Hi everybody,
just to let you know:
while preparing my gear for WWDX I noticed that the P3 started to freeze
the display for about 1 second, than continues to work for 2-3 seconds,
then freezes, and so on. Very annoying to look at.
I disconnected all cables and traced it down to the
My P3 display freezes momentarily. It’s intermittent, I checked all the
cables.
What does the blinking red light in the box do, don’t remember and can’t find
it in the manual
Ray
W8LYJ.
Sent from my iPad
__
Elecraft mailing list
Subject: [Elecraft] P3 Display Flashing
Just setting up for field day and my P3 has developed a problem. About 5
seconds after startup the spectrum box clears and redraws about once a
second. While it is blank the text "5 ms / div" appears in the lower left
corner outside of the waterfall
Just setting up for field day and my P3 has developed a problem. About 5
seconds after startup the spectrum box clears and redraws about once a
second. While it is blank the text "5 ms / div" appears in the lower left
corner outside of the waterfall box.
Any ideas?
Glenn KD0Q
Hi Robin,
Make sure you have the P3 and K3 connected via the 9 pin RS232 cable, and that
both are at the same baud rate mentioned the manual.
Also, in the P3 menu there is an entry for radio type. Select K3 if it is not
already entered.
73,
Eric
/elecraft.com/
On 4/18/2019 7:32 AM,
] On Behalf Of oz6...@qsl.net
Sent: Thursday, April 18, 2019 4:33 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 Display issues...
Hi -
I just cannot get this to work for me. I am looking at my P3 connected to a
K3. It is connected between the IF In on the P3 and IF Out on the K3. When
Robin,
Do you have an RS-232 9 pin cable connected between the K3 RS232
connector and the XCVR connector on the K3? That cable is what carries
the frequency and other information to the P3.
For computer connection, connect the PC to the "PC" connector on the P3.
If you have a K3S and are
Hi -
I just cannot get this to work for me. I am looking at my P3 connected to a K3.
It is connected between the IF In on the P3 and IF Out on the K3. When looking
at the P3 display, on all frequencies, I do not see the actual frequency of the
VFO, I see 0, for example to top line has
Hi -
I must be a complete idiot, but I just cannot get this to work for me. I am
looking at my P3 connected to a K3. It is connected between the IF In on the P3
and IF Out on the K3. When looking at the P3 display, on all frequencies, I do
not see the actual frequency of the VFO, I see 0,
This is what I do. Then I read the noise level in dBm from the screen. Very
useful to compare noise levels at different times, etc.
But what I would like is a menu command that could be assigned to one of the
function keys to automatically compute the average noise level and then adjust
the
Hi Martin,
I have a somewhat different solution to your problem, and it consists of
multiple parts.
First, I set averaging to maximum (I set it years ago, don't ask me
numbers). :)
Second, I set Scale to 24 dB when I'm not contesting, 32 dB for 100W
contests, 42 dB for high power
I'm not all that familiar with the Flex stuff but in some SDR software
display systems it is possible to adjust the waterfall sensitivity and
contrast independent of any spectrum bandscope position adjustment. It
is often also possible to have any signal levels indicated by such
displays bear
Hi Jim,
They may be automatically calculating a long-term-average noise floor, then
subtracting it from the waterfall. The P3 could do the same thing. But
automatic noise subtraction would have the same disadvantage as slow AGC: a
temporary rise in the noise floor would mask weak signals for
I saw a demo last night of the FlexRadio bandscope. It showed the noise
well above, on the Y-axis, the bottom of the display, but the waterfall
didn't show the noise, just the signals on the band.
When I set the REL LVL on my P3 so the noise floor is below the noise, the
waterfall is blue
To: Elecraft@mailman.qth.net
Subject: [Elecraft] P3 display flashes when sdrplay active from IF Out
I noticed that when I have an SDRPlay RSP 2 active that the P3 display
flashes. The SDR is connected to IF Out on the P3.
Has anyone else seen this happen?
Thanks
Tom NY4I
Principal Solutions Architect
I noticed that when I have an SDRPlay RSP 2 active that the P3 display flashes.
The SDR is connected to IF Out on the P3.
Has anyone else seen this happen?
Thanks
Tom NY4I
Principal Solutions Architect
Better Software Solutions, Inc.
727-437-2771
I experienced this problem when I first got my P3. The fix was simple:
replace the coax patch cable between the K3and the P3. It has been fine
ever since.
