Jim, BINGO I was trying to transmit outside the passband.
Thanks, 73, Bob - N7RJN On 1/29/14, 1:05 PM, "Jim Bennett" <[email protected]> wrote: >Bob, > >Glad to help and that your rig control is working. I had a devil of a >time getting it working on my end. Exchanged several emails with G4KLA >who wrote some of the install instructions. He was a big help to me. > >On my SLUSB I have both the Rx and Tx set at the 1:00 position, and the >DLY all the way counter CCW. Those are about the same settings you have, >so the SLUSB is good to go (you do have it jumpered correctly, right...? >:-) > >I also assume you are running the K3 in DATA-A mode? When you press the >Tune button in WSJT-X, does the K3's red TX light go on? > >I've re-jumpered my SLUSB so that I can run it with my KX3 so that's >about as far as I can go on the troubleshooting. One other thing I found >- if I tried to transmit JT9 or JT65 with my WSJT frequency set outside >of the transmit pass-band, I would get no RF out. So, that's something >else you can check. Make sure you are inside the area on the "waterfall" >where all the green stuff is displayed. > >Jim > >On Wednesday, Jan 29, 2014, at Wednesday, 11:24 AM, Robert Nobis wrote: > >> JIm, >> >> Thanks, I found the USBSERIAL name and modified the INI file. I changed >>my settings to the following: >> >> CATdriver=/dev/tty.usbserial-AD02DW0Z >> CATport=/dev/tty.usbserial-AD02DW0Z >> CATportIndex=9 >> >> >> I have now been able to transmit, although I noticed that I don¹t get >>any readout on the ALC - Not even one bar. Must still have something set >>wrong. >> >> Bob Nobis - N7RJN >> Goodyear, AZ >> [email protected] >> >> >> On Jan 29, 2014, at 11:25 AM, Jim Bennett <[email protected]> wrote: >> >>> I guarantee you that is one problem! In addition to WSJT-X I also use >>>MacLoggerDX (MLDX). It has a "Radio" tab in the preferences and I >>>noticed that it was pointing to my /dev folder for the usbserial port >>>and driver that it uses. I looked in that /dev folder and found that >>>there was another - the one that the SLUSB opens up. So, I took a >>>wild-ass guess that was what I needed and - bingo - it worked. If you >>>use MLDX, don't use that same port name - they can't be shared. The >>>SLUSB has one of it's own and you should see it in the /dev folder. >>>Take a look and see if in fact there is something similar to that. If >>>so - give it a try. Let me know how it goes.... >>> >>> Jim >>> >>> >>> On Wednesday, Jan 29, 2014, at Wednesday, 10:14 AM, Robert Nobis >>>wrote: >>> >>>> Jim, >>>> >>>> Thank you. This might be my issue. Here are the settings in my ini >>>>file: >>>> >>>> CATdriver=/dev/rig >>>> CATport=/dev/ttyUSB0 >>>> CATportIndex=9 >>>> >>>> How were you able to determine your actual USBSERIAL name and >>>>location? >>>> >>>> 73, Bob >>>> >>>> Bob Nobis - N7RJN >>>> Goodyear, AZ >>>> [email protected] >>>> >>>> >>>> On Jan 29, 2014, at 10:39 AM, Jim Bennett <[email protected]> wrote: >>>> >>>>> Bob - have you modified the WSJT-X.ini file to point it to your >>>>>SLUSB stuff? I had the same issue trying to get my iMac (and my >>>>>MacBook Air) to properly do rig control. Here is what I had to do in >>>>>my situation - your USBSERIAL name and location may be different: >>>>> >>>>> CATdriver=/dev/cu.usbserial-A501XNHZ >>>>> CATport=/dev/cu.usbserial-A501XNHZ >>>>> >>>>> Jim / W6JHB >>>>> >>>>> >>>>> On Wednesday, Jan 29, 2014, at Wednesday, 9:06 AM, Robert Nobis >>>>>wrote: >>>>> >>>>>> I am trying to setup WSJT-X for JT65 operation on my K3 and Mac but >>>>>>can't seem to get the program to work. My audio card is a SignaLink >>>>>>USB. >>>>>> >>>>>> When I try to configure WSJT-X to interface to my K3, I always get >>>>>>the message "Open Rig Failed". >>>>>> >>>>>> Does anyone have any suggestions on the proper setup of the K3 as >>>>>>well as WSJT-X? >>>>>> >>>>>> Here is my K3 setup: >>>>>> >>>>>> K3 CONFIG settings: >>>>>> AF GAIN HI >>>>>> AF LIM nor 030 >>>>>> LIN OUT nor 075 >>>>>> PTT--KEY OFF-OFF >>>>>> RS232 38400 b >>>>>> SPKRS 2 >>>>>> SPKR+PH NO >>>>>> >>>>>> K3 MENU Settings: >>>>>> MIC SEL Line In >>>>>> MIC+LIN Not APPL (I can't change this) >>>>>> >>>>>> Controls: >>>>>> CMP 0 >>>>>> MIC MIC LINE 20 >>>>>> SQUELCH 0 >>>>>> RF GAIN 50% >>>>>> MODE USB >>>>>> NB OFF >>>>>> NR OFF >>>>>> NTCH OFF >>>>>> VOX OFF >>>>>> AGC AGC-F >>>>>> ALT OFF >>>>>> PWR 50 Watts >>>>>> >>>>>> On the SignaLink USB I have the Tx and Rx gain set for 50% and DLY >>>>>>set to 0. >>>>>> >>>>>> Thanks and 73, >>>>>> >>>>>> Bob - >>>>>> >>>>>> Bob Nobis - N7RJN >>>>>> Goodyear, AZ >>>>>> [email protected] >>>>>> >>>>>> >>>>>> >>>>>> ______________________________________________________________ >>>>>> Elecraft mailing list >>>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>>>> Help: http://mailman.qth.net/mmfaq.htm >>>>>> Post: mailto:[email protected] >>>>>> >>>>>> This list hosted by: http://www.qsl.net >>>>>> Please help support this email list: http://www.qsl.net/donate.html >>>>> >>>>> >>>> >>>> ______________________________________________________________ >>>> Elecraft mailing list >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>> Help: http://mailman.qth.net/mmfaq.htm >>>> Post: mailto:[email protected] >>>> >>>> This list hosted by: http://www.qsl.net >>>> Please help support this email list: http://www.qsl.net/donate.html >>> >>> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
