microphone input (front or rear).
73,
Mike K2MK
Bud Governale, W3LL wrote
When I hit a function key in N1MM the correct wav file plays as heard thru
the computer speakers.
However the K3 (in SSB mode) does not transmit.
Any suggestions?
73,
Bud W3LL
--
View this message in context
it in both fixed-tune
mode and tracking mode. It is infrequent and totally random.
73,
Mike K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/P3-time-required-to-stabilize-after-transmit-tp7595748.html
Sent from the Elecraft mailing list archive at Nabble.com
or operating styles.
It is so good that you will want to add a 2nd monitor to your PC for it's
sole use.
73,
Mike K2MK
Dauer, Edward wrote
I have resisted using spotting systems until now, preferring to hunt on my
own. Somehow, being primordial seemed more authentic. But as the totals
rise
for that situation.
73,
Mike K2MK
wayne burdick wrote
Vic Rosenthal lt;
k2vco.vic@
gt; wrote:
Turning down either the audio or RF gain helps with both artifacts, but
makes the output lower than desirable.
I talked to Wayne and Lyle a long time ago about possible ways to
ameliorate these noises
meter are solidly lit with the 5th bar flickering.
73,
Mike K2MK
SouthCarolinaDolphin wrote
A friend is using my K3 while his is in the shop When he transmit's on the
K-3 running a specific power out he notices that the power especially on
RTTY will start at a lower output that what
add a computer into the mix. Do you want to risk damaging the expensive
SteppIR EHU or do you want to spend some money for protection.
73,
Mike K2MK
Elecraft mailing list wrote
GM/GA/GE,
The K3 question in connection with Steppir yagi(s).
Will Steppir yagi follow K3 in the same manner
that might affect this suggestion. Such as whether you
are using the front or rear headphone jack and whether you have external
speakers plugged in to the rear jack.
73,
Mike K2MK
Jeff Maass wrote
We have a new-to-us K3 at the PJ2T station (#00157). It has had some
upgrades done
Hi Fred,
Yes the Elecraft Key line interrupter and either the SteppIR built-in tuning
relay or the N8LP external tuning relay are critically needed with any
SteppIR antenna.
73,
Mike K2MK
Cady, Fred wrote
I don't have a stepper but you might need to have a key line interrupter
so you don't
Hi Tex,
Almost. One leg of the Y cable is very short so you'll need a serial
extension cable. There's a good drawing from SteppIR that shows how the Y
cable connects to the multiple devices. Not specifically the K3 but any
transceiver. E-mail me directly if you need a copy. k2mk at comcast dot
you want to see MAIN on the lower display and not AUX.
73,
Mike K2MK
mike wrote
Sub receiver all of sudden does not produce signal. Audio is not dead, but
cannot hear the VFO B signal in split operation. Where should I start to
find what has gone wrong? ..mike
--
View this message
to see a data sheet. The diameter is 6.35mm and the
length is 31.75mm.
http://www.mouser.com/ProductDetail/Littelfuse/0312006HXP/?qs=sGAEpiMZZMsIz3CjQ1xegWrlMY7vL59hjcmRNw8S59U%3d
73,
Mike K2MK
Ken Chandler wrote
I was in the WAE rtty contest today when I heard a pop fizz, Red fault
lamp
WriteLog that cause actions to occur on both my K3
and P3. One macro uses the F12 button and the other macro uses the * button
on the numeric keypad.
73,
Mike K2MK
***
[Elecraft] [K3] Programmable/assignable Split Key?
Jim Miller Wed, 05 Nov 2014 15:40
for your SUB RX on
15 meters and if you don't have anything connected to those inputs then you
would indeed hear no audio on your right channel speaker when on 15 meters.
73,
Mike K2MK
KD3TB wrote
With the K3 in Split mode and Sub turned on, on 20 Meters I can hear the
Main and sub band
,
Mike K2MK
mike wrote
When using KPA500 my external monitor (and the P3 display) often freezes,
sometimes up to 5 seconds, after I transmit. With the external display
disabled, the P3 does not freeze (and incidentally it refreshes much
faster without the ext monitor enabled.) I also notice
/order_form_parts.htm#K3%20Parts
73,
Mike K2MK
Darryl J Kelly wrote
Any problems with buying a K3 with a low serial number, say that has
had hardware updates and alignments?