Bill W2BLC K3-line
--
Many of life's problems can be solved by simply deciding what
we can do without. - John Dolan
It's leakage of an internal signal from the K3 [or maybe even the P3 but
I doubt it] into your P3, most probably through the cabling. It moves
when you tune because it's coming from the radio. It's like some fairy
tale or bad dream... you can chase it but you'll never ever catch it. [:-)
Check that your cables are tight.
On 6/4/2017 10:23 AM, Mike Weir wrote:
Yesterday while on the radio I notice on my P3 screen a signal (so I thought)
the band was basically dead other than this signal. As I tried to tune to it
the signal would move. No matter how close I tried to get to the
Yesterday while on the radio I notice on my P3 screen a signal (so I thought)
the band was basically dead other than this signal. As I tried to tune to it
the signal would move. No matter how close I tried to get to the so called
signal it kept the same distance from my VFO A tuning indication.
Thanks
Bill - W0BBI
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help
Over the course of the last several weeks my P3 Display has developed an
annoying white "flashing or blinking" in the lower half of the display. To be
more accurate, it is in the lower portion of the receive signal display. That
is if I have "labels" enabled, it does not flash/blink in that
If you don't have the latest P3 software, this may be the cause...
There was an issue when stacking macros, whereby a macro failed in
interesting and odd ways depending-- on the previous macro command...
They would work fine if executed in the MACRO editor Elecraft provides,
as long as you did
Hi Tony,
I use this macro for split and it works for me:
BW0001;SWT13;SWT13;FT1;UPB7;RT0;XT0;#SPN60;#RCF+002500;BW0280;
BW Sets bandwidth to as narrow as possible...
SWT13 Copies the current vreq to VFO B
FT1 Selects VFO A
UPB7Moves the VFO A up 5
RT0/XT0 Clear RIT and
Hi Bill and others,
The split macro does move the B vfo up by 1khz but this is not shown on
the display (Red band) until i manually move the B vfo even just one
digit. The prob is not data cable cons but thanks for the thought. I may
try changing the order of some of the things in the macro or
If you're saying "with both VFOs on same freq, the P3 doesn't show the red band
indicating that VFO B is the TX freq. " that's normal. Since both are on same
freq the VFO B cursor is hidden behind the green VFO A cursor.
But I may have misread your post.
Sent from my iPhone
...nr4c. bill
>
Hi All,
I have noticed a little problem (not much) with the P3 display. I have
A K3 P3 and vga card set up as per the book and work fine until I go
from normal to split working. I achieve this with a macro on the K3. The
problem is the K3 goes into split but the display on the P3 and monitor
Thanks for the help. The parameter initialization did it. This is the
first time I have had to do this and I pretty much figured I had changed
something inadvertently. I probably did, but this cut to the chase so i
wasn't trying to find out which one.
Once again thanks.
Russ Edelen, KG7VQ
I don't know what happened but my P3 suddenly has no spectrum display
and the waterfall is solid pink at all span settings. I tried to reset
the reference level but the only setting option available is nan.
The P3 still tracks the K3 VFO. I tried to reset the scale, power cycled
the P3,
Russ,
That's pretty bizarre. Try doing a parameter initialization as
described in the Troubleshooting section of the manual.
Alan N1AL
On 03/30/2014 05:10 AM, Russ wrote:
I don't know what happened but my P3 suddenly has no spectrum display
and the waterfall is solid pink at all span
Hi Tim,
Are you using Fixed Tune mode on the P3/SVGA? In Fixed Tune mode, there is
quite a bit if information passing between the K3 and P3/SVGA and it sounds
like the Commander polling is affecting this communication. Try using
Tracking Mode on the P3/SVGA and see if that solves the hanging
Paul,
I have been using Fixed Tune mode with the P3 and Commander as
long as it has been available in the P3 without any hang. I
do keep Commander's Command Interval (polling rate) at 200 ms
or higher (slower) but that is primarily to handle the worst
case dead time in the K3 when changing
Paul,
I was using the fixed mode, but have since changed the USB adapter to a FTDI
adapter and so far have not had any hang ups, if I do, I'll try changed the
mode to see if that helps.
Thanks for the response.
Tim
NZ8J
__
Elecraft
Hmm... I too am using fixed tune mode, and the DXlab Commander and have never noticed this
problem. My poll rate in Commander is set slow, 300 ms.
