no you will have to go to the game controlers.
on that note you may have to config for each game so you will need to
launch the software.
At 08:53 a.m. 12/01/2011, you wrote:
Ok, Tom I did the following.
I plugged in the sgc 2909.
Then while the unit is plugged into the pc tower I went and installed the
drivers for it.
I then went and fired up TDV which does have force feedback in it.
I'm still getting the message on the lines that this does support force
feedback, but force feedback can not be initialized.
Where in the control panel do I go to try and turn force feedback back on?
I thought it would be somewhere down in the device manager. But no luck
there.
Any advice will be appreciated.
Many Thanks.
Ron who wonders if the SGC 2909 will work in a 64 bit world?
Ron Kolesar
[email protected]
--------------------------------------------------
From: "Thomas Ward" <[email protected]>
Sent: Monday, January 10, 2011 7:37 PM
To: "Gamers Discussion list" <[email protected]>
Subject: Re: [Audyssey] Sticks version game pads.
> Hi Ron,
>
> Hmmm...I don't know but the issue might be the fact you are running
> Windows 7 64. There is a lot of hardware that bugs out on Windows 7 64
> just because the drivers aren't there or well supported. All the same
> I'd say plug in your unit, install the software, and then go into the
> Windows control panel and make sure force feedback is enabled on the
> device. If you don't configure it through the control panel chances
> are things like ff will be turned off by default. If that doesn't work
> look for updated drivers/software that are Windows 7 64 compatible.
> Remember that device was released before Windows 7 came out.
>
> On 1/10/11, Ron Kolesar <[email protected]> wrote:
>> Here's to answering your question Tom.
>> I am running win 7 with a 64 bit processor.
>> I had the program that comes with the 2909 installed.
>> But every time I would fire up tdv I would get the message, something on
>> the
>> lines that the force feedback is turned off.
>> So I uninstalled the cd.
>> I don't know what I did wrong when I installed the drivers because I
>> installed the drivers just like I did when I originally purchased the
>> unit
>> when I was running vista 32 bit.
>> Any advice for reinstalling the program drivers?
>> Should I first plug in the 2909 then run the cd to install the drivers?
>> Please advise.
>> Ron
>
> ---
> Gamers mailing list __ [email protected]
> If you want to leave the list, send E-mail to
> [email protected].
> You can make changes or update your subscription via the web, at
> http://audyssey.org/mailman/listinfo/gamers_audyssey.org.
> All messages are archived and can be searched and read at
> http://www.mail-archive.com/[email protected].
> If you have any questions or concerns regarding the management of the
> list,
> please send E-mail to [email protected].
---
Gamers mailing list __ [email protected]
If you want to leave the list, send E-mail to [email protected].
You can make changes or update your subscription via the web, at
http://audyssey.org/mailman/listinfo/gamers_audyssey.org.
All messages are archived and can be searched and read at
http://www.mail-archive.com/[email protected].
If you have any questions or concerns regarding the management of the list,
please send E-mail to [email protected].
---
Gamers mailing list __ [email protected]
If you want to leave the list, send E-mail to [email protected].
You can make changes or update your subscription via the web, at
http://audyssey.org/mailman/listinfo/gamers_audyssey.org.
All messages are archived and can be searched and read at
http://www.mail-archive.com/[email protected].
If you have any questions or concerns regarding the management of the list,
please send E-mail to [email protected].