Darryl, KK5IB
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Low-Serial-Numbered-K3
of time. I suppose
some aging occurs and of course power is consumed.
73,
Mike K2MK
Phil Hystad-3 wrote
I have two questions (slightly related) about the KPA500.
Question 1: Assuming that there is no transmitted signal at all, is there
any difference in whether a KPA500 is switched into OPER
.
Remember also that the DSP upgrade is considered an enhancement and
therefore might not be listed along with all of the other hardware
modifications.
73,
Mike K2MK
Mike Reublin wrote
Trevor -
The Elecraft website lists the mods at
http://www.elecraft.com/K3/k3_app_notes.htm
73, Mike NF4L
Hi Andrew,
Are you able to key your amplifier when operating normally? There's really
no difference with the Tune button. It should key the amplifier the same
way. Remember that tune is achieved by holding the XMIT button.
73,
Mike K2MK
Andrew UK wrote
Hi,
I have noticed that when I hit
Hi Tim,
If you have a SUB RX and it is activated the sidetone comes through on the
left channel. Sidetone is independent of volume settings, however, if you
have somehow totally disabled your left channel you won't hear the sidetone.
73,
Mike K2MK
KQ8M wrote
I hope someone can help. I am
coast
time on Monday.
What an excellent organization.
73,
Mike K2MK
Dave Jones wrote
And mine too. :-(
Dave Jones
VK4FD
zendoc@.net
wrote on 08/18/2014 07:21 AM:
My VFO B knob cracked within 6 months of assembly. It was replaced
immediately under warranty and no problems since
Hi Knut,
The sudden response to your post prompted me to take out the flashlight.
Mine has a hairline crack from the setscrew back towards the front panel.
The crack is not present from the setscrew to the face of the knob. My unit
is S/N 22xx from 2008.
73,
Mike K2MK
ab2tc wrote
Hi all
.
It looks like Elecraft did a fine job controlling temperature for heavy RTTY
operation. I would not hesitate to recommend the KPA500 for RTTY contesting
but I would certainly want to mention that the occassional higher fan speeds
might annoy some operators.
73,
Mike K2MK
--
View this message
Hi Keith,
I might be interested but I didn't bother downloading the firmware because I
never look at the P3 screen, only the SVGA screen. How well does it work and
weren't there some caveats mentioned in the release notes?
73,
Mike K2MK
XE3/K5ENS wrote
I must be the only one that has bought
Hi John,
Thanks for posting the audio link. As you said on your blog, it is far more
interesting then reading the written text. I think I'll listen to it again.
73,
Mike K2MK
John Harper AE5X wrote
For those who didn't hear it via their local FM station, here is the
audio:
http
to an Fn key and
then pushing the button twice.
73,
Mike K2MK
Jim AB3CV wrote
I'd like to assign the Center function (Span hold) to a function key but
haven't figured out how to do this. The only menu entry for Center is for
disabling it under tracking mode (no idea why that would be useful
know what
you're looking for.
73,
Mike K2MK
George Thornton wrote
I have a k3 that was working fine but now will not power up.
I had lent the unit to someone to use at Field Day. They reported it
would not power up.
Going through the unit it appears that a nut and washer has come off
Hi Bill,
Not mysterious. If I knew I would have said. But luckily Don knows what to
look for and responded.
73,
Mike K2MK
Bill W2BLC wrote
if you know what you are looking for.
H, given any thought to explaining that mysterious statement? Not
everyone knows what you
Hi Reggie,
This device could start you off in the right direction. I have no personal
experience with it.
http://www.qth.com/topten/abss.htm
73,
Mike K2MK
Reggie wrote
I have the K3 and and Flex 6500, and I would like to hook both
transceivers to the KPA500 and the KAT500
monitor. I call
this the code practice mode.
73,
Mike K2MK
ac2ev wrote
I tried using a keyboard and the P3 in data mode to send CW but it
wouldn't put the K3 in transmit. I could receive and decode CW. When I
tried to transmit a memory location or via typing I could hear the CW it
was trying
it
says ON. Then adjust the threshold accordingly with the VFO A dial. My
threshold is on 3.
