Hmm, so how far does the connection go? Do the modems train up? You might want to go through http://www.cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a0 080094eb9.shtml or http://www.cisco.com/en/US/tech/tk713/tk507/technologies_tech_note09186a 008019cfa7.shtml oli
________________________________ From: Mad Unix [mailto:[EMAIL PROTECTED] Sent: Wednesday, July 09, 2008 11:25 AM To: Oliver Boehmer (oboehmer) Cc: [email protected] Subject: Re: [c-nsp] Analog Dialer I have added this but it didnt help it keeps trying to connect to authenticate then failed SDC_R2#conf t Enter configuration commands, one per line. End with CNTL/Z. SDC_R2(config)#line 450 473 SDC_R2(config-line)#exec-timeout 0 0 SDC_R2(config-line)#modem Dialin SDC_R2(config-line)#transport input all SDC_R2(config-line)#autoselect during-login SDC_R2(config-line)#autoselect ppp SDC_R2(config-line)# SDC_R2(config-line)#exit SDC_R2(config)#exit SDC_R2#sh line Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int 0 0 CTY - - - - - 1 0 0/0 - Ready 1 1 AUX 9600/9600 - - - - - 0 0 0/0 - Ready I 0/450 450 TTY - DialIn - - - 0 0 0/0 - Idle I 0/451 451 TTY - DialIn - - - 0 0 0/0 - Idle I 0/452 452 TTY - DialIn - - - 0 0 0/0 - Idle I 0/453 453 TTY - DialIn - - - 0 0 0/0 - Idle I 0/454 454 TTY - DialIn - - - 0 0 0/0 - Idle I 0/455 455 TTY - DialIn - - - 0 0 0/0 - Idle I 0/456 456 TTY - DialIn - - - 0 0 0/0 - Idle I 0/457 457 TTY - DialIn - - - 0 0 0/0 - Idle I 0/458 458 TTY - DialIn - - - 0 0 0/0 - Idle I 0/459 459 TTY - DialIn - - - 0 0 0/0 - Idle I 0/460 460 TTY - DialIn - - - 0 0 0/0 - Idle I 0/461 461 TTY - DialIn - - - 0 0 0/0 - Idle I 0/462 462 TTY - DialIn - - - 0 0 0/0 - Idle I 0/463 463 TTY - DialIn - - - 0 0 0/0 - Idle I 0/464 464 TTY - DialIn - - - 0 0 0/0 - Idle I 0/465 465 TTY - DialIn - - - 0 0 0/0 - Idle I 0/466 466 TTY - DialIn - - - 0 0 0/0 - Idle I 0/467 467 TTY - DialIn - - - 0 0 0/0 - Idle I 0/468 468 TTY - DialIn - - - 0 0 0/0 - Idle I 0/469 469 TTY - DialIn - - - 0 0 0/0 - Idle I 0/470 470 TTY - DialIn - - - 0 0 0/0 - Idle I 0/471 471 TTY - DialIn - - - 0 0 0/0 - Idle I 0/472 472 TTY - DialIn - - - 0 0 0/0 - Idle I 0/473 473 TTY - DialIn - - - 0 0 0/0 - Idle * 706 706 VTY - - - - - 50 0 0/0 - Ready * 707 707 VTY - - - - - 9 0 0/0 - Ready 708 708 VTY - - - - - 1 0 0/0 - Ready 709 709 VTY - - - - - 0 0 0/0 - Idle 710 710 VTY - - - - - 0 0 0/0 - Idle Line(s) not in async mode -or- with no hardware support: 2-449, 474-705 regarding the CEF we have disabled becuase it was disconnecting the Dialer after atime... so we added this no ip route-cache cef interface Serial4/0:15 no ip address encapsulation ppp no ip route-cache cef dialer rotary-group 1 dialer-group 2 isdn switch-type primary-net5 isdn incoming-voice modem isdn guard-timer 3000 ! interface Serial4/1:15 no ip address encapsulation ppp no ip route-cache cef dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 isdn incoming-voice modem isdn guard-timer 3000 ! On Wed, Jul 9, 2008 at 11:05 AM, Oliver Boehmer (oboehmer) <[EMAIL PROTECTED]> wrote: some patience, please :-) .. we all do this in our spare time.. The "line" config is missing (i.e. the lower part of the config). can you send this as well? Please re-enable CEF on the serial interface ("ip route-cache cef") oli ________________________________ From: Mad Unix [mailto:[EMAIL PROTECTED] Sent: Wednesday, July 09, 2008 10:31 AM To: Oliver Boehmer (oboehmer) Cc: [email protected] Subject: Re: [c-nsp] Analog Dialer