Re: [Elphel-support] Elphel 393 Question

Hi Oleg, Thank you for your help. However, I'm still having the same problem. On one of my elphels, when I use the recovery card it works fine but when I remove the card the feed is very laggy. Do you know what the issue is? Also, when I uploaded the files to ipaddress/update_software.html the

Re: [Elphel-support] Elphel 393 Question

via ssh? > > Oleg > > On Thu, Feb 22, 2018 at 7:38 AM, Mohamed Morsy <mmo...@redzone.com> wrote: > >> Hello Oleg, >> >> I was able to fix one of my elphels yesterday using the methods you >> suggested. Now I'm trying to do the same with my other one but when I

Re: [Elphel-support] Elphel 393 Question

10393 with 3.3V directly (Todd asked about > this recently)? In this case you can check the current. > > On Thu, Feb 22, 2018 at 9:44 AM, Mohamed Morsy <mmo...@redzone.com> wrote: > >> No it doesn't print anything at all. I can't connect via ssh. Is it >> possib

Re: [Elphel-support] Elphel 393 Question

flashed boot.bin. > > Oleg > > On Thu, Feb 22, 2018 at 10:38 AM, Mohamed Morsy <mmo...@redzone.com> > wrote: > >> The 2 leds (green and yellow) are on. I'm using power from a battery >> without the traco board. This is what I did with the 1st board. I also

Re: [Elphel-support] Elphel 393 Question

Is it possible the ip address of the elphel changed. If so, how do i find it? -Mohamed On Wed, Feb 21, 2018 at 1:52 PM, Mohamed Morsy <mmo...@redzone.com> wrote: > I have not used the mircro usb port. The default ip address has been > changed to 10.4.1.4. > > -Mohamed > &

Re: [Elphel-support] Elphel 393 Question

dresses like this: > https://wiki.elphel.com/wiki/Tmp_manual > *Change_default_ip_address* > > Regards, > Oleg > > On Wed, Feb 21, 2018 at 11:18 AM, Mohamed Morsy <mmo...@redzone.com> > wrote: > >> Hello Oleg, >> >> I was having some difficulties wit

Re: [Elphel-support] Elphel 393 Question

> On Wed, Feb 21, 2018 at 1:50 PM, Mohamed Morsy <mmo...@redzone.com> wrote: > >> actually i think i found my answer. >> >> Thanks! >> >> On Wed, Feb 21, 2018 at 3:44 PM, Mohamed Morsy <mmo...@redzone.com> >> wrote: >> >>> ok so the i

Re: [Elphel-support] Elphel 393 Question

(incomplete) 10.4.1.4 is that elphel's ip. Do you know how to resolve this issue? Thanks, Mohamed Morsy On Tue, Feb 20, 2018 at 12:49 PM, Oleg <support-list@support.elphel.com> wrote: > Hi Mohamed, > > >> However, I'm still having the same problem. On one of my e

Re: [Elphel-support] Elphel 393 Question

actually i think i found my answer. Thanks! On Wed, Feb 21, 2018 at 3:44 PM, Mohamed Morsy <mmo...@redzone.com> wrote: > ok so the ip was 192.168.0.9. I changed it and it works. But when i power > it off and restart it, it goes back to 192.168.0.9. Do i have to save it > some

Re: [Elphel-support] Elphel 393 Question

gt; Get the serial console up and type: >>> >>>> root@elphel393:~# ifconfig >>> >>> >>> On Wed, Feb 21, 2018 at 1:08 PM, Mohamed Morsy <mmo...@redzone.com> >>> wrote: >>> >>>> Is it possible the ip address of the elphel c

[Elphel-support] Elphel 393 Question

Hello, I have 2 Elphel 393 boards and I believe both of their internal flash are corrupt or old. I am trying to update them. Do you have a link for the files or any instructions on how to do so? Thanks, Mohamed Morsy RedZone Robotics ___ Support-list

Re: [Elphel-support] Elphel 393 Question

3:~# overlay_sync 1 >>> root@elphel393:~# shutdown -hP now >> >> >> >> On Wed, Feb 21, 2018 at 1:50 PM, Mohamed Morsy <mmo...@redzone.com> >> wrote: >> >>> actually i think i found my answer. >>> >>> Thanks! >