And finally, if you are decoding RTTY make sure your DATA MD is AFSK A at 45
bps (not 75 bps).
73,
Mike K2MK
Paul VanOveren-3 wrote
Some how I lost the text decode on the P3, can someone please tell me
from the PC. That's what many of us do.
But you would not use it for N1MM or some other critical application as you
would need that full time on your primary monitor. You might put your VE7CC
cluster program on the monitor shared with the P3.
73,
Mike K2MK
k6dgw wrote
1. Is the monitor
operate because there is no permissive signal.
And one last thought. Make sure you have adjusted the pot on the N8LP relay
such that the red LED lights when the SteppIR is tuning.
73,
Mike K2MK
Hunsdon Cary III wrote
Elecraft Reflector participants:
If any of y’all use the N8LP tuning relay w
Hi David,
Page 21 of the K3 manual. Right column under Programmable Functions.
You must have accidentally set the M1 button. Been there, done that.
73,
Mike K2MK
David Cole wrote
Hi,
I have recently been programming Macros... I noticed that now when in
CW mode, if I press the M1 front
or PRE, etc..
73,
Mike K2MK
JAY-3 wrote
On 20M the Sub receive dose not work.On all other bands when I turn on the
Sub I can hear signals on VFO B. When I try on 20M it is dead.I have
turned
the VFO A down so I hear nothing there and the B full volume and there is
nothing.
Where would I look
felt like
Q-tips piecing my ear drums. Ramping the AGC THR up to 020 is unthinkable
for me.
73,
Mike K2MK
Dave Hachadorian-2 wrote
My posting this morning about blowing the speaker amp chip was in
error. Further investigation reveals that I actually blew out
the K3's internal speaker
radial experiments that he conducted. It’s
wonderful stuff.
73,
Mike K2MK
Elecraft mailing list wrote
Most people would think we're well into Summer. Not here in the High
Rockies. Summer here has just begun. Time to mend some fences. Now
the point: I just pulled about a mile of #11 soft
Hi Bill,
I have the P3 with SVGA and have no additional noise on 6 meters.
73,
Mike K2MK
Elecraft mailing list wrote
Hello all:
I operate a lot of 6 meters an want to use the P3 band scope for weak
signal operating. However when I turn the P3/SVGA on my noise floor jump
up 3 or 4 db above
of the KPA500
and you'll see that the PR6 works as you would expect it to work.
73,
Mike K2MK
Dauer, Edward wrote
I need to ask for help configuring a PR6-10 on the K3. Installed OK,
removed the internal jumper per instructions and am using the control line
on a Y splitter to allow the KPA
position. I'm surprised they
haven't put a notch in the sheet metal to eliminate the need for this
alteration.
73,
Mike K2MK
W2RMS wrote
Hi everyone!
Finally assembled the KAT500 last night.
I never thought i would have this much difficulty with the tuner as
opposed to K3/P3.
Those SO-239
Hi Tighe,
No.
73,
Mike K2MK
Tighe Kuykendall wrote
Looked in the manuals and on my P3 but can't find this. Is there an
equivalent feature on the P3 SVGA option to get a marker line extending
down into the waterfall?
Tighe
NK4I
--
View this message in context:
http://elecraft
antenna. Removing pin 11 from the Aux cable to the KPA500 solved the
problem.
I'm surprised there is no mention of this problem and its solution in the
KPA500 manual. I think an alert should be added.
73,
Mike K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KPA500
Hi Fred,
If it is an older K3 then it's probably the knob. Contact Elecraft support
and ask them to send you two new knobs. If the RF knob isn't already cracked
it will someday. This is a known problem with older units.
73,
Mike K2MK
k6dgw wrote
Can't remember ever seeing this on the list
the screen. If
you can't do this then there could be a menu option to adjust the red cursor
width.
73,
Mike K2MK
Alan Bloom wrote
One change in the beta firmware is to make the width of the transmit
cursor in Data A mode equal to 2.7 kHz. The reason is that in Data A
mode there is no way
Hi Alan,
My apologies. I misread your prior posting. You said Data A and I misread it
as just Data. Please disregard my comments. You've got all of the bases well
covered.
