I have a netlist- My guess is that unless you can somehow attach the track to the original netlist, it is ignored.
Thanks again for all the responses. ----- Original Message ----- From: "Dennis Saputelli" <[EMAIL PROTECTED]> To: "Protel EDA Forum" <[EMAIL PROTECTED]> Sent: Saturday, March 20, 2004 1:17 PM Subject: Re: [PEDA] Advanced PCB / Advanced Route 3.0 > it doesn't sound like you have a netlist, do you? > > so while we are strolling down memory lane ... > how about MAXROUTE ? > had a protel interface and > would only run on windows 2.0 (win 3.0 was too advanced) > > fortunately you could quit win 2.0 and it would drop > back to the good 'ol DOS prompt where you could get some > actual work done > > Dennis Saputelli > > > Jim Labrecque wrote: > > > > The problem is that the preroutes aren't even recognized by Advanced PCB- > > > > Another example- > > > > If I take the PCB design in Advanced PCB and draw a square out of a series > > of tracks on the top layer and then import it into Advanced Route- Advance > > Route doesn't see the square- (what I mean is that physically is not there. It > > is as if I never placed any tracks). > > > > I appreciate all the responses. > > > > Thanks, Jim > > > > ----- Original Message ----- > > From: "Joe Sapienza" <[EMAIL PROTECTED]> > > To: "Protel EDA Forum" <[EMAIL PROTECTED]> > > Sent: Saturday, March 20, 2004 11:47 AM > > Subject: Re: [PEDA] Advanced PCB / Advanced Route 3.0 > > > > > I believe that If I remember correctly and I understand your question, all > > > you need do is select to lock all pre routes and then run the autorouter. > > > > > > > > > ----- Original Message ----- > > > From: "Jim Labrecque" <[EMAIL PROTECTED]> > > > To: "Protel EDA Forum" <[EMAIL PROTECTED]> > > > Sent: Saturday, March 20, 2004 11:36 AM > > > Subject: [PEDA] Advanced PCB / Advanced Route 3.0 > > > > > > > > > > I realize I am using old software, but it is all I have on hand- > > > > > > > > Does anyone know whether it is possible to manually lay down some tracks > > > > in Advanced PCB, and then have Advanced Route recognize these tracks > > > > when you open the design? > > > > > > > > What I am trying to do is some incremental routes with advanced route- > > > > > > > > For example, the first routing I am trying is to have Advanced Route route > > > > all of the voltage/gnds. This is a multilayer design with 4 planes > > > consisting of > > > > 3 voltage and 1 ground. > > > > > > > > I route the 3 voltages and grounds and then export the design back to > > > Advanced > > > > PCB for some cleanup- (ie shortening some of the stubs and adding > > > additional > > > > pads for connection into the plane on high current parts). > > > > > > > > I then save it so that I can import it back into Advanced Route and route > > > the > > > > rest of the signal tracks. > > > > > > > > However, after the design is loaded into Advanced Route, any additional > > > tracks > > > > or pads that I have added are not in the design- > > > > > > > > Anybody have any ideas or suggestions? > > > > > > > > Thanks, Jim > > > > > > -- > _______________________________________________________________________ > Integrated Controls, Inc. Tel: 415-647-0480 EXT 107 > 2851 21st Street Fax: 415-647-3003 > San Francisco, CA 94110 www.integratedcontrolsinc.com > > > * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To leave this list visit: * http://www.techservinc.com/protelusers/leave.html * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * Forum Guidelines Rules: * http://www.techservinc.com/protelusers/forumrules.html * * Browse or Search previous postings: * http://www.mail-archive.com/[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
