Mike,

I had the same comment about being in a project, why oh why does it have to
be this way? The option does not become available until you create a project
and move the PCB into it. Additionally I asked about a hierarchal tree of
commands based upon whatever one was working on, never got a response. These
types of issues are why I have in the past to switch companies out of the
competitor products and into P992. Seems this type of feature and thinking
may have a place and time but with more companies going to a contract
workforce, and spending lots of time getting them up to speed with a tool is
not in the cards.

Joe



----- Original Message ----- 
From: "Mike Reagan" <[EMAIL PROTECTED]>
To: "'Protel EDA Forum'" <[EMAIL PROTECTED]>
Sent: Wednesday, April 14, 2004 1:01 PM
Subject: Re: [PEDA] Need more software


> John
> See, now Ya'll dont read everything I write.  No, you can not disable
> Camtastic unless a project is open.  I only design PCB so the Project
Button
> is muted and can not be disabled.  Trust me .... I ve been thru this with
> tech support also
> Mike
>
>
>
>
>
> -----Original Message-----
> From: John A. Ross [Design] [mailto:[EMAIL PROTECTED]
> Sent: Wednesday, April 14, 2004 12:21 PM
> To: Protel EDA Forum
> Subject: Re: [PEDA] Need more software
>
>
> > -----Original Message-----
> > From: Mike Reagan [mailto:[EMAIL PROTECTED]
> > Sent: Wednesday, April 14, 2004 4:56 PM
> > To: 'Protel EDA Forum'
> > Subject: Re: [PEDA] Need more software
> >
> > snip <
>
> > Camtastic is a step in the right direction. Again I don't
> > like the integration. Specifically, I don't like the fact
> > that every time you generate gerbers it automatically pops
> > up.  Protel this is waist of my time.
>
> Mike
>
> You can disable this by telling it not to open output files after
> generated.
>
> Project Options, Output Options, Open output after compile, uncheck.
>
> I know that makes no sense because of this compile word.
>
> Ian drops hints about the poor choice of the word 'compile' quite
> regularly in his postings, but it is still there, perhaps in SP1 ? :-)
>
> As regards, net antennas & Camtastic, I just tried a board with a spare
> 2mm trace sticking out from a 1.2mm via and the PCB Design Check comes
> up clean. I am looking to see if it is me, or the tool before posting
> more.
>
>
> John
>
>
>
> * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
> * To post a message: mailto:[EMAIL PROTECTED]
> *
> * To leave this list visit:
> * http://www.techservinc.com/protelusers/leave.html
> *
> * Contact the list manager:
> * mailto:[EMAIL PROTECTED]
> *
> * Forum Guidelines Rules:
> * http://www.techservinc.com/protelusers/forumrules.html
> *
> * Browse or Search previous postings:
> * http://www.mail-archive.com/[EMAIL PROTECTED]
> * * * * * * * * * * * * * * * * * * * * * * * * * * * * *



* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/[EMAIL PROTECTED]
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to