One thing I wish was a stand alone button that could be labeled QRP. I'm
always tuning up on 5 watts.
VERY simple macro will do this. Try assigning PC005; to one of your macro
buttons. I
do this already but with using DXLabs...they have programable macro buttons
available as
well. But you
You can set the radio to tune on 5 watts automatically. You can go to
the TUN PWR menu in CONFIG and rather than NOR set it to 5 watts. Then
whenever you enter the tune mode it will put out 5 watts. Then when you
are done tuning you'll still be set at whatever power you were before.
~Brett (KC7
Can you make the FM sound sweet? The FM sounds like you're listening to an
HT. It doesn't sound as rich as the other modes. Maybe giving the FM a
deeper sound. Maybe that's what I mean. I've heard VHF radios and the FM
sounds deeper/more base than the K3 unless I don't have something set right
on
I was going to say, all of that being complained about, can be set any
way you want. Try the SHIFT control on the front panel. Set the
crossover *anywhere you want it*. The SHIFT setting is remembered by
mode.
Being able to hear down there was specifically requested by some who
do not share your
Wes Stewart wrote:
>
> If I use my XG2 as a source into the K3 and set the SSB BW to the default
> settings for my 2.8KHz 8-pole filter (100Hz to 2.9KHz) the signal which is
> S9 at its peak is still S7 at zero beat. A 100 Hz beat note on the wrong
> sideband is still S3 and a 200 Hz beat is >
een told that this would be pretty easy
implement in DSP. So why not do it?
Wes N7WS
--- On Fri, 1/15/10, Julian, G4ILO wrote:
> From: Julian, G4ILO
> Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
> To: elecraft@mailman.qth.net
> Date: Friday,
Merv Schweigert wrote:
>
> I think that has been altered from really good suppression to just so so
> from the demand of users to go to the lower audio freqs. I complained
> about it in private and they shifted the offset a little to make it some
> better, for me I need the supression, not t
>
> 2) Since the new DSP mods extends the bandwidth down to minus DC, implement
> phasing detection to improve the opposite sideband rejection. Even without
> the bandwidth extension, the SSB opposite sideband rejection is not the
> greatest.
>
> Wes N7WS
>
I think that has been altered
If it's not too late I would like to add another couple of requests.
1) Add Accukey emulation so I can send CW with the K3.
2) Since the new DSP mods extends the bandwidth down to minus DC, implement
phasing detection to improve the opposite sideband rejection. Even without the
bandwidth ext
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: htt
> An KIO replacement board that has a direct computer connection via
> USB, with built in sound card function, built in CAT com port
> function etc. so that there is only one cable to the PC.
A very well-thought list and I'll second Mario's input, particularly a
USB-based KIO board as a universal
I'd still like to see Ultimatic as well as Iambic please.
HNY
73 de M0XDF, K3 #174
--
The secret of life is honesty and fair dealing. If you can fake that,
you've got it made. -Groucho Marx
__
Elecraft mailing list
Home: http://mailman.q
Hi Wayne,
Am 23. Dec 2009, um 10:02:02 schrieb Wayne Burdick:
> As we head into 2010, we'd like to refresh the master firmware list
> based on your input. Items already on the list have priority, of
> course, but this is a great opportunity to let us know what else is
> missing or could be
Pardon my bad grammar. When this happens on start-up, the PTT line from
the mike is not closed and neither is any key line.
Duncan Carter wrote:
> No, when it's happened on my K3, the PTT line should be open/clear and
> neither is a key line.
>
> Dunc, W5DC
>
> Grant Youngman wrote:
>
>> Do
No, when it's happened on my K3, the PTT line should be open/clear and
neither is a key line.
Dunc, W5DC
Grant Youngman wrote:
> Does the ERR PTT go away if the PTT line is unasserted after the error
> message appears?
>
> Grant/NQ5T
>
> On Dec 30, 2009, at 4:18 PM, Duncan Carter wrote:
>
>
Does the ERR PTT go away if the PTT line is unasserted after the error message
appears?
Grant/NQ5T
On Dec 30, 2009, at 4:18 PM, Duncan Carter wrote:
> I've found the same problem and this problem seems to be of recent origin.
>
> Dunc, W5DC
>
> Joe Planisky wrote:
>> Hi Wayne,
>>
>> One mo
I've found the same problem and this problem seems to be of recent origin.