73,
Mike K2MK
Alan Bloom wrote
On 04/26/2014 06:42 AM, Joe Subich, W4TV wrote:
I agree here ... FSK D, AFSK A, and PSK
the P3 screen as denoted by a small
arrow on the right or left side of the screen.
Experiment and have fun.
73,
Mike K2MK
hf4me wrote
I had just noticed those lines but didn't think they were necessarily the
transmit freq as I was in CW and the line wasn't at 600 as I would have
expected. Figured
the meter will
agree with the W2 and that you are not putting out any power.
Is it possible that your digital software is not activating the VOX or PTT.
If VOX is the issue it might be a simple matter of increasing the VOX GN
menu setting.
73,
Mike K2MK
Bob KD7YZ wrote
If I use CW then I get
. And while I am an electrical
engineer I think I explained this in layman terms.
73,
Mike K2MK
Dauer, Edward wrote
I am thinking of adding the SVGA option to my K3-P3. It would be neat to
have a single wide screen monitor running split screen, with the P3
display on one side and a logging/spotting
it
might be invisible when operating SPLIT. If you fiddle with the bandwidth
knob after pushing BSET you'll be able see the difference between the Red
and Magenta Cursors.
73,
Mike K2MK
G4HUE wrote
Just got the Sub RX and I must say it looks tasty. However, I am puzzled
by the display on the P3
Hi Larry,
One leg of the Y cable attaches to the SDA100. The other leg of the Y cable
attaches to the PC connection on the back of the P3. Then the separate RS232
cable supplied with the P3 goes between the XCVR connection on the P3 and
the RS232 connection on the K3.
73,
Mike K2MK
Larry
Hi Jan,
What is your antenna. There has been an ongoing thread on the SteppIR site
regarding this identical problem with many types of transceivers, not just
the K3. If you have a SteppIR antenna (any model) you should take a look at
their Yahoo site.
73,
Mike K2MK
Jan Ditzian wrote
I am
Hi Todd,
There is not. I always use headphones and one of my ears needs a slight
additional boost. I elected to purchase an external headphone amplifier with
individual gain and balance controls. I suppose something similar can be
done for speakers.
73,
Mike K2MK
todd ruby-2 wrote
with the necessity of pushing the P3 knob. I have
found this to be quicker, more accurate, and more intuitive then using
markers.
73,
Mike K2MK
Gary Smith-2 wrote
Reading the P3 screen I see a station transmitting. I use Marker A
(Green) to pin me on that desired station as soon as I tap the knob
to QSY
Hi Tom,
Set CONFIG:PTT-KEY to OFF-dtr.
73,
Mike K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/QSK-tp7585610p7585622.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing
Hi Stewart,
There may be a firmware solution to prevent this problem but I don't think
it advisable to ever ignore the power button. The Power Button is like an
Emergency Stop button. It needs to be 100% reliable.
73,
Mike K2MK
Stewart@twinwood wrote
If this is the case, then surely
level with the
CM500. Plus you can buy two CM500s (with change to spare) for the price of
one Proset.
73,
Mike K2MK
JBaumgarte wrote
I have 2 K3's which I use in a contest station I have, use for remoting
that station (35 miles from home), or the occasional mobile state qso
party.
I
shelf liner
and cut it out for the K3 speaker and vent holes. It kept the P3 from moving
around unless I got very rough with the buttons. I suppose the internal
speaker audio might be lessened slightly. I infrequently use the speaker and
I didn't notice any problem when I did use it.
73,
Mike K2MK
VFO-A.
73,
Mike K2MK
Gary Smith-2 wrote
Is there a way to have the marker track VFO A?
Along the same path, is there a way to have the marker stay on VFO A
and scroll as I adjust the K3?
It would be helpful to have see what is going on in the spectrum with
the P3 panadapter
that to trip a low current
device that in turn activates a relay.
73,
Mike K2MK
George A. Thornton-2 wrote
This might be a stupid question, but here goes.
