Hi George,
lacp_rate was set to slow. I tried changing it to fast as well but still
couldn't get any success.
Regards,
--------
Rupesh Basnet
On 03/28/2014 12:17 AM, George B. wrote:
Did you set the lacp_rate option?
e.g: bonding mode=4miimon=100lacp_rate=1
The default is 0 or "slow" (30 sec). set to 1 (fast, 1 sec) and see if
that makes any difference.
On Thu, Mar 27, 2014 at 11:27 AM, Rupesh Basnet <[email protected]
<mailto:[email protected]>> wrote:
Hi George,
First I tried mode 4(802.3ad) at first but LACP didn't formed at all.
Regards,
--------
Rupesh Basnet
On 03/28/2014 12:09 AM, George B. wrote:
"I have configured my linux box on mode 0"
Wouldn't you need to use mode 4?
802.3ad or 4
IEEE 802.3ad Dynamic link aggregation. Creates
aggregation groups that share the same speed and
duplex settings. Utilizes all slaves in the active
aggregator according to the 802.3ad specification.
On Thu, Mar 27, 2014 at 10:44 AM, Rupesh Basnet
<[email protected] <mailto:[email protected]>> wrote:
Hi All,
I have been trying LACP between Foundry and Linux machine
since some days but not able to figure out the issue and
resolve the issue. I didn't see much configurations thats
needs to be done on foundry. I have configured my linux box
on mode 0 and bonding seems to be up but still I am not able
to pass traffic through it.
Serveriron Configurations:
interface ethernet 4/2
port-name **LACP-with-Linux***
no spanning-tree
link-aggregate active
!
interface ethernet 4/3
port-name **LACP-with-Linux***
no spanning-tree
link-aggregate active
!
SI#show version
SW: Version 09.3.00eTD4 Copyright (c) 1996-2003 Foundry
Networks, Inc.
Compiled on Jun 28 2005 at 18:57:32 labeled as WXR09300e
HW: ServerIronGT E-2 Router, SYSIF version 21, Serial #:
Non-exist
==========================================================================
SL 1: B0GMR WSM2 Management Module, SYSIF 2, M6, ACTIVE
Serial #: CH39040033
0 MB SHM, 2 Application Processors
16384 KB BRAM, SMC version 1, BM version 21
SW: (1)09.3.00eTF2 (2)09.3.00eTF2
==========================================================================
SL 4: J-BxGC16 JetCore Gig Copper Module, SYSIF 2
Serial #: CH33060779
4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 8a
32768 KB PRAM and 2M-Bit*1 CAM for IGC 12, version 0449
32768 KB PRAM and 2M-Bit*1 CAM for IGC 13, version 0449
32768 KB PRAM and 2M-Bit*1 CAM for IGC 14, version 0449
32768 KB PRAM and 2M-Bit*1 CAM for IGC 15, version 0449
SI#show link-aggregate
System ID: 000c.db5d.b066
Long timeout: 90, default: 90
Short timeout: 3, default: 3
Port [Sys P] [Port P] [ Key ]
[Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
4/2 1 1 483 Yes S Agg Syn Col Dis
Def No Ope
4/3 1 1 483 Yes S Agg Syn Col Dis
Def No Ope
Status of linux machine:
MII Status: up
MII Polling Interval (ms): 30000
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth0
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 00:e0:ed:2b:a1:99
Slave queue ID: 0
Slave Interface: eth1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 00:e0:ed:2b:a1:98
Slave queue ID: 0
--
Regards,
--------
Rupesh Basnet
_______________________________________________
foundry-nsp mailing list
[email protected] <mailto:[email protected]>
http://puck.nether.net/mailman/listinfo/foundry-nsp
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp
