Ike, It doesn't appear that the back of the supplies have screw terminals. As far as I know, the console needs both supplies to run. (at least, firing up just one supply doesn't get it crackin. Perhaps it can be configured for one supply somehow?)
-Andrew On Fri, Nov 4, 2011 at 11:20 AM, Ike Zimbel <[email protected]> wrote: > > Do the power supplies have the screw terminals on the back? If so, you > can at least have easy access to take some voltage measurements. If the > +/-18 rails are out by very much, that's probably a big part of your > problem. Does the console need both supplies to be on to run? > best, > Ike > > > On 11-11-04 1:00 PM, Andrew Nast wrote: > >> Ike, >> >> I do have the schematics, but as far as I can tell, no parts layout. It >> does look like the parts are identified somewhat on the schematic. >> >> We have a 36 channel, + 4 stereo channels, with 2 power supplies. >> >> Thanks for the input all, I'd rather not open a can of worms. Just want >> the pre amps to be usable. This is a new console (to us), and I'd say only >> 8 channels have pre amps that aren't super scratchy when the pot is turned. >> Repeatedly turning the pots has not resolved the issue. >> >> Andrew >> >> >> >> On Fri, Nov 4, 2011 at 7:40 AM, Ike Zimbel <[email protected]<mailto: >> ike.zimbel@sympatico.**ca <[email protected]>>> wrote: >> >> >> Do you have a manual with the power supply schematic and (more >> importantly) parts layout? Also, how many channels is your console >> and how many power supplies do you have? >> best, >> Ike >> >> >> On 11-11-03 11:36 PM, Andrew Nast wrote: >> >> Thanks for all of the help! I've only replaced fuses on the >> power supply, how do you go about trimming the 18v rail? I'm >> going to look at my schematics in the morning to see about the >> DC action. >> >> >> >> >> On Nov 3, 2011, at 9:12 PM, "os" <[email protected] >> <mailto:[email protected]> <mailto:[email protected] >> >> <mailto:[email protected]>>> wrote: >> >> yes >> >> >> -----Original Message----- >> *From:* [email protected] >> <mailto:neotek-owner@**analogbros.com<[email protected]> >> > >> <mailto:neotek-owner@**analogbros.com<[email protected]> >> <mailto:neotek-owner@**analogbros.com<[email protected]> >> >> >> >> [mailto:neotek-owner@**analogbros.com<[email protected]> >> >> <mailto:neotek-owner@**analogbros.com<[email protected]> >> > >> <mailto:neotek-owner@**analogbros.com<[email protected]> >> >> <mailto:neotek-owner@**analogbros.com<[email protected]>>>]*On >> Behalf Of *Greg >> Norman >> *Sent:* Thursday, November 03, 2011 11:05 PM >> *To:* [email protected] >> <mailto:[email protected]> >> <mailto:[email protected] <mailto:[email protected]>** >> > >> >> *Subject:* Re: NEOTEK: Cleaning Pots on Neotek Elite >> >> >> Did my last post go through? >> >> Greg Norman >> On Nov 3, 2011, at 8:15 PM, Casey Rice wrote: >> >> Might want to do the DC thing and exercise each pot >> vigorously >> before deciding to use cleaner. >> >> Casey >> >> >> On 04/11/2011, at 11:54 AM, Jim Mikles wrote: >> >> In addition to cleaning, you may also need to >> null out the dc >> across the pot. This dc varies as the gain pot >> is rotated >> causing noise. On the Series 1 there is a >> trimpot for this, I >> assume the Elite is similar, but I don't have a >> schematic. >> Jim Mikles >> >> On 11/3/2011 8:35 PM, Andrew Nast wrote: >> >> We have a Neotek Elite we recently >> installed, and every mic >> pre pot is super scratchy. I did some quick >> research, and >> bought two products; Deoxit Fader F5, and >> Deoxit Gold G5. >> Should I use both, or one of these >> products? Any tips on this >> procedure? I figure I need to pull each >> module and spray it in >> from the underneath. Going to wait for >> someones 2 cents before >> proceeding. Thanks in advance!! >> >> Andrew >> The Decibel Garden >> >> ------ >> >> View the list online at: >> >> http://www.mail-archive.com/**[email protected]<http://www.mail-archive.com/[email protected]> >> >> You can unsubscribe at anytime by sending an >> email to >> mailto:[email protected] >> >> <mailto:imailsrv@analogbros.**com<[email protected]>> >> with "unsubscribe >> neotek" in the >> message body. If you have any difficulties, or >> questions >> --please send an email to >> mailto:[email protected] >> <mailto:[email protected]>. >> >> >> The Neotek list is lovingly hosted by Catapult >> Web. Remember >> that any message or reply sent to the list will be >> automatically forwarded to all subscribers. >> >> Vive Le Neotek! >> >> Thanks. >> >> >> Casey Rice >> PO Box 423 >> Yarraville VIC 3013 >> +61 4 2367 2340 <tel:%2B61%204%202367%202340> >> >> >> >> >> -- Ike Zimbel, >> Zimbel Audio Productions Ltd. >> Toronto >> 416-720-0887 <tel:416-720-0887> >> >> >> "Studio House Calls". Repairs and upgrades to analog audio >> equipment including: AMEK, dbx, Neve, Neotek, MCI, Soundcraft and >> more. Authorized Warranty service for Allen& Heath, Clear-Com, >> Drawmer, Soundcraft, SPL and Yamaha. Ask about our RF frequency >> co-ordination services! >> www.zimbelaudio.com <http://www.zimbelaudio.com> >> >> >> ------ >> >> View the list online at: >> >> http://www.mail-archive.com/**[email protected]<http://www.mail-archive.com/[email protected]> >> >> You can unsubscribe at anytime by sending an email to >> mailto:[email protected] >> <mailto:imailsrv@analogbros.**com<[email protected]> >> > >> >> with "unsubscribe neotek" in the message body. If you have any >> difficulties, or questions --please send an email to >> mailto:[email protected] <mailto:[email protected]>. >> >> >> The Neotek list is lovingly hosted by Catapult Web. Remember that >> any message or reply sent to the list will be automatically >> forwarded to all subscribers. >> >> Vive Le Neotek! >> >> Thanks. >> >> >> > -- > Ike Zimbel, > Zimbel Audio Productions Ltd. > Toronto > 416-720-0887 > > "Studio House Calls". Repairs and upgrades to analog audio equipment > including: AMEK, dbx, Neve, Neotek, MCI, Soundcraft and more. Authorized > Warranty service for Allen& Heath, Clear-Com, Drawmer, Soundcraft, SPL and > Yamaha. Ask about our RF frequency co-ordination services! > www.zimbelaudio.com > > ------ > > View the list online at: http://www.mail-archive.com/** > [email protected] <http://www.mail-archive.com/[email protected]> > > You can unsubscribe at anytime by sending an email to mailto: > [email protected] with "unsubscribe neotek" in the message body. If > you have any difficulties, or questions --please send an email to mailto: > [email protected]. > > The Neotek list is lovingly hosted by Catapult Web. Remember that any > message or reply sent to the list will be automatically forwarded to all > subscribers. > > Vive Le Neotek! > > Thanks. >
