Re: [Elphel-support] An error in replacing the 14-megapixel sensor(mt9f002) by 5-megapixel sensor(mt9006)

2020-10-20 Thread Oleg 
Ali,

I see. So, you just need to go http://community.elphel.com/bootblock393/ again
and put the correct data to make 5MPx work. See the attached image.
In short - in the AUX Board table - make sure, *Application* field is *MT9P006
*, and the *Application mode* is *15 *. Then hit "PROGRAM AUX" - it's slow,
so wait a bit (10 sec?). Then "READ AUX" to check the changes were made.

Then reboot the camera. And it should work. If not, please send the
autocampars log again.

I want to back up the micro-SD card but it dose not mount on any OS; how to
> can I do it?

It will mount in any Linux OS. Simply copying the files will not work - you
need raw cloning - please, read about "dd"-utility.
If you have Windows only then it should see the BOOT partition - it's FAT.

Regards,
Oleg



On Tue, Oct 20, 2020 at 6:04 AM ali tamimi  wrote:

>
> Oleg,
> Everything is OK with "14 Mpix" sensor; but when I connect the "5 Mpix"
> no picture is seen at all. I'm sure that there is no problem with cable(it
> works well with "14 Mpix" sensor ). The micro-SD card marked "5MPx" is also
> insert to the slot too. I put the log files below.
> And another question. I want to back up the micro-SD card but it dose not
> mount on any OS; how to can I do it?
>
> *log files:*
> *The "Read AUX" output:*
> 
> Elphel
> 10389
> B
> F80008
> 1603185256
> Eyesis4pi393
> 1001
> 
>
> *The "autocampars.log" :*
> root@elphel393:~# cat /var/log/autocampars.log
> 00014.09 autocampars: initializing state file /var/volatile/state/camera
> 00014.27 autocampars: Application - Eyesis4pi393, mode: 1001
>
> 00014.30 autocampars: Processing camera state: BOOT
> 00014.33 autocampars: Got sensor map from sysfs:
> 0: mt9p006, none, none, none
> 1: mt9p006, none, none, none
> 2: mt9p006, none, none, none
> 3: mt9p006, none, none, none
> 00014.35 autocampars: Active sensor ports: 0,1,2,3 master_port = 0
> 00014.38 autocampars: Sensors map read from the sysfs: [mt9p006, none,
> none, none],[mt9p006, none, none, none],[mt9p006, none, none,
> none],[mt9p006, none, none, none]
> 00014.41 autocampars: Parsed existing ini file
> 00014.43 autocampars: get_application_mode()->1013623
> 00014.46 autocampars: Parsed existing ini file
> 00014.49 autocampars: Detecting sensors for Eyesis4pi393
> 00014.51 autocampars: Got --init command, initialization was not
> completed, just continue
> 00014.54 autocampars: detect_camera()
> 00014.56 autocampars: detect_camera():
> 0: mt9p006, none, none, none
> 1: mt9p006, none, none, none
> 2: mt9p006, none, none, none
> 3: mt9p006, none, none, none
> 00014.59 autocampars: ports:0, 1, 2, 3
> 00014.62 autocampars: boot
> 00014.64 autocampars: Parsed existing ini file
> 00014.67 autocampars: Using sensor mask 0xf
> 00016.95 autocampars: Setting sensors/multiplexers power
> 00016.98 autocampars: set_eyesis_power_control()=>Array
> (
> [result] => OK
> [retval] => 0
> )
>
> 00017.00 autocampars: GLOBALS['camera_state_arr']=>Array
> (
> [exit_stage] =>
> [state] => BOOT
> [rev10389] => B
> [application] => Eyesis4pi393
> [mode] => 1001
> [max_frame_time] => 30
> [is_slave] => 1
> [eyesis_top] => 1
> [is_eyesis] => 1
> [eyesis_power] => 1
> [max_latency] => 5
> )
>
> 00017.03 autocampars: Current state: BOOT
> 00017.06 autocampars: This is a slave camera - waiting for master to
> contol next steps
> 00017.08 autocampars: Log file saved as /var/log/autocampars.log
> 00017.11 autocampars: --
> root@elphel393:~#
>
> On Mon, Oct 19, 2020 at 10:18 PM Oleg 
> wrote:
>
>> Ali,
>>
>> 1. Please send the /var/log/autocampars.log. It can help to rule out a
>> possible misconfiguration. If everything is correct then one can assume
>> it's a bad cable.
>>
>> 2. (just want to double check your configuration) Go
>> http://community.elphel.com/bootblock393/, make sure the ip address in
>> the 1st table is correct, then click "Read AUX" in the "AUX board
>> (10389)"-table - what's the output?
>>
>> Regards,
>> Oleg
>>
>> On Mon, Oct 19, 2020 at 9:21 AM Elphel Support <
>> support-list@support.elphel.com> wrote:
>>
>>> Hello Ali,
>>>
>>> There should be no problems with impedance matching, we tested both
>>> types of sensors with up to 450mm cables (for ectremely long cable
>>> programmatic phase adjustment may be needed). And the cables are the same
>>> for both serial (14MPix) and parallel (5MPix).
>>>
>>> Andrey
>>>
>>>
>>>  On Mon, 19 Oct 2020 05:33:14 -0600 *ali tamimi
>>> >* wrote 
>>>
>>> Hello Oleg
>>> yes, i can 'ssh' to camera and also can send
>>> the/var/log/autocampars.log. The microSD card marked "5MPx" is also insert
>>> to the slot.
>>> We opened the camera. When closing the sensor cable was pressed slightly
>>> and deformed. I guess the cable is damaged. In the parts list of the "5
>>> MPx" sensor, FFC cable with model number 050-30-51B, is provided. But
>>> by connecting this cable, the sensor is not detected eaither.The
>>>

