Thanks,
it works now!
I had to set the essid with sudo iwconfig set essid MyWlanName.
Then do a sudo dhclient to get a dhcp connection.
Perhaps not surprising, but:
Previously this was made automatically by a configuration option
wireless-essid in /etc/network/interfaces, but it doesn't seem to have
an effect with the zd1211rw driver. Also I have specified
iface eth1 inet dhcp, but that doesn't seem to do it.
Also I have problems with starting the driver automatically at startup.
I've put zd1211rw last in /etc/modules. I have to unplug the usb stick
before rebooting, and plug it in again after Linux has loaded, else it
fails: USB control request for firmware upload failed. Error number
-110. I suspect this has to do with zd1211rw being loaded too early in
the process, but I don't know to fix it. What is the proper way to load
the modules, is /etc/modules the right thing?
But the driver seems to work fine!
Don't know how formal tests are required, but I suggest adding
{USB_DEVICE(0x13b1, 0x0024), .driver_info = DEVICE_ZD1211B}
to zd_usb.c
/Henrik Hjelte
On Fri, 2006-12-15 at 22:57 -0500, William Keaney wrote:
> Mine does this when it has not associated properly with the AP.
> Notice that the output if 'iwconfig' says "Access Point: Invalid".
> Are you using encryption on your AP? I find that 'iwconfig eth1 enc
> open' usually fixes the problem. Failing that, make sure it is using
> the correct key.
>
> On 12/15/06, athoslnx <[EMAIL PROTECTED]> wrote:
>
>
>
> Henrik Hjelte-2 wrote:
> >
> > I am trying to get my Linksys USB Network Adapter with Wi-Fi
> finder
> > Linksys WUSBF54G 13b1:0024 to work with zd1211rw. Previously
> I've had
> > success version getting it to work with the old zd1211
> driver.
> > I'm running Ubuntu feisty, which has kernel 2.6.19-7.
> > zd1211rw is snapshot 2006-12-14, with an edited zd_usb.c
> with a new
> > {USB_DEVICE(0x13b1, 0x0024), .driver_info = DEVICE_ZD1211B}
> >
> > I seem to get the usb adapter recognized, but the Bit Rate
> is only 1
> > Mb/s and I can't get an dhcp offer. I tried to set another
> bit rate with
> > iwconfig (sudo iwconfig eth1 rate 11M), but it doesn't
> change. The
> > output of iwconfig looks the same next time.
> >
> > Any ideas how I can get further or what I'm doing wrong?
> > /Henrik Hjelte
> >
> > dmesg:
> >
> > [ 1047.992000] usb 3-3: new high speed USB device
> > using ehci_hcd and address 8
> > [ 1048.124000] usb 3-3: configuration #1 chosen from 1
> > choice
> > [ 1048.156000] usb 3-3: firmware version 0x4810 and
> > device bootcode version 0x4802 differ
> > [ 1048.264000] zd1211rw 3-3:1.0: firmware version 4725
> > [ 1048.308000] zd1211rw 3-3:1.0: zd1211b chip 13b1:0024
> v4802
> > high00-14-bf AL2230_RF pa0 ----
> > [ 1048.308000] zd1211rw 3-3:1.0: eth1
> > [ 1048.432000] ADDRCONF(NETDEV_UP): eth1: link is not
> > ready
> >
> >
> > iwconfig:
> >
> > eth1 IEEE 802.11b/g ESSID:"O" Nickname:"zd1211"
> > Mode:Managed Frequency:2.412 GHz Access
> > Point: Invalid
> > Bit Rate=1 Mb/s
> > Link Quality:0 Signal level:0 Noise
> > level:0
> > Rx invalid nwid:0 Rx invalid crypt:0 Rx
> > invalid frag:0
> > Tx excessive retries:0 Invalid misc:0
> > Missed beacon:0
> >
> >
> >
> >
> >
>
> -------------------------------------------------------------------------
> > Take Surveys. Earn Cash. Influence the Future of IT
> > Join SourceForge.net 's Techsay panel and you'll get the
> chance to share
> > your
> > opinions on IT & business topics through brief surveys - and
> earn cash
> >
>
> http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> > _______________________________________________
> > Zd1211-devs mailing list - http://zd1211.ath.cx/
> > Unsubscribe:
> https://lists.sourceforge.net/lists/listinfo/zd1211-devs
> >
> >
> I have the same problem...............
> --
> View this message in context:
> http://www.nabble.com/zd1211rw-problems%2C-bit-rate%
> 2C-icwonfig-tf2829350.html#a7900561
> Sent from the zd1211-devs mailing list archive at Nabble.com.
>
>
>
> -------------------------------------------------------------------------
> Take Surveys. Earn Cash. Influence the Future of IT
> Join SourceForge.net's Techsay panel and you'll get the chance
> to share your
> opinions on IT & business topics through brief surveys - and
> earn cash
>
> http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> _______________________________________________
> Zd1211-devs mailing list - http://zd1211.ath.cx/
> Unsubscribe:
> https://lists.sourceforge.net/lists/listinfo/zd1211-devs
>
> -------------------------------------------------------------------------
> Take Surveys. Earn Cash. Influence the Future of IT
> Join SourceForge.net's Techsay panel and you'll get the chance to share your
> opinions on IT & business topics through brief surveys - and earn cash
> http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> _______________________________________________ Zd1211-devs mailing list -
> http://zd1211.ath.cx/ Unsubscribe:
> https://lists.sourceforge.net/lists/listinfo/zd1211-devs
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
Zd1211-devs mailing list - http://zd1211.ath.cx/
Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
