At this summer's Longest Day at Nelson Ledges, our car had a wheel bearing noise that came and went during testing and qualifying, but never showed up in any of the conventional tests. We went so far as changing the entire rear end and all brakes, wheels and tires and it persisted. An hour and a half into the race, the left front bearing let go sending the car into a multi-revolution spin. It was slopping around so badly that the car had no brakes at the end of a straight section. Fortunately, the driver did an excellent job and we had a parts car in the pits.

Later on, I was talking with a well known endurance racer (actually borrowing a Cool Shirt cooler to replace ours [dead pump : ( ]). During our walk to his donor car, he told me he ran Miatas back in the old Firehawk series days and learned early on to never track Miata wheel bearings for more than 12 hours without replacement. Food for thought.

Our experience taught us that it doesn't necessarily have to test like a bad bearing to give the vibration and noise on the road/track. Obviously, in a SM car on track, there is less chance to hear bearing noise. YRMV

El Brown-O-


On Thursday, October 23, 2008, at 10:21 AM, [EMAIL PROTECTED] wrote:

I believe so on the fronts, but not sure.. haven't replaced them yet.

That didn't work on my car.. I jerked it in all directions loaded and unloaded, *no* slop.. but it made noise spinning it. I jacked the car up and idled it in 5th and it was a constant rrrrrrrrrrrrrrrrr noise emanating from the wheel area. Spinning the hub without brake hardware you could feel notchy-ness and hear the bearings. Even disassembly didn't indicate badness, but it was bad.

I've heard that too, but I don't subscribe.. it's no easier or cheaper to do it at the same time, the only thing you save is potential down time (do it all one day vs two half days). The argument goes that if the left wore out, the right isn't far behind.. but that's not always true. Something things I do agree (springs, shocks, tires, socks) but not for bearings. IMNSHO.

Wally


<image.tiff>Ross Kuhns <[EMAIL PROTECTED]>


<image.tiff>


or for the fronts you can just replace the whole hub correct?

To test you don't need to jack it up, we always give a good hard pull in a couple axis' at autox safety tests and you can tell a bad one - compare yours to another miata or two.


*on a side note, I saw where one of the track guys, oh it was Emilio, recommended always replacing the hubs in pairs, i.e. "if you do one side, do the other as well". Any idea why? I replaced one of my fronts last year, but not the other.



Ross Kuhns
<image.tiff>


Subject: Re: replacing wheel bearings
To: [EMAIL PROTECTED]
From: [EMAIL PROTECTED]
Date: Thu, 23 Oct 2008 08:52:29 -0400
CC: [EMAIL PROTECTED]; [EMAIL PROTECTED]; [email protected]


I just did a left rear, rumble with the top up, shake test had zero slop in any axis.. was bad, tho. Replaced and noise went away, car also tended to track lane crowns worse as the wheel would toe in/out as it interacted with the crown. That has lessened with the new bearing.

You either need a press or a gear puller. I found this writeup very helpful (and I had to use my oxy/acet torch to get the bearing race to move).

http://forum.miata.net/vb/showpost.php?p=1361125&postcount=14
http://forum.miata.net/vb/showpost.php?p=1361129&postcount=15

There was a secondary writeup that had pictures that helped a ton.. This is how I did it, and it worked fine (with the torch, race wouldn't move without it)

http://my.att.net/p/s/community.dll?ep=87&subpageid=222341&ck=

You may also need the snap ring.

Longer studs, I believe corvette ones work, but I don't rememebr more specifics.

Wallyman


<image.tiff>Ashraf Farrag <[EMAIL PROTECTED]>

<image.tiff>



> So now I'm suspecting the wheel bearings. Since the car is 10 years
> old and has 80K miles, 50+ track days, and 20+ autocrosses on it, I'm
> thinking maybe it's time to just do all of them.
>
Wheel bearings make a "rumbling" noise as it has been
described/characterized to me.

Shake/wobble test? Lift car, grab wheel at top and bottom and try to
wiggle and feel for play in the bearing. If there is play, you'll feel
it and it will sort of "click" but you should also make sure it isn't a
worn suspension joint. The FSM outlines a more precise test involving a
dial indicator gauge. Kind of expensive to replace all four if not
needed, IMHO but not a bad idea if the car is a track car. If you even
suspect wheel bearings, you should not be driving it.

Half-shafts and driveaxle checked?

--Ashraf
_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

<graycol.gif><pic00474.gif><ecblank.gif><C7504910.gif><C7595738.gif><C6 196514.gif><C5509330.gif><C3722995.gif><C2850767.gif><C2752546.gif><C52 09476.gif><C5279569.gif>_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

Reply via email to