On 11/11/2013 7:37 AM, Joe Subich, W4TV wrote:
Paul,
I have been using Fixed Tune mode with the P3 and Commander as
long as it has been available
That's great Tim, glad you got it working. This is one of the reasons
Elecraft uses FTDI chip sets in the KXUSB and KUSB cables.
-Paul
Paul Saffren - N6HZ
Project Manager
Elecraft Inc.
831-763-4211 x122
www.elecraft.com
On 11/11/2013 8:28 AM, Tim Cook wrote:
Paul,
I was using the fixed
I have a K3/P3(w/SVGA) connected to DXLabs Commander and the P3 display
hangs from time to time. By hang, I mean it just freezes for a second
or two periodically then starts working again by itself, I do not have
to do anything to restart it.
It seems to be connected to Commanders polling the K3
Well, after several very informative replies to my post, I've come to the
determination that I'm not the only one seeing these Flying Fribbles, Moving
Humps, Sweepers, Chirpsounders, Beacons, SeaSonde, etc. Of course,
it's just possible that there is a cloaked ship up there that is scanning
Just wondering if I am the Lone Ranger here or if anyone else is having this P3
experience. Every so often, perhaps once every 20 - 40 seconds or so, I see
some sort of spur go flying across the screen. It starts low and flies up in
frequency, right off the display. With my display span set at
Disconnect your antenna, set the REF LVL on the P3 so you can see the
background noise at the base of the display and watch it for a while. If you
no longer see it, it isn't in the K3/P3 anywhere and is external to the radio.
I have several sweepers that come through from time to time. One is
On 3/15/2012 4:00 PM, Jim Bennett wrote:
Just wondering if I am the Lone Ranger here or if anyone else is
having this P3 experience. Every so often, perhaps once every 20 -
40 seconds or so, I see some sort of spur go flying across the
screen. It starts low and flies up in frequency, right off
On Thu, Mar 15, 2012 at 6:00 PM, Jim Bennett w6...@mac.com wrote:
...Every so often, perhaps once every 20 - 40 seconds or so, I see some sort
of spur go flying across the screen.
I see 'em too, Jim, and I know they're for real because I can hear
them in my headphones. I
and microwaves!
Cheers
Simon ZL4PLM
Check out more information on the world 50 MHz and Up : www.zl4plm.com
Date: Thu, 15 Mar 2012 20:04:43 -0500
From: estept...@gmail.com
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 Display Anomaly
On Thu, Mar 15, 2012 at 6:00 PM, Jim Bennett w6
On Thu, Mar 15, 2012 at 8:11 PM, Simon Lewis gm4...@hotmail.com wrote:
They are chirpsounders...
=
Ah yes, now I remember hearing that name. Thank you, Simon Those are
the sweeping beacons I mentioned.
Google on 'chirpsounder' and you'll find a strange world of
propagation
and microwaves!
Cheers
Simon ZL4PLM
Check out more information on the world 50 MHz and Up : www.zl4plm.com
Date: Thu, 15 Mar 2012 20:04:43 -0500
From: estept...@gmail.com
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 Display Anomaly
On Thu, Mar 15, 2012 at 6:00 PM, Jim Bennett
Sorry if this problem has been reported/discussed earlier.
Problem: Playing CW messages from K3/Mx freezes the P3 display until a
message has been sent.
Any help?
73, Heinz HB9BCB
--
View this message in context:
This sounds normal. P3 display always freezes during transmit. (Unless you
disconnect the RS232 cable to the K3).
73,
Bruce, N1RX
Problem: Playing CW messages from K3/Mx freezes the P3 display until a
message has been sent.
__
I wonder why ELECRAFT has choosen a different design approach to mute the K3
IF signal to the P3:
K3 internal keying (by paddel jack or by M1-M8):
IF signal is fully muted (P3 display freezed)
-- allows no monitoring of spectrum and transmitted signal while keying
-- P3 diplay does not support
Hello friends.
My P3 is coming this week.
Is there options for change color of display (background, text,
waterfall, etc) ?, maybe via P3 Utility.
Never have seen a P3 using different color set to presented in
Elecraft site and other web pages.
I've been thinking of asking this same question. I'd -really- like to have
an
amber background with black information display. (Like the Decca RADAR
I used to use.) (:-)
73!
Ken - K0PP
2012/1/16 Eduardo González edujo...@gmail.com
Hello friends.
My P3 is coming this week.
Is there
The next firmware revision will have an option for a monochrome
waterfall, primarily to accommodate color-blind operators.