I have a small lot. I currently am using a 3 element Yagi that barely
fits on the property. I was thinking about getting a vertical
K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-Text-Decode-Firmware-Request-tp7583908.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net
,
Mike K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Crystal-Filter-Offset-in-4-81-What-does-it-mean-tp7583674.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http
Hi Carl,
This has come up before on the reflector. It was caused accidentally as
follows. Somebody held the MENU button such that the K3 displayed uC 04.67
and FW REV5. Next they pressed the M1 button. That's all it takes to assign
a M key to a configuration function.
73,
Mike K2MK
Carl
for the SUB RX and the other leg goes to
the RX ANT IN BNC socket on the KXV3A board. When I want to use my RX
antenna for both receivers I press the RX ANT button. I'm still in diversity
but I'm using the same antenna for both ears.
73,
Mike K2MK
Gary Smith-2 wrote
I connect my Rx antenna via
if you take it to the Post Office but it is the same if you take it
to the UPS store. If you live in my town it will take 45 minutes at the Post
Office or 1 minute at the UPS store.
73,
Mike K2MK
Gary Smith-2 wrote
I'm going to be shipping my K3. Any suggestions on the most
affordable way
Hi Barry,
Hold the MENU button for several seconds and TERM will appear in the lower
display. I think this is what you want. Reverse the procedure and NORM will
appear.
73,
Mike K2MK
Barry wrote
I recall reading that a K3/100 can remotely control another K3, but can't
find the info now. Can
are already using your accessory socket you'll need a DB15 Y cable
which is available from Elecraft for a reasonable price.
I have the PR6-10 and I am very happy with its performance on all 3 bands.
73,
Mike K2MK
Stephen G4SJP wrote
Ray,
It fits neatly between the RX in and out BNCs
in.
The APF has its limitations.
73,
Mike K2MK
Bill W4ZV wrote
IMHO K3WC's APF suggestion is WAY TOO COMPLICATED. I use APF virtually
all the time and never use RIT, SHIFT, etc. Just HOLD DUAL PB to actuate
APF and use the VFO to zero beat. COARSE (10 Hz) VFO steps is usually
close enough
Hi Mike,
Not normal.
You may need to perform the K3 VFO noise mod. I had P3 grass on 6 meters
and the mod corrected the problem.
http://www.elecraft.com/K3/mods/K3_vfo_noise_mod_Rev_C.pdf
73,
Mike K2MK
Mike Reublin wrote
When I spin the VFO on my K3, the grass on the P3 increases
Hi Bud,
Split or XIT causes the RED transmit cursor to appear. The MAGENTA VFO
B cursor is turned on or off in the menu as posted by K5OAI.
73,
Mike K2MK
Bud Governale, W3LL wrote
P3:If I turn on Split I see the sub receiver cursor along with VFO A.
However if I just turn on the sub
and
the ability to send macros from the keyboard. Detailed explanations can be
found in the P3 SVGA manual. You can also just use the keyboard for it's
ability to store and recall numerous macros.This can be a lot of fun if you
are into K3 and P3 macros.
73,
Mike K2MK
Gary NL7Y wrote
After some
is to
quickly toggle from Fixed Tune to Tracking and back to Fixed Tune. I do this
by setting the menu option of FixTrack as a top row function key. A quick
double tap of the function key moves the station to the center of the
screen.
73,
Mike K2MK
k6dgw wrote
I run my P3 in fixed-tune mode [span edges
meters on my K3.
An upgrade (not really a mod) was the exchange of the DSP board. This made
my K3 sound quieter to me. I think you have to hunt around the Elecraft
website to find this one.
I did the mods myself so I can't comment on the factory cost.
73,
Mike K2MK
Gary Smith-2 wrote
I
antennas more, and/or provide external protection.
The diagram on page 42 of the K3 manual illustrates the presence of the
COR(s).
73,
Mike K2MK
K4FJ wrote
Am I correct in assuming that the Rec Ant input is disconnected from the
main receiver input upon transmit by way of a relay? If so, can I
Hi Paul,
Check your RX EQ settings.