Re: [Elphel-support] An error in replacing the 14-megapixel sensor(mt9f002) by 5-megapixel sensor(mt9006)

2020-10-20 Thread ali tamimi 
Oleg,
Everything is OK with "14 Mpix" sensor; but when I connect the "5 Mpix"  no
picture is seen at all. I'm sure that there is no problem with cable(it
works well with "14 Mpix" sensor ). The micro-SD card marked "5MPx" is also
insert to the slot too. I put the log files below.
And another question. I want to back up the micro-SD card but it dose not
mount on any OS; how to can I do it?

*log files:*
*The "Read AUX" output:*

Elphel
10389
B
F80008
1603185256
Eyesis4pi393
1001


*The "autocampars.log" :*
root@elphel393:~# cat /var/log/autocampars.log
00014.09 autocampars: initializing state file /var/volatile/state/camera
00014.27 autocampars: Application - Eyesis4pi393, mode: 1001

00014.30 autocampars: Processing camera state: BOOT
00014.33 autocampars: Got sensor map from sysfs:
0: mt9p006, none, none, none
1: mt9p006, none, none, none
2: mt9p006, none, none, none
3: mt9p006, none, none, none
00014.35 autocampars: Active sensor ports: 0,1,2,3 master_port = 0
00014.38 autocampars: Sensors map read from the sysfs: [mt9p006, none,
none, none],[mt9p006, none, none, none],[mt9p006, none, none,
none],[mt9p006, none, none, none]
00014.41 autocampars: Parsed existing ini file
00014.43 autocampars: get_application_mode()->1013623
00014.46 autocampars: Parsed existing ini file
00014.49 autocampars: Detecting sensors for Eyesis4pi393
00014.51 autocampars: Got --init command, initialization was not completed,
just continue
00014.54 autocampars: detect_camera()
00014.56 autocampars: detect_camera():
0: mt9p006, none, none, none
1: mt9p006, none, none, none
2: mt9p006, none, none, none
3: mt9p006, none, none, none
00014.59 autocampars: ports:0, 1, 2, 3
00014.62 autocampars: boot
00014.64 autocampars: Parsed existing ini file
00014.67 autocampars: Using sensor mask 0xf
00016.95 autocampars: Setting sensors/multiplexers power
00016.98 autocampars: set_eyesis_power_control()=>Array
(
[result] => OK
[retval] => 0
)

