Are you saying if you rev or drive the idle sticks at 2-3krpm?  The idle is
held high (prob around 2krpm) if the speed sensor is telling the car it is
moving.  However it would be hard for one to go faulty and output a pulsed
signal I would think.  This could explain the overrun problem too.  I found
that you could not brake down from 30 in 4th to 20 say, as soon as you
lifted off the brake it would accelerate on it's own! 

Are you sure about the idle speed also?  I say that as the XR2 instruments
are very inaccurate.. I had great fun tuning my idle to about 800 rpm, to
find that I'd actually done it to about 550 rpm when reading from the ECU
directly!

I'd be very tempted to disconnect the speed sensor and the Idle Speed
Control Valve, but bend the stop out a little and see how it runs as a test.
It won't transition brilliantly from cold but if you set it when it is warm
there should be no hesitation and so on driving normally.  If you do it this
way you may have to feather the throttle slightly when the car is cold, but
it will be hardly much in this weather.

I also wonder if your throttle POT is 100%, the hesitation may be it not
detecting the pump action which enriches the fuel mixture before the MAF can
keep up.

I see you mention you may have used a different ISCV - Jim may be able to
correct me but I recall there are two kinds from Ford that work in different
ways.  I know one could be used with MS, but the other couldn't (maybe),
either way they were vastly different.

Hope there are some pointers for you
Matthew




-----Original Message-----
From: [email protected] [mailto:[email protected]]
On Behalf Of Steve Kodz
Sent: 01 June 2010 12:29
To: [email protected]
Subject: [Quantum Owners] Poor idling/running Zetec

We're getting a very bad idle with the Zetec in Carole's 2+2.  With the idle
speed control valve connected from cold it will idle nicely at around
1000rpm, if just left to idle and warm through.  However if you rev, or
drive that car the best idle to can get is between 2-3,000 rpm, which isn't
great :(  The car also drives badly, having hesitation and then you fight
the engine on the over run.

It is a lot better with the ISCV disconnected, but still not great.  The
idle is still a bit high, being around 1,200 rpm and it still doesn't drive
that great.

We've tried resetting the ECU to re-program it and Geoff's cleaned all the
electrical contact and the ISCV.  Any ideas what else needs to be done to
get this ready before the HHII?

Regards,
Steve
--
www.h4-turbo.co.uk
www.quantumowners.co.uk
www.quantumcars.co.uk
www.quantumheritage.co.uk

--
You received this message because you are subscribed to the Google Groups
"Quantum Owners Group" group.
To post to this group, send email to [email protected] To
unsubscribe from this group, send email to
[email protected]
For more options, visit this group at
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is"
basis, without warranty or the implication thereof. Neither the Quantum
Owners Club nor the individuals associated with the Quantum Owners Club or
in the preparation of the above information shall have any liability to any
person or entity with respect to liability, loss, or damage caused or
alleged to be caused directly or indirectly by the instructions contained
within this or related message(s).

-- 
You received this message because you are subscribed to the Google Groups 
"Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners 
Club nor the individuals associated with the Quantum Owners Club or in the 
preparation of the above information shall have any liability to any person or 
entity with respect to liability, loss, or damage caused or alleged to be 
caused directly or indirectly by the instructions contained within this or 
related message(s).

Reply via email to