I guarantee you that is one problem! In addition to WSJT-X I also use MacLoggerDX (MLDX). It has a "Radio" tab in the preferences and I noticed that it was pointing to my /dev folder for the usbserial port and driver that it uses. I looked in that /dev folder and found that there was another - the one that the SLUSB opens up. So, I took a wild-ass guess that was what I needed and - bingo - it worked. If you use MLDX, don't use that same port name - they can't be shared. The SLUSB has one of it's own and you should see it in the /dev folder. Take a look and see if in fact there is something similar to that. If so - give it a try. Let me know how it goes....
Jim On Wednesday, Jan 29, 2014, at Wednesday, 10:14 AM, Robert Nobis wrote: > Jim, > > Thank you. This might be my issue. Here are the settings in my ini file: > > CATdriver=/dev/rig > CATport=/dev/ttyUSB0 > CATportIndex=9 > > How were you able to determine your actual USBSERIAL name and location? > > 73, Bob > > Bob Nobis - N7RJN > Goodyear, AZ > [email protected] > > > On Jan 29, 2014, at 10:39 AM, Jim Bennett <[email protected]> wrote: > >> Bob - have you modified the WSJT-X.ini file to point it to your SLUSB stuff? >> I had the same issue trying to get my iMac (and my MacBook Air) to properly >> do rig control. Here is what I had to do in my situation - your USBSERIAL >> name and location may be different: >> >> CATdriver=/dev/cu.usbserial-A501XNHZ >> CATport=/dev/cu.usbserial-A501XNHZ >> >> Jim / W6JHB >> >> >> On Wednesday, Jan 29, 2014, at Wednesday, 9:06 AM, Robert Nobis wrote: >> >>> I am trying to setup WSJT-X for JT65 operation on my K3 and Mac but can't >>> seem to get the program to work. My audio card is a SignaLink USB. >>> >>> When I try to configure WSJT-X to interface to my K3, I always get the >>> message "Open Rig Failed". >>> >>> Does anyone have any suggestions on the proper setup of the K3 as well as >>> WSJT-X? >>> >>> Here is my K3 setup: >>> >>> K3 CONFIG settings: >>> AF GAIN HI >>> AF LIM nor 030 >>> LIN OUT nor 075 >>> PTT--KEY OFF-OFF >>> RS232 38400 b >>> SPKRS 2 >>> SPKR+PH NO >>> >>> K3 MENU Settings: >>> MIC SEL Line In >>> MIC+LIN Not APPL (I can't change this) >>> >>> Controls: >>> CMP 0 >>> MIC MIC LINE 20 >>> SQUELCH 0 >>> RF GAIN 50% >>> MODE USB >>> NB OFF >>> NR OFF >>> NTCH OFF >>> VOX OFF >>> AGC AGC-F >>> ALT OFF >>> PWR 50 Watts >>> >>> On the SignaLink USB I have the Tx and Rx gain set for 50% and DLY set to 0. >>> >>> Thanks and 73, >>> >>> Bob - >>> >>> Bob Nobis - N7RJN >>> Goodyear, AZ >>> [email protected] >>> >>> >>> >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >> >> > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
