Did you set the lacp_rate option? e.g: bonding mode=4 miimon=100 lacp_rate=1
The default is 0 or "slow" (30 sec). set to 1 (fast, 1 sec) and see if that makes any difference. On Thu, Mar 27, 2014 at 11:27 AM, Rupesh Basnet <[email protected]>wrote: > Hi George, > > First I tried mode 4(802.3ad) at first but LACP didn't formed at all. > > Regards, > -------- > Rupesh Basnet > > > On 03/28/2014 12:09 AM, George B. wrote: > > "I have configured my linux box on mode 0" > > Wouldn't you need to use mode 4? > > 802.3ad or 4 > > IEEE 802.3ad Dynamic link aggregation. Creates > aggregation groups that share the same speed and > duplex settings. Utilizes all slaves in the active > aggregator according to the 802.3ad specification. > > > > On Thu, Mar 27, 2014 at 10:44 AM, Rupesh Basnet <[email protected]>wrote: > >> Hi All, >> >> I have been trying LACP between Foundry and Linux machine since some days >> but not able to figure out the issue and resolve the issue. I didn't see >> much configurations thats needs to be done on foundry. I have configured my >> linux box on mode 0 and bonding seems to be up but still I am not able to >> pass traffic through it. >> >> Serveriron Configurations: >> >> interface ethernet 4/2 >> port-name **LACP-with-Linux*** >> no spanning-tree >> link-aggregate active >> ! >> interface ethernet 4/3 >> port-name **LACP-with-Linux*** >> no spanning-tree >> link-aggregate active >> ! >> >> >> SI#show version >> SW: Version 09.3.00eTD4 Copyright (c) 1996-2003 Foundry Networks, Inc. >> Compiled on Jun 28 2005 at 18:57:32 labeled as WXR09300e >> HW: ServerIronGT E-2 Router, SYSIF version 21, Serial #: Non-exist >> ========================================================================== >> SL 1: B0GMR WSM2 Management Module, SYSIF 2, M6, ACTIVE >> Serial #: CH39040033 >> 0 MB SHM, 2 Application Processors >> 16384 KB BRAM, SMC version 1, BM version 21 >> SW: (1)09.3.00eTF2 (2)09.3.00eTF2 >> ========================================================================== >> SL 4: J-BxGC16 JetCore Gig Copper Module, SYSIF 2 >> Serial #: CH33060779 >> 4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 8a >> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 12, version 0449 >> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 13, version 0449 >> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 14, version 0449 >> 32768 KB PRAM and 2M-Bit*1 CAM for IGC 15, version 0449 >> >> >> SI#show link-aggregate >> System ID: 000c.db5d.b066 >> Long timeout: 90, default: 90 >> Short timeout: 3, default: 3 >> Port [Sys P] [Port P] [ Key ] >> [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope] >> 4/2 1 1 483 Yes S Agg Syn Col Dis Def No Ope >> 4/3 1 1 483 Yes S Agg Syn Col Dis Def No Ope >> >> >> Status of linux machine: >> MII Status: up >> MII Polling Interval (ms): 30000 >> Up Delay (ms): 0 >> Down Delay (ms): 0 >> >> Slave Interface: eth0 >> MII Status: up >> Speed: 1000 Mbps >> Duplex: full >> Link Failure Count: 0 >> Permanent HW addr: 00:e0:ed:2b:a1:99 >> Slave queue ID: 0 >> >> Slave Interface: eth1 >> MII Status: up >> Speed: 1000 Mbps >> Duplex: full >> Link Failure Count: 0 >> Permanent HW addr: 00:e0:ed:2b:a1:98 >> Slave queue ID: 0 >> >> -- >> Regards, >> -------- >> Rupesh Basnet >> >> _______________________________________________ >> foundry-nsp mailing list >> [email protected] >> http://puck.nether.net/mailman/listinfo/foundry-nsp >> > > >
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
