That could be, been a while. Does an rj45 fit in the daisychain input port? If so you need to use the middle port of the SyncPipe going to DaisyChain IN
Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Tue, Dec 29, 2015 at 8:04 PM, Bill Prince <[email protected]> wrote: > When the syncpipe is plugged into the sync injector, it gets power and > transfers data over through the ethernet cable (RJ45 at each end). > > bp > <part15sbs{at}gmail{dot}com> > > > On 12/29/2015 5:01 PM, Josh Luthman wrote: > > No POE. Both devices need power. The Syncpipe has a GPS module and does > timing on the 6p6c ports. > > Timing ports can be daisy chained (which is how SyncInjector gets timing). > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > On Dec 29, 2015 7:53 PM, "Scott Vander Dussen" <[email protected]> > wrote: > >> OK, so the SyncInjector provides PoE from its “SyncPipe or Daisy Chain >> In” RJ45 port, and that plugs into the center RJ45 port of the SyncPipe? >> So the SyncPipe receives PoE from the SyncInjector and sends timing back >> though that same cable? I tried that and it didn’t work :/ >> >> >> >> *From:* Af [mailto:[email protected]] *On Behalf Of *Josh Luthman >> *Sent:* Tuesday, December 29, 2015 16:49 >> *To:* [email protected] >> *Subject:* Re: [AFMUG] SyncInjector n00b question >> >> >> >> Correct. RJ45 simply won't fit on the outside ones. >> >> >> >> It will have one of the LEDs on when it's powered/booted if memory >> serves. Maybe green? I think the amber blinks every second or three to >> let you know it's good to go...something like that... >> >> >> >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> >> >> >> On Tue, Dec 29, 2015 at 7:46 PM, Steve Utick <[email protected]> wrote: >> >> And, I believe it needs to be plugged into the center jack on the >> SyncPipe as well, not the side ones. The side ones are 6p6c connectors to >> provide sync to a A/P by sync cable. >> >> >> >> On Tue, Dec 29, 2015 at 5:44 PM, Josh Luthman < >> <[email protected]>[email protected]> wrote: >> >> Syncpipe needs power. Up to 50v? >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> >> On Dec 29, 2015 7:18 PM, "Scott Vander Dussen" <[email protected]> >> wrote: >> >> Trying to use a SyncInjector to provide timing over power to a mix of >> 100/450APs. >> >> >> >> Gigabit SyncInjector revision I0, SyncPipe Deluxe revision H1 both >> receiving 27vdc. SyncPipe timing port directly to APs timing port works >> fine. SyncPipe timing port to SyncInjector “SyncPipe or Daisy Chain In” >> port does not seem to work. (see syncinjector.jpg) I’ve tried two >> SyncInjectors with the same results. If the SyncInjector is receiving sync >> from the SyncPipe, should I see the value column populated? (See site >> monitor string.png) >> >> >> >> Is there any configuration I need to change for the >> SyncInjector/SiteMonitor to make this combo work? Thanks in advance. >> >> >> >> >> > >