00017.00 autocampars: GLOBALS['camera_state_arr']=>Array
(
[exit_stage] =>
[state] => BOOT
[rev10389] => B
[application] => Eyesis4pi393
[mode] => 1001
[max_frame_time] => 30
[is_slave] => 1
[eyesis_top] => 1
[is_eyesis] => 1
[eyesis_power] => 1
[max_latency] => 5
)

00017.03 autocampars: Current state: BOOT
00017.06 autocampars: This is a slave camera - waiting for master to contol
next steps
00017.08 autocampars: Log file saved as /var/log/autocampars.log
00017.11 autocampars: --
root@elphel393:~#

On Mon, Oct 19, 2020 at 10:18 PM Oleg 
wrote:

> Ali,
>
> 1. Please send the /var/log/autocampars.log. It can help to rule out a
> possible misconfiguration. If everything is correct then one can assume
> it's a bad cable.
>
> 2. (just want to double check your configuration) Go
> http://community.elphel.com/bootblock393/, make sure the ip address in
> the 1st table is correct, then click "Read AUX" in the "AUX board
> (10389)"-table - what's the output?
>
> Regards,
> Oleg
>
> On Mon, Oct 19, 2020 at 9:21 AM Elphel Support <
> support-list@support.elphel.com> wrote:
>
>> Hello Ali,
>>
>> There should be no problems with impedance matching, we tested both types
>> of sensors with up to 450mm cables (for ectremely long cable programmatic
>> phase adjustment may be needed). And the cables are the same for both
>> serial (14MPix) and parallel (5MPix).
>>
>> Andrey
>>
>>
>>  On Mon, 19 Oct 2020 05:33:14 -0600 *ali tamimi
>> >* wrote 
>>
>> Hello Oleg
>> yes, i can 'ssh' to camera and also can send
>> the/var/log/autocampars.log. The microSD card marked "5MPx" is also insert
>> to the slot.
>> We opened the camera. When closing the sensor cable was pressed slightly
>> and deformed. I guess the cable is damaged. In the parts list of the "5
>> MPx" sensor, FFC cable with model number 050-30-51B, is provided. But by
>> connecting this cable, the sensor is not detected eaither.The connection
>> photo is sent in the attachment. Could there be a problem with the cable
>> (for example, impedance matching, etc.)?
>>
>> On Sun, Oct 18, 2020 at 11:23 AM Oleg 
>> wrote:
>>
>> Hello Ali,
>>
>> Can you 'ssh' to the camera? Could you send the /var/log/autocampars.log?
>>
>> ~$ ssh root@192.168.0.9 
>> ~# cat /var/log/autocampars.log
>>
>>
>> Or if you use minicom - send the boot log.
>>
>> If I remember right you should have a microSD card marked a "5MPx" - the
>> camera autoboots from the card - I suggest you try the card first. And the
>> only thing you will need is to set "MT9*P*006" from the bootblock393
>> page.
>>
>> Regards,
>> Oleg
>>
>> On Sun, Oct 18, 2020 at 7:56 AM ali tamimi  wrote:
>>
>> Hello
>> We have provided your product 10393. Your camera is very well designed
>> and made. Thank you for your good products and complete documentation
>> and your support.
>> Sensor installed on 10393 is a 14-megapixel sensor (10398) "mt9f002" by
>> default that Works well. We also bought

Re: [Elphel-support] An error in replacing the 14-megapixel sensor(mt9f002) by 5-megapixel sensor(mt9006)

2020-10-19 Thread Oleg 
Ali,

1. Please send the /var/log/autocampars.log. It can help to rule out a
possible misconfiguration. If everything is correct then one can assume
it's a bad cable.