Dunc, W5DC
Joe Planisky wrote:
> Hi Wayne,
>
> One more item for your list. I just ran into an "ERR PTT" situation
> and discovered that you can't turn the rig off while ERR PTT is
> showing. I.e. it doesn't respond
Hi Wayne,
One more item for your list. I just ran into an "ERR PTT" situation
and discovered that you can't turn the rig off while ERR PTT is
showing. I.e. it doesn't respond to pressing the POWER button. I
understand the need to disable most all functionality until the ERR
PTT is clear
sta Wayne Burdick
> Lähetetty: 23. joulukuuta 2009 20:02
> Vastaanottaja: Elecraft Reflector; elecr...@yahoogroups.com;
> elecraft...@yahoogroups.com
> Aihe: [Elecraft] K3 needs survey -- firmware and application software
>
> Hi all,
>
> As you probably know, we kee
Thanks for the input, everyone. I've saved all of your suggestions,
and no doubt we'll be reviewing and prioritizing well into 2010.
Probably time to end the thread, too.
Here's to a safe and happy new year!
73,
Wayne
N6KR
__
Elecraf
Fix strange LO/HI CUT interactions. (Or tell me that the way it works
is intentional or some limitation of the DSP algorithms used.)
Here are some examples of unexpected behavior with FW 3.68 in DATA-A
mode. Numbers in parentheses are the values I get on my K3.
Not an interaction, but unexpe
I second the motion.
73, Carl WS7L
> I don't know if anyone has requested it yet, but how about a
> pulse tuning function for those of us who use tube amps?
>
> 73 and Merry Christmas to all!
>
> James K2QI
__
Elecraft mailing list
I don't know if anyone has requested it yet, but how about a pulse tuning
function for those of us who use tube amps?
73 and Merry Christmas to all!
James K2QI
On Wed, Dec 23, 2009 at 1:02 PM, Wayne Burdick wrote:
> Hi all,
>
> As you probably know, we keep a list of firmware features and
> im
I'd like to see the following enhancement:
Currently the transverter offset can be adjusted +/-9.99 kHz. I'd like
to have this range extended - maybe to +/- 99kHz.
Having an XV432 with stock XTAL + oven, the elevated temperature from
the oven pushes the LO quite a bit in frequency. I know that on
Brian,
Concentrate on the labels below the buttons - V>M is RECord while M>V is
PLAY - that helps keep my head 'screwed on right'.
You may get the lockout sometime, but that is not now.
73,
Don W3FPR
Brian Machesney wrote:
> I would like to be able to "lock" the "V->M" front panel key.
>
> In w
> In what must surely be the latest evidence of my brain's
> declining function,
> I constantly confound the "V->M" and "M->V" buttons,
> inadvertently writing
> over the memory contents. Pressing the "V->M" button while it
> is "locked"
> would produce an audible beep and the text message "unlo
I would like to be able to "lock" the "V->M" front panel key.
In what must surely be the latest evidence of my brain's declining function,
I constantly confound the "V->M" and "M->V" buttons, inadvertently writing
over the memory contents. Pressing the "V->M" button while it is "locked"
would prod
ginal Message -
From: "Barry N1EU"
To:
Sent: Thursday, December 24, 2009 7:30 AM
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
>
>
> N2TK wrote:
>>
>> Is there any way to setup the K3 utility through LP-Bridge to send macros
>> fo
Good thing that reflector not the prime sales media. I would assign
that to word of mouth and Elecraft repeat customers. You got one
contester telling another that he hears things with his K3 that never
heard (or never heard well enough to copy) before, and it gets around
that a multi/op owner li
I have to admit that reading these posts has been interesting, if not down
right exhausting.
Some good suggestions, some pretty narrowly focused and esoteric ones, some
related more to the (at best) barely coherent jumble of PC software sitting
behind the radio than the radio itself, and so
1) A mode specific BAND switch (i.e., CW, SSB, AM, etc would each have
ten dedicated bands avaialble, independent of the other modes)
2) A "live" PITCH control so you can hear the pitch of received
signals as you adjust it, not covered by sidetone.
3) A "smart" passband shift step: 10 Hz for narr
Strongly seconded David! I would just add for the avoidance of doubt that
MON should go back to 0 again when the txing from DVR memory has finished.
Otherwise it would be possible with a macro.
