Bert always amazing hope you are well. Regards Paul. On Fri, Oct 22, 2010 at 6:02 PM, <[email protected]> wrote:
> Send me a picture direct to my email. I may have one. Bert Kehren > > > In a message dated 10/22/2010 6:01:13 P.M. Eastern Daylight Time, as > [email protected] writes: > > With an outboard +/- 12 Volt power source my 2100F is now working fine. > A new replacement package is therefore desperately needed. > > Best regards, > Antonio > CT1TE > > Quoting [email protected]: > > > Dear All, > > > > Diving into the hardware, I found the DC-DC +5 to +/-12 V Power Source > > defective. There may be something more but that is serious enough. > > > > Thank you for your kind attention and help. > > > > Antonio > > CT1TE > > > > Quoting paul swed <[email protected]>: > > > >> Thats what I was thinking also on the reference and emailed back to the > >> group. > >> I believe over time that internal switch to select 1,5,10 mc can get a > bit > >> touchy. > >> If a operating reference is connected and checked to be correct toggle > the > >> switch a few times to clean its contacts. It gets lonely sitting in > there by > >> itself for years. ;-) > >> Regards > >> Paul. > >> > >> On Fri, Oct 22, 2010 at 8:12 AM, Chuck Harris <[email protected]> > wrote: > >> > >>> Hi Antonio, > >>> > >>> Ok. I just wanted to be sure that it was still up in Europe. Canada > >>> dropped their chains 3 months earlier than they said they would. And > >>> since Loran-C is no longer usable world wide, I figure Europe will be > >>> dropping their chain soon. > >>> > >>> The error indication you have described tells me that you have no > >>> reference oscillator. This could be for a couple of reasons: > >>> > >>> 1) you have no frequency standard connected to your 2100F > >>> 2) the switch, labeled 1-5-10, on the board stack visible when you > hinge > >>> open the front panel is set incorrectly for your external frequency > >>> standard. > >>> 3) Your 2100F is broken. > >>> > >>> -Chuck Harris > >>> > >>> [email protected] wrote: > >>> > >>>> Chuck, > >>>> > >>>> I am in Portugal, currently receiving the European > >>>> 6731 LESSAY Chain. > >>>> > >>>> Best regards, > >>>> Antonio > >>>> CT1TE > >>>> > >>>> Quoting Chuck Harris <[email protected]>: > >>>> > >>>> Are you sure that your Loran chain is still up? In the US and > >>>>> Canada, Loran has been decommissioned. > >>>>> > >>>> > >>> _______________________________________________ > >>> time-nuts mailing list -- [email protected] > >>> To unsubscribe, go to > >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > >>> and follow the instructions there. > >>> > >> _______________________________________________ > >> time-nuts mailing list -- [email protected] > >> To unsubscribe, go to > >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > >> and follow the instructions there. > >> > > > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