Alan N1AL
On Mon, 2012-01-16 at 15:47 -0430, Eduardo González wrote:
Hello friends.
My P3 is coming this week.
Is there options for change color of display (background,
On 1/16/2012 12:29 PM, Alan Bloom wrote:
The next firmware revision will have an option for a monochrome
waterfall, primarily to accommodate color-blind operators.
which would be me. Thank you Alan. Can't name another company that
would do something like this.
73,
Fred K6DGW
- Northern
[Yes, it seems trivial, but it would sure be a nice feature to say (without
mental computations) There is a clear spot, up 5.2 KHz, let's move there]
Just a note to say I use the marker (cursor) to tell me what the frequency is
of a clear spot, etc,
so that I don't have to do the mental
Sorry if this topic has been discussed earlier.
What about a new P3 menu entry allowing to select frequency scale
lines/markings (similar to the menu Lvl Lines plus on/off)?
Heinz, HB9BCB
--
View this message in context:
I have to agree. At least put values on the hash marks that change with the
span width (from center) so I don't have to compute them mentally with each
span setting?
Yes, it seems trivial, but it would sure be a nice feature to say (without
mental computations) There is a clear spot, up 5.2
Hi guys. I've just hung together my new P3 and have noticed a couple of
things that I can't recall as having been raised before.
On test, I noticed that the display wasn't quite square with the front panel
aperture. It runs out only a millimetre or so, but it was the first thing
that
I have a question about the P3 -- the cursor width shows the filter width. But
the P3 shows signals outside of the filter bandwidth. This must mean that the
sample of the IF signal is before the roofing filters. If that is the case
then I am assuming that the signal within the frame of the
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 display...
I have a question about the P3 -- the cursor width shows the filter width.
But the P3 shows signals outside of the filter bandwidth. This must mean
that the sample of the IF signal is before the roofing filters. If that is
the case
Well, the signal you see within the U-shaped cursor is the signal that
*will* pass through the first I.F. (roofing) filter but, as you note, the
I.F. is being sampled before actually passing through the to show the
signals outside of the filter bandwidth.
Ron AC7AC
-Original Message-
I
, 2011 11:57 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 display...
I have a question about the P3 -- the cursor width shows the filter width.
But the P3 shows signals outside of the filter bandwidth. This must mean
that the sample of the IF signal is before the roofing filters
...@mailman.qth.net] On Behalf Of Phil Hystad
Sent: Wednesday, February 23, 2011 11:57 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 display...
I have a question about the P3 -- the cursor width shows the filter width.
But the P3 shows signals outside of the filter bandwidth. This must mean
.
Bill
K9YEQ
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Phil Hystad
Sent: Wednesday, February 23, 2011 11:57 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 display...
I have a question about the P3
Months ago I had heard a rumor that the P3 could eventually function as a
read-only display that could inform the operator of these various settings.
Al W6LX
(Subject: line changed to reflect the current topic.)
There's a great need for some simple utilities for the K3
that will run with
I've noticed the following problem for the past couple of releases of K3 and
P3 software. Since my P3 is fairly new, I don't know if it's always been
there or not. I'm running the current software on both K3 and P3.
When I turn on power to the K3, the P3 comes on, too. Often, the display of
When using REV button on K3, P3 display frequency marker freezes and does not
track K3 frequency change - anyone else seeing the same problem? Firmware is
036 for P3.
Only soloution is to switch P3 off and back on.
73 Dave G0AIX
__
REV button? I can't find any REV button on either of my two
K3s.
73,
... Joe, W4TV
On 9/22/2010 2:38 PM, David wrote:
When using REV button on K3, P3 display frequency marker freezes and
does not track K3 frequency change - anyone else seeing the same
problem? Firmware is 036 for P3.
Look at the numeric keypad --- #2
On Sep 22, 2010, at 2:04 PM, Joe Subich, W4TV wrote:
REV button? I can't find any REV button on either of my two
K3s.
__
Elecraft mailing list
Home:
Yes, that seems to be the case. Once the REV button has been pressed, the
markers no longer track tuning, but remain at a fixed location. Same for both
Marker A and B
Grant/NQ5T
When using REV button on K3, P3 display frequency marker freezes and
does not track K3 frequency change -
David
I have the same problem here, well found!
Using latest firmware in both K3 and P3.
73 Stephen G4SJP
On 22/09/2010 19:38, David g0aixda...@aol.com wrote:
When using REV button on K3, P3 display frequency marker freezes and does not
track K3 frequency change - anyone else seeing the
Also, it appears that the tap-to-tune function does work properly after the REV
button is pressed either.