Any updates On Wed, Jul 9, 2008 at 9:05 AM, Mad Unix <[EMAIL PROTECTED]> wrote: Am using interface Group-Async1 to accept analog calls for data transfer interface GigabitEthernet0/0 description $ES_LAN$ ip address 10.16.0.2 255.255.255.0 duplex auto speed auto media-type rj45 ! interface GigabitEthernet0/1 ip address 10.16.1.2 255.255.255.0 duplex auto speed auto media-type rj45 ! interface Serial0/0/0 description ---- Elect ---- ip address 10.14.11.5 255.255.255.252 ! interface Serial0/0/1 description --- Bank --- ip address 10.14.11.1 255.255.255.252 encapsulation ppp interface Serial4/0:15 no ip address encapsulation ppp no ip route-cache cef dialer rotary-group 1 dialer-group 2 isdn switch-type primary-net5 isdn incoming-voice modem isdn guard-timer 3000 ! interface Serial4/1:15 no ip address encapsulation ppp no ip route-cache cef dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 isdn incoming-voice modem isdn guard-timer 3000 ! interface Dialer1 description connected to Dial-inPCs(ISDN) ip address 10.13.1.1 255.255.255.0 encapsulation ppp no ip split-horizon dialer in-band dialer idle-timeout 3600 dialer-group 1 peer default ip address pool Cisco3662-Group-1 ppp authentication chap pap ms-chap callin ! interface Group-Async1 description connected tp Dial-in pcs (Analog) ip unnumbered GigabitEthernet0/0 encapsulation ppp no ip split-horizon dialer in-band dialer idle-timeout 3600 dialer-group 1 async mode interactive peer default ip address pool cisco3662-group-2 no fair-queue ppp authentication chap pap ms-chap callin group-range 0/450 0/473 ip http server ip http authentication local ip http timeout-policy idle 60 life 86400 requests 10000 ! ip radius source-interface GigabitEthernet0/0 access-list 2 permit 10.5.0.0 0.0.255.255 access-list 100 permit ip 10.4.0.0 0.0.255.255 10.13.0.0 0.0.255.255 access-list 100 permit ip 10.5.0.0 0.0.255.255 10.13.0.0 0.0.255.255 access-list 100 permit ip 10.5.0.0 0.0.255.255 10.0.0.0 0.255.255.255 access-list 101 permit tcp host 10.5.3.10 any eq telnet dialer-list 1 protocol ip permit dialer-list 2 protocol ip permit On Wed, Jul 9, 2008 at 8:39 AM, Oliver Boehmer (oboehmer) <[EMAIL PROTECTED]> wrote: Can't tell based on this config alone. can you please show the full config? (at least the one of the Serialx/y:z (the D-channel), any dialer interfaces and the "line" config at the end)? http://www.cisco.com/en/US/products/hw/univgate/ps505/products_configura tion_example09186a0080094a49.shtml <http://www.cisco.com/en/US/products/hw/univgate/ps505/products_configur ation_example09186a0080094a49.shtml> shows a sample AS5xxx config, which can easily be adapted to your environment.. oli Mad Unix <> wrote on Wednesday, July 09, 2008 8:27 AM: > have a PRI connecting 60 ppl using BRI and Analog calls > the Router 3800 PRI interface is having Digital modem to accept > analog phone calls > the analog callers cant connect! > What could be wrong? > > interface Group-Async1 > description connected tp Dial-in pcs (Analog) > ip unnumbered GigabitEthernet0/0 > encapsulation ppp > no ip split-horizon > dialer in-band > dialer idle-timeout 3600 > dialer-group 1 > async mode interactive > peer default ip address pool cisco3662-group-2 > no fair-queue > ppp authentication chap pap ms-chap callin > group-range 0/450 0/473 > -- > madunix > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ -- madunix -- madunix -- madunix _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