2. (just want to double check your configuration) Go
http://community.elphel.com/bootblock393/, make sure the ip address in the
1st table is correct, then click "Read AUX" in the "AUX board
(10389)"-table - what's the output?

Regards,
Oleg

On Mon, Oct 19, 2020 at 9:21 AM Elphel Support <
support-list@support.elphel.com> wrote:

> Hello Ali,
>
> There should be no problems with impedance matching, we tested both types
> of sensors with up to 450mm cables (for ectremely long cable programmatic
> phase adjustment may be needed). And the cables are the same for both
> serial (14MPix) and parallel (5MPix).
>
> Andrey
>
>
>  On Mon, 19 Oct 2020 05:33:14 -0600 *ali tamimi
> >* wrote 
>
> Hello Oleg
> yes, i can 'ssh' to camera and also can send  the/var/log/autocampars.log.
> The microSD card marked "5MPx" is also insert to the slot.
> We opened the camera. When closing the sensor cable was pressed slightly
> and deformed. I guess the cable is damaged. In the parts list of the "5
> MPx" sensor, FFC cable with model number 050-30-51B, is provided. But by
> connecting this cable, the sensor is not detected eaither.The connection
> photo is sent in the attachment. Could there be a problem with the cable
> (for example, impedance matching, etc.)?
>
> On Sun, Oct 18, 2020 at 11:23 AM Oleg 
> wrote:
>
> Hello Ali,
>
> Can you 'ssh' to the camera? Could you send the /var/log/autocampars.log?
>
> ~$ ssh root@192.168.0.9 
> ~# cat /var/log/autocampars.log
>
>
> Or if you use minicom - send the boot log.
>
> If I remember right you should have a microSD card marked a "5MPx" - the
> camera autoboots from the card - I suggest you try the card first. And the
> only thing you will need is to set "MT9*P*006" from the bootblock393 page.
>
> Regards,
> Oleg
>
> On Sun, Oct 18, 2020 at 7:56 AM ali tamimi  wrote:
>
> Hello
> We have provided your product 10393. Your camera is very well designed and
> made. Thank you for your good products and complete documentation and
> your support.
> Sensor installed on 10393 is a 14-megapixel sensor (10398) "mt9f002" by
> default that Works well. We also bought the 10338 "mt9006" sensor. By
> replacing the sensors, the new one is not detectable and no image is seen.
> We downloaded the latest firmware, although the default sensor is
> "mt9006"  in the manual, the "devicetree.dtb" replacement process was
> performed according to the instructions,10393 nand flash was programmed
> but the sensor is not detected again.The image of error in web interface
> sent in the attachment. Thanks for your support in solving the problem.
> ___
> Support-list mailing list
> Support-list@support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
>
> ___
> Support-list mailing list
> Support-list@support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
>
>
> ___
> Support-list mailing list
> Support-list@support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>


-- 
Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783  x124
Elphel, Inc.
___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Re: [Elphel-support] An error in replacing the 14-megapixel sensor(mt9f002) by 5-megapixel sensor(mt9006)

2020-10-19 Thread Elphel Support 
Hello Ali,



There should be no problems with impedance matching, we tested both types of 
sensors with up to 450mm cables (for ectremely long cable programmatic phase 
adjustment may be needed). And the cables are the same for both serial (14MPix) 
and parallel (5MPix).



Andrey



 On Mon, 19 Oct 2020 05:33:14 -0600 ali tamimi  
wrote 


Hello Oleg

yes, i can 'ssh' to camera and also can send  the/var/log/autocampars.log. The 
microSD card marked "5MPx" is also insert to the slot.