73 and Happy Christmas to all
Geoff
G3UCK
- Original Message -
From: "David Pratt"
>I do
I would like to see the K3 have advanced serial command set that would allow
the programmer to send the commands with an ID that would be returned when
the K3 responds. That would allow Larry to modify LP Bridge so that it
could route the appropriate response to the appropriate sender without
hav
wayne burdick wrote:
>
> As we head into 2010, we'd like to refresh the master firmware list
> based on your input. Items already on the list have priority, of
> course, but this is a great opportunity to let us know what else is
> missing or could be improved. Our goal is to make the K3 a
For us microwavers, who find the K3 to be the best microwave IF rig, the
ability to lock the K3 to a 10 MHz reference is very important. Microwave
receiver bandwidths are getting smaller and an insignificant frequency error
at HF results in an error of hundreds of kilohertz if not megahertz at
1. Fix it so spot pitch does not mute the RX. Makes it hard to
adjustin a busy contest. At a multi, different CW ops have different
tone centers. Folks at NY4A set it anywhere from 450 to 650. Comes
into play when handing off a run to another op for a bathroom break.
Hit CQ, hand the headsets and
"Barry N1EU"
To:
Sent: Thursday, December 24, 2009 7:30 AM
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
>
>
> N2TK wrote:
>>
>> Is there any way to setup the K3 utility through LP-Bridge to send macros
>> for the utili
N2TK wrote:
>
> Is there any way to setup the K3 utility through LP-Bridge to send macros
> for the utility program to the K3 without having to close LP-Bridge then
> starting the K3 utility program? I understand that you have to close the
> LP-Bridge for downloading updates.
>
Why don't you j
- Original Message
From: Dick Dievendorff
Barry asked for the ability to display AGC parameters. These values are
currently read by accessing menus and reading them from the VFO A display
area. During that menu access, another application might send an UP or DN
command, which could
Hi
We talking firmware only?
Better S-meter resolution maybe a Dbm or Db microvolt scale for field strength
measurements
S-meter peak memories - calculates difference for antenna comparisons
Averaging S-meter readings with sampling time setting
Transmit Double sideband suppressed carrier
I
The ability to transmit AM thru the FM crystal filter.
73
Stewart G3RXQ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This lis
This is what I like to see:
1. Pritty much no more features just refine and work
on what´s already there, refine the design.
2. Better S-meter resolution, 5 dB not good enough.
3. Possibility to adjust CW keyed envelope rise and
fall time. Think it´s 5 ms now so lets say 5 - 8 ms
adj
I do not use headphones and therefore have the monitor at zero so as not
to cause feedback, but it would be nice to hear what's going on when
sending from the DVR. Could the MON be set to a pre-set level when
transmitting from the DVR memory?
(Not sure whether that is included in the following,
Pretty pleased with the way my K3 works. The only improvements
which come immediately to mind concern the memories.
1) The ability to create, edit and store all K3 memory parameters
on a computer and then upload them to my K3.
2) Some form of memory protection to prevent accidental
overwriting
the
winner improvement ideas and start a new list.
Gary, VE1RGB
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Lee Buller
Sent: December 23, 2009 11:59 PM
To: Elecraft Reflector
Subject: Re: [Elecraft] K3 needs survey
ailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick
Sent: Wednesday, December 23, 2009 12:02 PM
To: Elecraft Reflector; elecr...@yahoogroups.com;
elecraft...@yahoogroups.com
Subject: [Elecraft] K3 needs survey -- firmware and application software
Hi all,
As you probably know, we keep
: Elecraft Reflector; elecr...@yahoogroups.com;
elecraft...@yahoogroups.com
Subject: [Elecraft] K3 needs survey -- firmware and application software
Hi all,
As you probably know, we keep a list of firmware features and
improvements to be added as time permits. Many of the most-requested
changes were
: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of AD6XY
Sent: Wednesday, December 23, 2009 5:44 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
There is a lot here about the K3 firmware tweaks - so
.qth.net
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
Dick,
LP-Bridge acts as a traffic cop that allows multiple programs to share the
K3 COM port without interfering with each other. It opens the K3 COM port
and sends various commands to obtain a continous flow of co
Boythe dam and broke Spent the lats 45 minutes reading all this stuff.
Here is my very short list.
