Ike, I do have the schematics, but as far as I can tell, no parts layout. It does look like the parts are identified somewhat on the schematic.
We have a 36 channel, + 4 stereo channels, with 2 power supplies. Thanks for the input all, I'd rather not open a can of worms. Just want the pre amps to be usable. This is a new console (to us), and I'd say only 8 channels have pre amps that aren't super scratchy when the pot is turned. Repeatedly turning the pots has not resolved the issue. Andrew On Fri, Nov 4, 2011 at 7:40 AM, Ike Zimbel <[email protected]> wrote: > > Do you have a manual with the power supply schematic and (more > importantly) parts layout? Also, how many channels is your console and how > many power supplies do you have? > best, > Ike > > > On 11-11-03 11:36 PM, Andrew Nast wrote: > >> Thanks for all of the help! I've only replaced fuses on the power supply, >> how do you go about trimming the 18v rail? I'm going to look at my >> schematics in the morning to see about the DC action. >> >> >> >> >> On Nov 3, 2011, at 9:12 PM, "os" <[email protected] <mailto: >> [email protected]>> wrote: >> >> yes >>> >>> >>> -----Original Message----- >>> *From:* [email protected] >>> <mailto:neotek-owner@**analogbros.com <[email protected]>> >>> [mailto:neotek-owner@**analogbros.com <[email protected]> >>> <mailto:neotek-owner@**analogbros.com <[email protected]>>]*On >>> Behalf Of *Greg Norman >>> *Sent:* Thursday, November 03, 2011 11:05 PM >>> *To:* [email protected] <mailto:[email protected]> >>> *Subject:* Re: NEOTEK: Cleaning Pots on Neotek Elite >>> >>> >>> Did my last post go through? >>> >>> Greg Norman >>> On Nov 3, 2011, at 8:15 PM, Casey Rice wrote: >>> >>> Might want to do the DC thing and exercise each pot vigorously >>>> before deciding to use cleaner. >>>> >>>> Casey >>>> >>>> >>>> On 04/11/2011, at 11:54 AM, Jim Mikles wrote: >>>> >>>> In addition to cleaning, you may also need to null out the dc >>>>> across the pot. This dc varies as the gain pot is rotated >>>>> causing noise. On the Series 1 there is a trimpot for this, I >>>>> assume the Elite is similar, but I don't have a schematic. >>>>> Jim Mikles >>>>> >>>>> On 11/3/2011 8:35 PM, Andrew Nast wrote: >>>>> >>>>>> We have a Neotek Elite we recently installed, and every mic >>>>>> pre pot is super scratchy. I did some quick research, and >>>>>> bought two products; Deoxit Fader F5, and Deoxit Gold G5. >>>>>> Should I use both, or one of these products? Any tips on this >>>>>> procedure? I figure I need to pull each module and spray it in >>>>>> from the underneath. Going to wait for someones 2 cents before >>>>>> proceeding. Thanks in advance!! >>>>>> >>>>>> Andrew >>>>>> The Decibel Garden >>>>>> >>>>> ------ >>>>> >>>>> View the list online at: >>>>> >>>>> http://www.mail-archive.com/**[email protected]<http://www.mail-archive.com/[email protected]> >>>>> >>>>> You can unsubscribe at anytime by sending an email to >>>>> mailto:[email protected] with "unsubscribe neotek" in the >>>>> message body. If you have any difficulties, or questions >>>>> --please send an email to mailto:[email protected]. >>>>> >>>>> The Neotek list is lovingly hosted by Catapult Web. Remember >>>>> that any message or reply sent to the list will be >>>>> automatically forwarded to all subscribers. >>>>> >>>>> Vive Le Neotek! >>>>> >>>>> Thanks. >>>>> >>>> >>>> Casey Rice >>>> PO Box 423 >>>> Yarraville VIC 3013 >>>> +61 4 2367 2340 >>>> >>>> >>> > -- > Ike Zimbel, > Zimbel Audio Productions Ltd. > Toronto > 416-720-0887 > > "Studio House Calls". Repairs and upgrades to analog audio equipment > including: AMEK, dbx, Neve, Neotek, MCI, Soundcraft and more. Authorized > Warranty service for Allen& Heath, Clear-Com, Drawmer, Soundcraft, SPL and > Yamaha. Ask about our RF frequency co-ordination services! > www.zimbelaudio.com > > ------ > > View the list online at: http://www.mail-archive.com/** > [email protected] <http://www.mail-archive.com/[email protected]> > > You can unsubscribe at anytime by sending an email to mailto: > [email protected] with "unsubscribe neotek" in the message body. If > you have any difficulties, or questions --please send an email to mailto: > [email protected]. > > The Neotek list is lovingly hosted by Catapult Web. Remember that any > message or reply sent to the list will be automatically forwarded to all > subscribers. > > Vive Le Neotek! > > Thanks. >