Re: [Elphel-support] Elphel 393 Question

the corner on the card I'm using so it's like the recovery card. Do you know what the issue might be? Thanks, Mohamed On Thu, Feb 22, 2018 at 2:08 PM, Mohamed Morsy <mmo...@redzone.com> wrote: > That worked. Thanks > > On Thu, Feb 22, 2018 at 1:04 PM, Oleg <support-list@support.e

Re: [Elphel-support] Elphel Storage Drive

Hi Oleg, I formatted the drive using ip_address/format_disk.php. This created sda1 and raw sda2. Then I used mkfs.ext4 /dev/sda2 to format the 2nd partition. I made a directory sda2 in mnt and mounted /dev/sda2 there. I can copy files from /mnt/sda2 using scp. Is this the right way? I'm not sure

Re: [Elphel-support] Elphel Storage Drive

Oleg, Thank you. That worked. I was also having another problem. I've been using 14 MPix sensors. I followed the instructions on the new update and was able to get them to work. However, when I use this SSD, the sensors don't seem to work anymore. Is there a fix for this? Regards, Mohamed On

Re: [Elphel-support] Elphel Storage Drive

Oleg, I reformatted the drive so sda2 is raw. Now I'm trying to copy a recording from there. I'm not sure what you meant by: run https://git.elphel.com/Elphel/eyesis4pi-393-gui/blob/master/ footage_downloader/split_mov.php from inside the directory with image.bin Also, when I use the 14MPx

Re: [Elphel-support] Elphel Storage Drive

Also, how can I remove the files from the sda2 partition once I'm done? On Mon, Apr 9, 2018 at 2:26 PM, Mohamed Morsy <mmo...@redzone.com> wrote: > I'm using 3 sensors. Sometimes only one shows up (it isn't always the same > port). > > On Mon, Apr 9, 2018 at 1:58 PM,

Re: [Elphel-support] Elphel Storage Drive

I'm using 3 sensors. Sometimes only one shows up (it isn't always the same port). On Mon, Apr 9, 2018 at 1:58 PM, Oleg wrote: > Mohamed, > > >> I reformatted the drive so sda2 is raw. Now I'm trying to copy a >> recording from there. I'm not sure what you meant

[Elphel-support] Elphel Storage Drive

if you have some instructions? Thank you, Mohamed Morsy RedZone Robotics ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Re: [Elphel-support] Elphel 393 Nand upgrade

I replaced it with the 10385 board and now it works. Thanks. On Thu, Dec 13, 2018 at 4:21 PM Mohamed Morsy wrote: > There are no sensors connected. I'm using direct 3.3V from a power supply. > I can try the 10385 board. > > On Thu, Dec 13, 2018 at 4:19 PM Oleg > wrote: > &g

Re: [Elphel-support] Elphel 393 Nand upgrade

e it stops is: [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr This is a Rev B Elphel running on a uSD card. Do you know what the issue might be? Thanks, Mohamed On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy wrote: > That worked. Thanks. > > Mohamed > > On Tu

Re: [Elphel-support] Elphel 393 Nand upgrade

No it does not boot from flash. The card does work with other boards. On Thu, Dec 13, 2018 at 3:46 PM Oleg wrote: > Hi Mohamed, > > Does the board boot fine from flash? > Does the same uSD card work with other rev B boards? > > On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy w

Re: [Elphel-support] Elphel 393 Nand upgrade

ply (how do you power the board? direct 3.3V or 48V via > 10385 board?) > * another power cable > > On Thu, Dec 13, 2018 at 1:50 PM Mohamed Morsy wrote: > >> No it does not boot from flash. >> The card does work with other boards. >> >> On Thu, Dec 13, 2018 at 3

Re: [Elphel-support] Elphel 393 Nand upgrade

u have any other ideas? >> >> >> Also I meant to send the previous email from my Redzone email so I'll CC >> myself to this chain. >> >> >> Thanks, >> >> >> Mohamed Morsy >> >> >> -- >&g

Re: [Elphel-support] 10393 Imagers Synchronization

Support Sent: Wednesday, May 8, 2019 3:48:29 PM To: Mohamed Morsy; Elphel List Subject: Re: [Elphel-support] 10393 Imagers Synchronization Hello Mohammed, You can save camera settings so they will be precisely synchronized. In "free running" mode each sensor can have different

[Elphel-support] 10393 Imagers Synchronization

? If this is something you've tested please let me know. Thank you, Mohamed Morsy RedZone Robotics ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com