1. Power control - Fine and Course To many turns to get to the power I want.
Especially driving an amp. I think that others have talked about power control
with amplifiers. In my s
Application software - I have a KRC2 and I would like it to know the
difference between 6m and 10m. In fact it would be nice to get away from the
fixed bands per relay and instead map bands and potentially sub-bands to
relays via the utility. The new KRC2 firmware can apparently manage this but
un
:02 PM
>> To: Elecraft Reflector; elecr...@yahoogroups.com;
> elecraft...@yahoogroups.com
>> Subject: [Elecraft] K3 needs survey -- firmware and application software
>>
>> Hi all,
>>
>> As you probably know, we keep a list of firmware features and
>> improvem
On Wed, Dec 23, 2009 at 9:23 PM, Jim Miller wrote:
> As another mentioned, a digital signal out when the ATU is uninstalled or
> disabled and Tune is tapped to allow activation of an external tuner would
> be very nice to have. I use a remote tuner (T1) at my antenna base and the
> internal tuner
As another mentioned, a digital signal out when the ATU is uninstalled or
disabled and Tune is tapped to allow activation of an external tuner would
be very nice to have. I use a remote tuner (T1) at my antenna base and the
internal tuner in the K3 as well at times.
73
jim ab3cv
_
Here are some answers to some of the questions posed about LP-Bridge
behavior...
1. LPB responds to all application "GET" commands from memory, without
passing the commands to the K3. This happens asynchronously from up to five
applications at the same time. Each application only sees responses t
1. NTCH within AGC
2. Manual NTCH narrower (like in IC-7000)
3. DUAL PB with adjustable Q so that it works closer to audio filters
(current Q mostly too low).
--
View this message in context:
http://n2.nabble.com/K3-needs-survey-firmware-and-application-software-tp4209832p4211530.html
Sent fr
t-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Phil &
> Debbie Salas
> Sent: Wednesday, December 23, 2009 5:24 PM
> To: elecraft@mailman.qth.net
> Subject: Re: [Elecraft] K3 needs survey -- firmware and
> application software
>
>
> F
rate, and that's not always
> > possible.
> >
> > Dick
> >
> >
> > -Original Message-
> > From: Dick Green WC1M [mailto:wc1...@gmail.com]
> > Sent: Wednesday, December 23, 2009 2:31 PM
> > To: 'Dick Dievendorff'; '
ilto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick
> Sent: Wednesday, December 23, 2009 1:02 PM
> To: Elecraft Reflector; elecr...@yahoogroups.com;
> elecraft...@yahoogroups.com
> Subject: [Elecraft] K3 needs survey -- firmware and
> application software
>
&g
t;
>
> -Original Message-
> From: Julian Moss [mailto:julian.g4...@gmail.com]
> Sent: Wednesday, December 23, 2009 3:40 PM
> To: Dick Dievendorff
> Cc: Wayne Burdick; wc1...@gmail.com; elecraft@mailman.qth.net
> Subject: Re: [Elecraft] K3 needs survey -- firmwar
k
Subject: [Elecraft] K3 needs survey -- firmware and application software
To: "Elecraft Reflector" , elecr...@yahoogroups.com,
elecraft...@yahoogroups.com
Date: Wednesday, December 23, 2009, 11:02 AM
Hi all,
As you probably know, we keep a list of firmware features and
improvements
Original Message-
> From: Julian Moss [mailto:julian.g4...@gmail.com]
> Sent: Wednesday, December 23, 2009 7:08 PM
> To: Dick Dievendorff
> Cc: Wayne Burdick; wc1...@gmail.com; elecraft@mailman.qth.net
> Subject: Re: [Elecraft] K3 needs survey -- firmware and application
software
Yes. I don't know why he asked for that. Perhaps he would care to say
why it would be useful? I don't think that many people would want that
information on display in real time so I wouldn't expect that
developers would rush to provide a display that showed AGC parameters
anyway.
Applications shou
.qth.net
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
Perhaps the solution is to make it possible to obtain information
about the state of things that an operator might want to change
without having to open a menu?
Barry asked for some specific information to be d
Perhaps the solution is to make it possible to obtain information
about the state of things that an operator might want to change
without having to open a menu?
Barry asked for some specific information to be displayed on-screen.
He was not even requesting the ability to change those items from th
: Wayne Burdick [mailto:n...@elecraft.com]
Sent: Wednesday, December 23, 2009 3:21 PM
To: Dick Dievendorff
Cc: ; Julian, G4ILO;
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
I don't think all such cases can handled in reality. Programs doing
menu manipulation sho
Wednesday, December 23, 2009 2:31 PM
> To: 'Dick Dievendorff'; 'Julian, G4ILO'; elecraft@mailman.qth.net
> Subject: RE: [Elecraft] K3 needs survey -- firmware and application
> software
>
> Dick,
>
> LP-Bridge acts as a traffic cop that allows multiple program
t status when
it's needed.