Grant/NQ5T
On Sep 22, 2010, at 2:12 PM, Grant Youngman wrote:
Yes, that seems to be the case. Once the REV button has been pressed, the
markers no longer track tuning, but remain at a
Subject: Re: [Elecraft] P3 Display Problem
REV button? I can't find any REV button on either of my two
K3s.
73,
... Joe, W4TV
On 9/22/2010 2:38 PM, David wrote:
When using REV button on K3, P3 display frequency marker freezes and
does not track K3 frequency change - anyone else seeing
I've notified Alan about this.
73,
Eric
On 9/22/2010 1:26 PM, Grant Youngman wrote:
Also, it appears that the tap-to-tune function does work properly after the
REV button is pressed either.
Grant/NQ5T
On Sep 22, 2010, at 2:12 PM, Grant Youngman wrote:
Yes, that seems to be the case.
Thanks, Dave. I confirmed the bug. You must be the first person with a
P3 to press the REV button!
Wayne and I are working on it.
Alan N1AL
On Wed, 2010-09-22 at 19:38 +0100, David wrote:
When using REV button on K3, P3 display frequency marker freezes and does
not track K3 frequency
#2 button top right next A/B
--
View this message in context:
http://elecraft.365791.n2.nabble.com/P3-Display-Problem-tp5560268p5561322.html
Sent from the [K3] mailing list archive at Nabble.com.
__
Elecraft mailing list
Home:
Here's a simple (hopefully) question ...
The answer is a little complicated. :=)
First, the 10 dB noise figure is for the P3 itself. The total noise on
the display includes the contribution from the K3. Assuming you have
done the IF Out mod on the K3, the noise figure of the K3/P3
There is a repeatable problem in the P3 display of the bandwidth
cursor in AFSK A and FSK D data sub-modes. In both submodes the
VFOs (correctly) display the RF frequency of the MARK (as set by
Pitch). However, the P3 displays the filter limits as if the
mark frequency were always set to 915
Joe Subich, W4TV-4 wrote:
There is a repeatable problem in the P3 display of the bandwidth
cursor in AFSK A and FSK D data sub-modes. In both submodes the
VFOs (correctly) display the RF frequency of the MARK (as set by
Pitch). However, the P3 displays the filter limits as if the
Thanks Bill.
73,
... Joe, W4TV
On 8/8/2010 10:14 PM, Bill W4ZV wrote:
Joe Subich, W4TV-4 wrote:
There is a repeatable problem in the P3 display of the bandwidth
cursor in AFSK A and FSK D data sub-modes. In both submodes the
VFOs (correctly) display the RF frequency of the MARK
I know that the refresh rate is planned to be going faster here soon but
is there any chance of a simple video so that we may see it in its
active state?
~Brett
On Fri, 2009-08-21 at 17:27 -0700, Eric Swartz - WA6HHQ, Elecraft wrote:
Believe me, the usable spectral display is much larger
Well said Dave.It is a must for us oldies along with
the ability to change font size and display digital modes.
Peter G3UCA
I finally obtained an answer to my question..
The display area is 4.5 inches diagonal. That's about the same screen
size as my SatNav,
Not until later. We are hot in development at the moment and there are a
limited number of P3s.
Ask anyone who was at the Santa Barbara show last weekend and they will
tell you it was very fast :-)
73, Eric
Brett Howard wrote:
I know that the refresh rate is planned to be going faster here
We're happy with the number and placement of the buttons and switches at
this time. This front panel and active matrix display parts of the
design (except for the silkscreen button labels, which will be changing
a bit) is already final, due to the long lead time on these components.
Note that
We already plan to offer a VGA output option.
To clarify this a bit, there its is not as simple as connecting a VGA
connector to the display. VGA output actually required additional memory
and a display procesor dedicated to that output path. WE've thought this
through carefully and have
One note on these early P3 pictures.
Several people noted in private emails that the absolute dbM range on
these screen shots (see email below) implied a high noise floor and that
the scale did not go down to the K3s noise floor. The development
firmware used for these pictures was an early
Eric Swartz -WA6HHQ, Elecraft wrote:
The P3 has excellent sensitivity and can display signals down close to
the K3s noise floor. Actually, with signal averaging enabled, the P3 can
show -very- weak signals, especially on the waterfall display. I'm
already hooked on the short time I've
The IF output buffer mod is perfectly OK with the P3. We've refined and
simplified the mod to a 1 resistor change and will be posting a mod note
next week.
