John Hammer
Creative Director
SaySomethingImportant.com
Occasional Racecar Driver
-------- Original Message --------
Subject: Re: replacing wheel bearings
From: David Brown <[EMAIL PROTECTED]>
Date: Thu, October 23, 2008 1:50 pm
To: [email protected]
At this summer's Longest Day at Nelson Ledges, our car had a wheel
bearing noise that came and went during testing and qualifying, but
never showed up in any of the conventional tests. We went so far as
changing the entire rear end and all brakes, wheels and tires and it
persisted. An hour and a half into the race, the left front bearing let
go sending the car into a multi-revolution spin. It was slopping around
so badly that the car had no brakes at the end of a straight section.
Fortunately, the driver did an excellent job and we had a parts car in
the pits.
Later on, I was talking with a well known endurance racer (actually
borrowing a Cool Shirt cooler to replace ours [dead pump : ( ]).
During our walk to his donor car, he told me he ran Miatas back in the
old Firehawk series days and learned early on to never track Miata
wheel bearings for more than 12 hours without replacement. Food for
thought.
Our experience taught us that it doesn't necessarily have to test like
a bad bearing to give the vibration and noise on the road/track.
Obviously, in a SM car on track, there is less chance to hear bearing
noise. YRMV
El Brown-O-
On Thursday, October 23, 2008, at 10:21 AM, [EMAIL PROTECTED]
wrote:
> I believe so on the fronts, but not sure.. haven't replaced them yet.
>
> That didn't work on my car.. I jerked it in all directions loaded and
> unloaded, *no* slop.. but it made noise spinning it. I jacked the car
> up and idled it in 5th and it was a constant rrrrrrrrrrrrrrrrr noise
> emanating from the wheel area. Spinning the hub without brake hardware
> you could feel notchy-ness and hear the bearings. Even disassembly
> didn't indicate badness, but it was bad.
>
> I've heard that too, but I don't subscribe.. it's no easier or cheaper
> to do it at the same time, the only thing you save is potential down
> time (do it all one day vs two half days). The argument goes that if
> the left wore out, the right isn't far behind.. but that's not always
> true. Something things I do agree (springs, shocks, tires, socks) but
> not for bearings. IMNSHO.
>
> Wally
>
>
<image.tiff>Ross Kuhns <[EMAIL PROTECTED]>
>
>
<image.tiff>
>
>
> or for the fronts you can just replace the whole hub correct?
>
> To test you don't need to jack it up, we always give a good hard pull
> in a couple axis' at autox safety tests and you can tell a bad one -
> compare yours to another miata or two.
>
>
> *on a side note, I saw where one of the track guys, oh it was Emilio,
> recommended always replacing the hubs in pairs, i.e. "if you do one
> side, do the other as well". Any idea why? I replaced one of my fronts
> last year, but not the other.
>
>
>
> Ross Kuhns
<image.tiff>
>
>
> Subject: Re: replacing wheel bearings
> To: [EMAIL PROTECTED]
> From: [EMAIL PROTECTED]
> Date: Thu, 23 Oct 2008 08:52:29 -0400
> CC: [EMAIL PROTECTED]; [EMAIL PROTECTED];
> [email protected]
>
>
> I just did a left rear, rumble with the top up, shake test had zero
> slop in any axis.. was bad, tho. Replaced and noise went away, car
> also tended to track lane crowns worse as the wheel would toe in/out
> as it interacted with the crown. That has lessened with the new
> bearing.
>
> You either need a press or a gear puller. I found this writeup very
> helpful (and I had to use my oxy/acet torch to get the bearing race to
> move).
>
> http://forum.miata.net/vb/showpost.php?p=1361125&postcount=14
> http://forum.miata.net/vb/showpost.php?p=1361129&postcount=15
>
> There was a secondary writeup that had pictures that helped a ton..
> This is how I did it, and it worked fine (with the torch, race
> wouldn't move without it)
>
> http://my.att.net/p/s/community.dll?ep=87&subpageid=222341&ck=
>
> You may also need the snap ring.
>
> Longer studs, I believe corvette ones work, but I don't rememebr more
> specifics.
>
> Wallyman
>
>
<image.tiff>Ashraf Farrag <[EMAIL PROTECTED]>
>
<image.tiff>
>
>
>
> > So now I'm suspecting the wheel bearings. Since the car is 10 years
> > old and has 80K miles, 50+ track days, and 20+ autocrosses on it, I'm
> > thinking maybe it's time to just do all of them.
> >
> Wheel bearings make a "rumbling" noise as it has been
> described/characterized to me.
>
> Shake/wobble test? Lift car, grab wheel at top and bottom and try to
> wiggle and feel for play in the bearing. If there is play, you'll feel
> it and it will sort of "click" but you should also make sure it isn't a
> worn suspension joint. The FSM outlines a more precise test involving a
> dial indicator gauge. Kind of expensive to replace all four if not
> needed, IMHO but not a bad idea if the car is a track car. If you even
> suspect wheel bearings, you should not be driving it.
>
> Half-shafts and driveaxle checked?
>
> --Ashraf
> _______________________________________________
> Miatapower mailing list
> [email protected]
> http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
>
> <graycol.gif><pic00474.gif><ecblank.gif><C7504910.gif><C7595738.gif><C6
> 196514.gif><C5509330.gif><C3722995.gif><C2850767.gif><C2752546.gif><C52
> 09476.gif><C5279569.gif>_______________________________________________
> Miatapower mailing list
> [email protected]
> http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
_______________________________________________ Miatapower mailing list [email protected] http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