73, Dick WC1M
> -Original Message-
> From: Dick Dievendorff [mailto:die...@comcast.net]
> Sent: Wednesday, December 23, 2009 5:38 PM
> To: wc1...@gmail.com; 'Julian, G4ILO'; elecraft@mailman.qth.net
> Subject: RE: [Elecraft] K3 n
There is a lot here about the K3 firmware tweaks - so I will address the
other sides of Wayne's question.
Application software - I have a KRC2 and I would like it to know the
difference between 6m and 10m. In fact it would be nice to get away from the
fixed bands per relay and instead map bands
1. Restore the full range of SHIFT while in 10 Hz resolution
(currently limited to 1.28 to 1.72 kHz) to match the range while set
to 50 Hz steps (0.05 to 2.60 kHz).
2. Increase power output to around 800W by means of some sort of
external add-on device. :-)
Merry Christmas!
Paul WW2PT
On
WC1M
> -Original Message-
> From: Wayne Burdick [mailto:n...@elecraft.com]
> Sent: Wednesday, December 23, 2009 1:02 PM
> To: Elecraft Reflector; elecr...@yahoogroups.com;
elecraft...@yahoogroups.com
> Subject: [Elecraft] K3 needs survey -- firmware and application software
>
73, Dick WC1M
> -Original Message-
> From: Dick Dievendorff [mailto:die...@comcast.net]
> Sent: Wednesday, December 23, 2009 3:35 PM
> To: 'Julian, G4ILO'; elecraft@mailman.qth.net
> Subject: Re: [Elecraft] K3 needs survey -- firmware and application
software
>
>
to:die...@comcast.net]
> Sent: Wednesday, December 23, 2009 3:35 PM
> To: 'Julian, G4ILO'; elecraft@mailman.qth.net
> Subject: Re: [Elecraft] K3 needs survey -- firmware and application
software
>
> Would the loggers object to receiving responses to commands that they
For external amplifier and external high power auto-tuner use, I'd like to
see the followiong:
1) External ground that automatically puts the K3 into a low power CW tune
mode. This is normally a command from an external auto-tuner that comes
after an amplifier.
2) When the low power tune mo
I would love to see separate volume adjustments for Spot and Sidetone.
Happy Holidays to all!
73, Gary W7TEA
-
73,
Gary W7TEA K3 #1001
--
View this message in context:
http://n2.nabble.com/K3-needs-survey-firmware-and-application-software-tp4209832p4210728.html
Sent from the Elecraf
I'e been using the same (now old) homebrew Accu-keyer with auto character
spacing since the articles were originally published in QST. I'm so used to
the timing, it's hard to send decent CW otherwise. Except with a Lightning
Bug, although some may not consider the swing "decent" :-)
It would
Wayne,
I updated my list of bugs and suggested changes Please give me your email.
Pse reply to h...@trx-manager.com
Best regards, Laurent F6DEX
http://trx-manager.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/li
- Main and Sub Rx audiomix:
Leftchannel -> 100% main and 50% sub and
Rightchannel -> 100% sub and 50% main
- Bring Notch filter inside AGC-loop (or partly inside)
- P3 point and click to change freq with a usb-MOUSE
Thanks
73
Arie PA3A
__
Yes!
I don't use the K3 internal keyer for exactly that reason.
Bryan, Zl1NI
> ..
> The K3 built-in keyer is very good as it is, but I miss the
> automatic
> character spacing of my favorite external keyers (CMOS Super Keyer,
> Logikeyers, Accukeyers, etc.)
As previously reported:
1. Eliminate power transients when transmitting FSK-D.
2. Raise threshold on AF Limiter to prevent gross distortion when
receiving CW with AGC OFF.
Thanks for listening, and Merry Christmas to all!
Dave Hachadorian, K6LL
Yuma, AZ
.
___
craft@mailman.qth.net
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
Dick Dievendorff wrote:
>
> Would you dedicate the K3's serial port to this function? Instead of a
> contest logger?
>
Why would you need to, given LP-PAN, VSPE etc?
-
Julian, G
Dick Dievendorff wrote:
>
> Would you dedicate the K3's serial port to this function? Instead of a
> contest logger?
>
Why would you need to, given LP-PAN, VSPE etc?
-
Julian, G4ILO. K2 #392 K3 #222.