73, Eric WA6HHQ
_..._
Pete Connors wrote:
Eric Swartz -WA6HHQ, Elecraft wrote:
The P3 has excellent sensitivity and can display
I finally obtained an answer to my question..
The display area is 4.5 inches diagonal. That's about the same screen size as
my SatNav, assuming a similar aspect ratio.
I was also unsure whether the display was LCD or OLED. It has been confirmed
that it is a TFT LCD.
I'm certainly
Believe me, the usable spectral display is much larger compared to the
spectrum displays on other rigs. We use the wole screen for the dislpay,
as opposed to rigs like thePRO-III that only use the bottom 1/4 of their
displays for the panadapter. I'm a 52 yr old reading glasses kind of guy
and
Eric Swartz wrote:
It would be hard to get something much larger into a matching enclosure.
Eric, have you considered placing some of the buttons on the top of the
enclosure near the front. This
would make room for a larger display size and the push down pressure would
also help hold the P3
(Snip)
I like this. But if it's done don't display the same information on the P3
and the monitor. The Icom 7700 does this and it appears repetitive to
display the same thing twice.
73 Jeff kb2m
(End snip)
Jeff,
I would use the display feature purely as a means to be able to leave my
glasses
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of rfenab...@gmail.com
Sent: Thursday, August 20, 2009 8:07 AM
To: Elecraft
Subject: [Elecraft] P3 Display
(Snip)
I like this. But if it's done don't display the same information on the P3
and the monitor. The Icom 7700 does this and it appears repetitive
of the performance
that display brings.
~Brett
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of rfenab...@gmail.com
Sent: Thursday, August 20, 2009 5:07 AM
To: Elecraft
Subject: [Elecraft] P3 Display
(Snip)
I like this. But if it's done
One of the things that can be confusing is a very busy display. I think all
that should be highlighted on the panadaptor display is the DSB bandwidth. That
is what bandwidth you are receiving, not the crystal filter bandwidth.
73
Dave KD1NA
Message from Wayne:
However, the P3 will be aware of
David Robertson wrote:
One of the things that can be confusing is a very busy display. I think all
that should be
highlighted on the panadaptor display is the DSB bandwidth. That is what
bandwidth you are
receiving, not the crystal filter bandwidth.
This is indeed very useful, but you
And have no fear, we're not going to add 'wallpaper' backgrounds to the
P3 display ;-)
73, Eric WA6HHQ
That tears it for me! I have to have purple Kansas State PowerCat
wallpaper!!!
;)
73, Bill nz0t
--
View this message in context:
I'd rather put a KPA800 inside ;-)
73
Roger MW0IDX
K3 #191
K2 #2724
KX1 #416
But we'll supply simple P3-to-K3 support hardware to ensure that
the P3 doesn't move when you push the buttons. Or you can weight it
down by putting your own power supply inside, which is what I plan to
do :)
Kevin wrote:
How about if we have it sing the national anthem, proper selection for
DX of course, brew the coffee, and cook breakfast while we're at it? How
about voice recognition so you'll never have to touch another knob?
For crying out loud!
Actually, I was hoping it would have a rear
the bottom-right side of the transceiver. Simply plug the phone line into
it and caller-ID displays right above the S meter.
I had a fleeting thought that someone would take my comment seriously.
Please do not connect your telco line into the K3's RJ-11 jack. An active
phone line carries
Can we have a choice of Anthems please?
:-)
73 de M0XDF, K3 #174
--
A bit of fragrance always clings to the hand that gives the rose.
-Chinese proverb
On 18 Aug 2009, at 00:28, R. Kevin Stover wrote:
How about if we have it sing the national anthem,
--
Children aren't happy without
Yes, I want mine to sing This Land Is Your Land,...
73, doug
From: David Ferrington, M0XDF m0...@alphadene.co.uk
Date: Wed, 19 Aug 2009 00:10:43 +0100
Can we have a choice of Anthems please?
On 18 Aug 2009, at 00:28, R. Kevin Stover wrote:
How about if we have it sing the
The P3 is connected to the K3 at a point ahead of the crystal filters,
so when you change crystal filters on the K3, it won't change the P3's
displayed waveform.
However, the P3 will be aware of the K3's filter bandwidth and offset,
so we can show a bracketed or otherwise highlighted area
1 - 100 of 110 matches
Mail list logo