73,
Mike K2MK
Paul Milward wrote
Hi gang
I have a very strange condition with my K3. Absolutely no reception in CW
mode on any band. There is dead quiet, no noise no static. It looks as
though I can xmit CW, as the red LED lights.
All other modes
instead of gibberish
on the external monitor used with the P3.
73,
Mike K2MK
Randy Moore wrote
Last night I returned to 20m RTTY for the first time in several days and
the baud rate had reverted to 75 bps. I am certain it was 45 the last
time I was there. ???
73,
Randy, KS4L
On Oct 23, 2013
Hi Bud,
The P3 and K3 are connected on one leg of the Y cable per the diagram in the
P3 manual. The SteppIR controller connects to the other leg per the drawing
supplied by SteppIR. If you need a copy of the SteppIR connection send me a
direct e-mail and I'll send it to you.
73,
Mike K2MK
Bud
Hi Fred,
You probably mean you use AFSK A for RTTY. For JT65-HF you want DATA A. LINE
IN is correct and MIC+LIN off is correct although I suspect the K3
automatically turns MIC+LIN off in any of the data modes.
I use VOX for all data modes. Never had a problem.
73,
Mike K2MK
k6dgw wrote
Hi Brian,
Check CONFIG:SPKR+PH.
I forget the reason why but the right ear is muted if SPKR+PH is YES and
CONFIG:SPKRS is 1.
73,
Mike K2MK
K1LI wrote
Suddenly, I can't hear the sub-receiver in the right headphone unless I
use
the Ab-b option on the L-MIX-R menu item. (FYI, the b-Ab option
. Then adjust your width
knob until the filter width is correct for PSK. I suppose something around
2KHz or greater. Whatever you prefer.
73,
Mike K2MK
Ed-3 wrote
When I switch my K3 to the data mode I do not hear any signals. I hear
plenty of PSK in USB on 20 meters and DM780 will decode them when
Hi Gary,
The quickest way to determine if the P3 is talking to the K3 is to look at
the top of the P3 display. If the current K3 frequency is not displayed in
the center of the screen then you have not established communications.
73,
Mike K2MK
Garry Shapiro wrote
I have had a P3 for some time
Hi Alan,
Of course it could be as simple as the P3 and the computer not being set to
the same baud rate. If not that I would next try removing the serial
connection to the K3 and just have the computer go directly to the P3.
73,
Mike K2MK
Alan Grant wrote
I recently attempted to down load
0) ends up being too large. If Elecraft wants us to use
1440x900 on a 1920x1080 monitor they should probably include an additional
font that is extra small.
73,
Mike K2MK
Don Wilhelm-4 wrote
Mike,
If you read the P3SVGA manual, it states that For faster screen updates
when using fixed tune
Hi Bill,
Help us by stating your firmware rev levels. Latest Updates might not
include Beta releases for some folks.
73,
Mike K2MK
Bill W2BLC wrote
Latest updates have been made and factory cables are being used.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3
is 1.26 and SVGA firmware is 1.16.
Are there any solutions out there or is everybody using 1440x900.
73,
Mike K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/P3-SVGA-display-problem-1920x1080-tp7579216.html
Sent from the Elecraft mailing list archive at Nabble.com
guess at what I did. I
don't remember things like I used to.
73,
Mike K2MK
JBaumgarte wrote
Along the same line, when I go back to RTTY, it comes up at 75 baud, where
it was last at FSK-D and 45 baud. I'm using the remote system if that
makes any difference.
John, N0IJ
Sent from my iPhone
attenuator or by using the K3 pre-amp. Or we use an external amplifier with
the RX antenna. By taking these steps an additional loss of 3db signal +
noise should not be a show stopper.
73,
Mike K2MK
dw-4 wrote
Thanks for posting this Pete!
Are you noticing any observable decrease in signal
it is.
Check CONFIG:L--MIX--R. For the simplest type of operation you want A-b.
73,
Mike K2MK
Jeff Hall, W6UX-2 wrote
I haven't used my K3 much since Field Day. Today I turned it on and
engaged the sub receiver by tapping SUB. Instead of hearing VFO B in my
right ear, I only hear VFO A in my
Hi Hisashi,
The P3/SVGA board is acting as a terminal. It does not do any decoding. It
just displays the decoding done by the K3. If you're missing characters you
may want to adjust the threshold on the K3. See the decode tips in the K3
manual on page 33.
