[AFMUG] Tales from the Towers - Chapter 64 posted

http://muniwireless.com/2018/01/09/tales-towers-chapter-64-migrate-migraine/ Rory Conaway * Triad Wireless * CEO 4226 S. 37th Street * Phoenix * AZ 85040 602-426-0542 r...@triadwireless.net www.triadwireless.net "Yesterdays Home Runs

Re: [AFMUG] RackInjector + ePMP 2k

No, this is just my bench setup for now. So no surge suppressors, bonding and stuff to make things more confusing. Honestly, I've just been using the on-board GPS on the ePMP stuff until now, mostly because we've been doing omni micro-POP sites or one or two sectors. But we're going to start

Re: [AFMUG] Employee clocking out and such...

Our guys clock out when they get back. They don't clock in until they get to the office or if leaveing straight to a job they can clock in right away. But if I send the an hour away from home/the office to do an install. I feel like it's only fair to pay them to drive home. Now obviously if home

Re: [AFMUG] RackInjector + ePMP 2k

i have a set not syncing off the powerinjector, im thinking its that all the radio grounds ar bonded top and bottom and the pipe is also, so is an equal ground plane with too long a run, its freaking it out some how, havent gone to unbond the tops yet im assuming the guts are essentially the same

Re: [AFMUG] Employee clocking out and such...

They clock out when they leave their last job. We don't pay for the first 30 minutes of their commute to/from their first and last job. So if they go to their first job in the morning 45 minutes away, we pay for 15 minutes. If their last job is 45 minutes from home, we again only pay for 15

[AFMUG] RackInjector + ePMP 2k

So, the ePMP 2k ships with a passive POE brick that's +4/5 -7/8, 48VDC. That's how I have the port on the RackInjector jumpered. Radio is set to sync source = CMM3. Status shows CMM Sync Down. Now the obvious question is, I'm guessing I needs it to be -4/5 +7/8 like traditional Canopy? The 2k

Re: [AFMUG] pissed at rohn

isnt rohn made in peoria? you want that plant should have some storm damage or some embers of that California fire should happen to land on their roof? sometimes these things, manufacturing joints, they aint so wired up good, you know, sometimes the plants burn down On Tue, Jan 9, 2018 at 2:14

[AFMUG] Employee clocking out and such...

For employees with company install vehicle, at what point is everyone having them clock out at the end of the day if they are allowed to take it home? When the job is done? Or when they ‘get back’? What about gas usage if they take it home? Thanks Jon Langeler Michwave Technologies, Inc.

Re: [AFMUG] Cambium PTP650 question

Ok.. I got to bottom of clients questions...he needs two PTP-NIDU's indoor units. Anyone on list sell them ?get me off list...Thanks, Jaime Jaime Solorza On Jan 9, 2018 4:09 PM, "Dave" wrote: > I know that with ptp650 I think you can set the link to be configured for >

Re: [AFMUG] Cambium PTP650 question

I know that with ptp650 I think you can set the link to be configured for tdm traffic. Nothing special other than that. On 01/09/2018 03:47 PM, Jaime Solorza wrote: Have any of you Kool Kats used these to connect T-1 Phone Systems together?  Have a 5GHz PTP link using Flanger Memory links

[AFMUG] Cambium PTP650 question

Have any of you Kool Kats used these to connect T-1 Phone Systems together? Have a 5GHz PTP link using Flanger Memory links to convert T-1 to Ethernet to connect two phone systems together. Has worked well for 8 years... Jaime Solorza

Re: [AFMUG] pissed at rohn

Ahh, but THIS tower is facing EAST. WHOOOEEE Separate drawing haha, good luck Thank you, Ben Royer, Operations Manager Royell Communications, Inc. 217-965-3699 www.royell.net From: Chuck McCown Sent: Tuesday, January 09, 2018 2:14 PM To: af@afmug.com Subject: Re: [AFMUG] pissed

Re: [AFMUG] pissed at rohn

Happy to have any help with this. From: Craig House Sent: Tuesday, January 09, 2018 1:05 PM To: af@afmug.com Subject: Re: [AFMUG] pissed at rohn Chuck let me make a call I’ve got a local rohn guy Sent from my iPhone On Jan 9, 2018, at 13:44, Chuck McCown wrote:

Re: [AFMUG] pissed at rohn

No, they are just saying I don’t have the option of not buying the drawings for subsequent towers. No matter what I am going to have to buy the drawings. If they had that kind of thing going, they should have not itemized the original quote. From: Adam Moffett Sent: Tuesday, January 09,

Re: [AFMUG] pissed at rohn

Thanks. This is for a site in Louisianan. From: Craig House Sent: Tuesday, January 09, 2018 1:05 PM To: af@afmug.com Subject: Re: [AFMUG] pissed at rohn Chuck let me make a call I’ve got a local rohn guy Sent from my iPhone On Jan 9, 2018, at 13:44, Chuck McCown wrote:

Re: [AFMUG] Reel payoff equipment

Hah ok, yeah non-issue then. -- Original Message -- From: "Chuck McCown" To: af@afmug.com Sent: 1/9/2018 3:00:07 PM Subject: Re: [AFMUG] Reel payoff equipment Maybe 36” for drop, depending on the type of drop. From:Adam Moffett Sent: Tuesday, January 09, 2018 12:58

Re: [AFMUG] pissed at rohn

Chuck let me make a call I’ve got a local rohn guy Sent from my iPhone > On Jan 9, 2018, at 13:44, Chuck McCown wrote: > > Bought a 100’ SSV tower. > Want a second one just like it. > They want $1000 more for the tower. Bottom line is the same but they quoted > about $4150

