>> On Monday, February 8, 2021, 01:33:11 PM CST, August Treubig >>> <[email protected]> wrote: >>> >>> >>> A din 6 pin and this will work fine. >>> >>> https://www.adafruit.com/product/954 >>> >>> No magic. Just a bit of soldering. >>> Aug >>> AG5AT >>> >>> Sent from my iPad >>> >>>>> On Feb 8, 2021, at 1:02 PM, Bill Somerville <[email protected]> wrote: >>>>> >>>> >>> >>> Hi Mike, >>> >>> there are several third-party replacements for the now unavailable IF-232C >>> module that is needed on this and other early Kenwood rigs. Most faithfully >>> replicate the original IF-232C, some may not. The manual is almost >>> certainly correct, the reporter, if he is correct, almost certainly has a >>> non-standard IF-232C replacement. >>> >>> 73 >>> Bill >>> G4WJS. >>> >>> On 08/02/2021 18:17, Black Michael via wsjt-devel wrote: >>>> The dude said "manual is wrong". >>>> >>>> Trying to get more information on serial cable to see if that's the cause. >>>> >>>> Old thread noticed a difference between cable types on a 450. Might have >>>> to do with RTS/CTS wiring differences and whether the cable supports >>>> hardware flow control. >>>> >>>> https://wsprnet.org/drupal/node/1307 >>>> >>>> Mike W9MDB >>>> >>>> >>>> On Monday, February 8, 2021, 12:06:48 PM CST, Bill Somerville >>>> <[email protected]> wrote: >>>> >>>> >>>> On 08/02/2021 17:45, Black Michael via wsjt-devel wrote: >>>> >>>> > Anybody with a TS-450S out there that is available for some testing? >>>> > >>>> > I've got somebody claiming it needs 1 stop bit and XONXOFF handshake >>>> > which I've never heard before and 2 stop bits and HARDWARE handshake >>>> > is the default setup and has been for years. >>>> > >>>> > Mike W9MDB >>>> >>>> Mike, >>>> >>>> >>>> according to the TS-450S/TS-690S CAT programming manual it is full >>>> duplex 4800 baud 8N2 with RTS/CTS flow control using TTL signal levels. >>>> I would be very surprised if that information was incorrect! >>>> >>>> 73 >>>> Bill >>>> G4WJS. >>> >>> _______________________________________________ >>> wsjt-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>> _______________________________________________ >>> wsjt-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >>> _______________________________________________ >>> wsjt-devel mailing list >>> [email protected] >>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel >> >> _______________________________________________ >> wsjt-devel mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/wsjt-devel > _______________________________________________ > wsjt-devel mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/wsjt-devel