73,
Mike K2MK
Hisashi T Fujinaka wrote
Shack but these
cables would be much cheaper with greater variety on-line from places like:
http://www.cablewholesale.com/index.php
http://www.monoprice.com/
http://www.amazon.com
73,
Mike K2MK
Steven Bertsch wrote
My friend wants to use MMTTY with his K3/0 remoting to my K3. He wants to
use
disappears.
The REF LVL will need to be changed from band to band but the P3 remembers
the setting on each band. Of course the level also changes with atmospheric
conditions, time of day, antenna direction, etc..
73,
Mike K2MK
Hisashi T Fujinaka wrote
I just got my P3 SVGA card and it's just showing
Hi Tim,
Drinking the Kool Aid is a derogatory expression. See the following:
http://en.wikipedia.org/wiki/Drinking_the_Kool-Aid
73,
Mike K2MK
Gary W. Hvizdak wrote
Tim Hague (M0AFJ) asked ...
Could someone tell us non-Americans what Kool-Aid is?, and if it's so good
for stress where can we
Hi Trevor,
I'm waiting for a KPA1000. But I'd also take a KPA1200 or KPA1500.
73,
Mike K2MK
Trevor Dunne wrote
Hi All
I have been reading the mail here for some time while I debate the
purchase of a K3 in my head. I can't help to notice the lack of subjects
covering the K3 and the lack
to the
test points for a voltage measurement that translates to watts of output per
the chart in the manual.
73,
Mike K2MK
Rick Bleda wrote
I feel like the dummy, but I just bought and put together the DL-1 from
Elecraft, and I have no clue how to use it. Can someone help? I need step
by step
using the K3 Utility.
The outer volume knob (Sub) can be configured to be a true volume control or
a balance control using CONFIG:SUB AF. Check which you have chosen.
73,
Mike K2MK
Dauer, Edward wrote
Just finished the K3 and have it on the air. Neat! Much to learn yet.
Two questions
say should be because I never actually tried
making changes using BSET while in diversity.
I also have the Pixel and am happy with it.
73,
Mike K2MK
Robert Fanfant-2 wrote
All,
Apologize if this question has been asked before.
When handling pileups, I've always used the following setup
be rewarded with 2 or 4
real serial DB9 connectors with real numbers such as com 1, com 2, etc..
73,
Mike K2MK
Goldtr8 (KD8NNU) wrote
Gents,
I wish to get a new computer for the shack and want to have one that is RF
quiet and has real serial ports.
I am guessing that others have purchased some
Hi Don,
Is it possible that you have another PC program in communication with the
K3. Perhaps a logging program. That could make the com port busy.
73,
Mike K2MK
haircut...@verizon.net wrote
Hello Group,
Checking my K-line setup, noticed the my utility for the Kat500 wasn't
reading
signals that are several minutes old. I never
measured the time duration and of course it would vary depending on how tall
you make the waterfall. Needless to say it is well in excess of 10 seconds.
In my opinion the SVGA option for the P3 is worth the price of admission.
73,
Mike K2MK
Hank
. If you go this way you'll want a monitor
that has front panel button for input selection as opposed to input
selection through a menu.
Enjoy your SVGA board. It really enhances the K3/P3 experience.
73,
Mike K2MK
atoyer wrote
I have recently received the P3SVGA and need to procure a suitable
Hi Bill,
I have a weak ear and use a Behringer AMP800 between my K3 and my CM500
headphones. Works great. Around $70 on Amazon.
73,
Mike K2MK
quote author=Bill Clarke
I have a problem with a weak ear. To circumvent this, I use a Behringer
mixer panel, allowing me to control the gain for each
I am selling my one year old PR6 Preamplifier for 6 meters. It includes the
original packaging, manual, cables, connector, and BNC adapters. It
functions perfectly. Asking $110 plus shipping. Please contact me directly,
not through the reflector. k2mk at comcast dot net
73,
Mike K2MK
--
View
101 - 200 of 512 matches
Mail list logo