Re: [AFMUG] pissed at rohn

Has the price of steel gone up recently? Trylon Super Titan is the first alternative that comes to mind. Tessco sells the kits. The cheapest ones are very light duty, so look at their load charts. -- Original Message -- From: "Chuck McCown" To: af@afmug.com

Re: [AFMUG] Reel payoff equipment

Maybe 36” for drop, depending on the type of drop. From: Adam Moffett Sent: Tuesday, January 09, 2018 12:58 PM To: af@afmug.com Subject: Re: [AFMUG] Reel payoff equipment On second pass, I was probably picturing a 40,000 foot reel being bigger than it really is. -- Original Message

Re: [AFMUG] Reel payoff equipment

On second pass, I was probably picturing a 40,000 foot reel being bigger than it really is. -- Original Message -- From: "Chuck McCown" To: af@afmug.com Sent: 1/9/2018 2:08:40 PM Subject: Re: [AFMUG] Reel payoff equipment Yes, just pull it off at the job site. Or if

[AFMUG] pissed at rohn

Bought a 100’ SSV tower. Want a second one just like it. They want $1000 more for the tower. Bottom line is the same but they quoted about $4150 for the tower on the first quote and are quoting $5150 for the second. First tower came with $1000 for drawings. I already have the drawings. I

Re: [AFMUG] Reel payoff equipment

Yes, just pull it off at the job site. Or if you have a good idea on lengths, make hand coils. From: Adam Moffett Sent: Tuesday, January 09, 2018 12:04 PM To: af@afmug.com Subject: Re: [AFMUG] Reel payoff equipment Do you just spin the reel by hand to spool out what you need? --

Re: [AFMUG] Reel payoff equipment

I've got a hydraulic reel trailer, but I've found that it is just as easy to cut the drops ahead of time, roll them up, and load them into the van. This is also nice, since I splice both ends of the drop, I can go ahead and splice the drop fiber into the enclosure that goes on the house ahead of

Re: [AFMUG] Reel payoff equipment

Do you just spin the reel by hand to spool out what you need? -- Original Message -- From: "Chuck McCown" To: af@afmug.com Sent: 1/9/2018 1:41:37 PM Subject: Re: [AFMUG] Reel payoff equipment We just use the large reel. Get a reel holder that you can pull behind a

Re: [AFMUG] OT I would like to be the first to say.....

Even I was pretty impressed with Tu... I really don't want much football if the game is not projected to be really good. Therefore, I haven't really seen him play prior to this game. When he came in, I was pretty shocked at what he was able to do. - Original Message - From: Jay

Re: [AFMUG] OT I would like to be the first to say.....

There are a lot of Alabama fans in the ICU today. Rick Harnish wrote: They ALMOST Rolled Over. Respectfully, -- Rick Harnish Director of WISP Markets Baicells Technologies North America, Inc. Mobile: (972) 922-1443 rick.harn...@baicells.com www.facebook.com/baicells

Re: [AFMUG] Reel payoff equipment

We just use the large reel. Get a reel holder that you can pull behind a vehicle. From: Adam Moffett Sent: Tuesday, January 09, 2018 10:50 AM To: af@afmug.com Subject: [AFMUG] Reel payoff equipment As I'm getting into larger quantities of fiber, I'm finding that I will get the best

[AFMUG] Reel payoff equipment

As I'm getting into larger quantities of fiber, I'm finding that I will get the best pricing on 40,000 ft reels of drop cable. If we do that, then I'll need some kind of payoff system to transfer cable onto smaller spools for field techs. I have no idea where to begin shopping for that, but

Re: [AFMUG] Gino in the news

Lots of good places to eat in Galveston..have fun... Jaime Solorza On Jan 9, 2018 10:17 AM, "Gino A. Villarini" wrote: > Heading down to Galveston, then a Cruise home… > > From: Af on behalf of Jaime Solorza < > losguyswirel...@gmail.com> > Reply-To:

Re: [AFMUG] Gino in the news

Heading down to Galveston, then a Cruise home… From: Af > on behalf of Jaime Solorza > Reply-To: "af@afmug.com" > Date: Tuesday,

Re: [AFMUG] Gino in the news

That's like LA distance for me Luther's Barbeque is good and most Vietnamese restaurants as well in most of Houston area Jaime Solorza On Jan 9, 2018 9:13 AM, "Gino A. Villarini" wrote: > Hola desde Houston.. > > From: Af on behalf of Jaime

Re: [AFMUG] Gino in the news

Hola desde Houston.. From: Af > on behalf of Jaime Solorza > Reply-To: "af@afmug.com" > Date: Tuesday, January 9, 2018 at 11:33 AM

Re: [AFMUG] Gino in the news

Yeah, I am very anxious to hear his unvarnished opinion of the radios and the band after he has had them up for 6 months. Gino is one guy I trust to give us the straight story. From: Jaime Solorza Sent: Tuesday, January 09, 2018 8:33 AM To: Animal Farm Subject: [AFMUG] Gino in the news We

Re: [AFMUG] Gino in the news

On Tue January 9 2018 09:33, Jaime Solorza wrote: > We have a celebrity amongst us Gino's company featured in Siklu press > releaseway to Gino!!! Saludos. > > Jaime Solorza +10 Gino -- Larry Smith lesm...@ecsis.net

[AFMUG] Gino in the news

We have a celebrity amongst us Gino's company featured in Siklu press releaseway to Gino!!! Saludos. Jaime Solorza

Re: [AFMUG] OT I would like to be the first to say.....

They ALMOST Rolled Over. Respectfully, -- Rick Harnish Director of WISP Markets Baicells Technologies North America, Inc. Mobile: (972) 922-1443 rick.harn...@baicells.com www.facebook.com/baicells -Original Message- From: Af [mailto:af-boun...@afmug.com] On Behalf