* G4ILO's Shack - http://www.g4ilo.com
* KComm - http://www.g4ilo.com/kcomm.html
* KTu
N1EU; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
Outstanding suggestion. I would second this one. Even better if we
could change the settings
73, Tom W2SC 8P5A
-Original Message-
From: Barry N1EU [mailto:barry.n...@gmail.com]
survey -- firmware and application
software
To address the limited display area of the K3, I'd like to see a simple
pc
application that will present a virtual K3 display on the computer
screen
and provide full-time display of:
shift (numeric)
width (numeric)
power
compression
mic gain
sub pream
Both the KX1 and the K3 announcements were real surprises to me. They
certainly were well-kept secrets.
The K3 built-in keyer is very good as it is, but I miss the automatic
character spacing of my favorite external keyers (CMOS Super Keyer,
Logikeyers, Accukeyers, etc.). As a CW operator, I wou
In my short time ( 2 weeks ) with this wonderful radio I have had several
"wow, look at this!" moments on most days.
The one feature that I have come to wish for, so far, is the ability to have
two or three TX Equalizer set ups and the ability to make comparisons by
switching quickly from a se
ons Greetings to all
73, Doug VE3MV
K3/100 s/n 2432
- Original Message -
From: "Wayne Burdick"
To: "Elecraft Reflector" ;
;
Sent: Wednesday, December 23, 2009 1:02 PM
Subject: [Elecraft] K3 needs
To keep it as brief as possible:
-RX EQ per mode, so every mode can be tailored (and we will never get into
"noise threads" again :-)
-European 144/430 FM step raster support 6.25 and 12.5 kHz (With the K144XV
in mind)
-Memory editor utility and 50(?) more memories (also with the K144XV in
mind)
2009 11:41 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 needs survey -- firmware and application software
Wayne,
Even though I am a brand new K3 owner (received last week), we really need a
software program to manage memories. Need to read and write to the K3, freq,
mode, off
To address the limited display area of the K3, I'd like to see a simple pc
application that will present a virtual K3 display on the computer screen
and provide full-time display of:
shift (numeric)
width (numeric)
power
compression
mic gain
sub preamp
sub antenna selection
sub shift
sub width
AF
SWR Meter Peak Hold on SSB
Improved SWR Accuracy
73,
Dick - KA5KKT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list h
Any chance we could see the list? Simply choosing those that are high
on our list might help to firm up the various items.
On Wed, Dec 23, 2009 at 1:02 PM, Wayne Burdick wrote:
> Hi all,
>
> As you probably know, we keep a list of firmware features and
> improvements to be added as time permits.
the way it is now. 73
Steve
N4LQ
n...@carolina.rr.com
- Original Message -
From: "Wayne Burdick"
To: "Elecraft Reflector" ;
;
Sent: Wednesday, December 23, 2009 1:02 PM
Subject: [Elecraft] K3 needs survey -- firmware and application software
> Hi all,
>
>
Wayne,
Even though I am a brand new K3 owner (received last week), we really need a
software program to manage memories. Need to read and write to the K3, freq,
mode, offset for fm repeater work
This is really basic to radios I have had for over 5 years….anyway, hope
this makes the priority list
Hi Wayne and Elecraft team,
First of all a bit thank you for the fun I had with the K3 over the last
year, including all the software changes and the involvement of all of us in
the new developments of the K3. I must say this is outstanding and what
puts Elecraft on a different level than any ot
I would love to see 3 things...
1) Receive EQ by mode
2) Monitor on the KDVR to not be in the TX chain
3) Decent Memory management
Anything else is a bonus but those are my wishes for 2010 :)
Seasons greetings to all the gang at Aptos!
73 Ian
--
Ian J Maude, G0VGS
SysOp GB7MBC & HB9DRV-9 DX C
A command to get decoded CW, PSK31 and RTTY text into a computer program
while CAT is enabled (in other words, something better than TT1.)
Support for upper and lower case when sending PSK31 using the internal modem
and computer generated text.
Per-mode equalization.
A discriminator meter for n
I'm a heavy user of diversity (99.9% of the time). I have many different RX
antennas which have differing amounts of gain. For diversity to work
correctly, I need both antennas to present the same RF levels to both
receivers. I can make gross adjustments with ATT/PRE, but for fine tuning I
woul
How about a webpage listing the features(non-prioritized from your
standpoint)? With the ability to add to it, and maybe vote on the requests?
I love surprises(wlll mostly).
73, Mike NF4L
Wayne Burdick wrote:
> Hi all,
>
> As you probably know, we keep a list of firmware features and
Hi all,
As you probably know, we keep a list of firmware features and
improvements to be added as time permits. Many of the most-requested
changes were made over the past several months, keeping pace with the
demands of the fall/winter contest season. (A few that come to mind:
switch seque
100 matches
Mail list logo