We opened the camera. When closing the sensor cable was pressed  slightly and 
deformed. I guess the cable is damaged. In the parts list of the "5 MPx" 
sensor, FFC cable with model number 050-30-51B, is provided. But by connecting 
this cable, the sensor is not detected eaither.The connection photo is sent in 
the attachment. Could there be a problem with the cable (for example, impedance 
matching, etc.)?



On Sun, Oct 18, 2020 at 11:23 AM Oleg  
wrote:

Hello Ali,

Can you 'ssh' to the camera? Could you send the /var/log/autocampars.log?

~$ ssh http://mailto:root@192.168.0.9
~# cat /var/log/autocampars.log


Or if you use minicom - send the boot log.



If I remember right you should have a microSD card marked a "5MPx" - the camera 
autoboots from the card - I suggest you try the card first. And the only thing 
you will need is to set "MT9P006" from the bootblock393 page.



Regards,

Oleg



On Sun, Oct 18, 2020 at 7:56 AM ali tamimi  wrote:

Hello
We have provided your product 10393. Your camera is very well designed and 
made. Thank you for your good products and complete documentation and your 
support.

Sensor installed on 10393 is a 14-megapixel sensor (10398) "mt9f002" by default 
that Works well. We also bought the 10338 "mt9006" sensor. By replacing the 
sensors, the new one is not detectable and no image is seen.

We downloaded the latest firmware, although the default sensor is "mt9006"  in 
the manual, the "devicetree.dtb" replacement process was performed according to 
the instructions,10393 nand flash was programmed but the sensor is not detected 
again.The image of error in web interface sent in the attachment. Thanks for 
your support in solving the problem.


___
 Support-list mailing list
 mailto:Support-list@support.elphel.com
 http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com







___
Support-list mailing list 
mailto:Support-list@support.elphel.com 
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Re: [Elphel-support] An error in replacing the 14-megapixel sensor(mt9f002) by 5-megapixel sensor(mt9006)

2020-10-18 Thread Oleg 
Hello Ali,

Can you 'ssh' to the camera? Could you send the /var/log/autocampars.log?

> ~$ ssh root@192.168.0.9
> ~# cat /var/log/autocampars.log


Or if you use minicom - send the boot log.

If I remember right you should have a microSD card marked a "5MPx" - the
camera autoboots from the card - I suggest you try the card first. And the
only thing you will need is to set "MT9*P*006" from the bootblock393 page.

Regards,
Oleg

On Sun, Oct 18, 2020 at 7:56 AM ali tamimi  wrote:

> Hello
> We have provided your product 10393. Your camera is very well designed and
> made. Thank you for your good products and complete documentation and
> your support.
> Sensor installed on 10393 is a 14-megapixel sensor (10398) "mt9f002" by
> default that Works well. We also bought the 10338 "mt9006" sensor. By
> replacing the sensors, the new one is not detectable and no image is seen.
> We downloaded the latest firmware, although the default sensor is
> "mt9006"  in the manual, the "devicetree.dtb" replacement process was
> performed according to the instructions,10393 nand flash was programmed
> but the sensor is not detected again.The image of error in web interface
> sent in the attachment. Thanks for your support in solving the problem.
> ___
> Support-list mailing list
> Support-list@support.elphel.com
> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
>
___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

[Elphel-support] An error in replacing the 14-megapixel sensor(mt9f002) by 5-megapixel sensor(mt9006)

2020-10-18 Thread ali tamimi 
Hello
We have provided your product 10393. Your camera is very well designed and
made. Thank you for your good products and complete documentation and your
support.
Sensor installed on 10393 is a 14-megapixel sensor (10398) "mt9f002" by
default that Works well. We also bought the 10338 "mt9006" sensor. By
replacing the sensors, the new one is not detectable and no image is seen.
We downloaded the latest firmware, although the default sensor is "mt9006"
in the manual, the "devicetree.dtb" replacement process was performed
according to the instructions,10393 nand flash was programmed but the
sensor is not detected again.The image of error in web interface sent in
the attachment. Thanks for your support in solving the problem.
___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com