I stand corrected. My 5089 definitely uses the same connector as the 5061A.
However, my 5085 uses a smaller connector, a DMS3106A10SL-3S. http://www.galco.com/buy/DDK/DMS3106A10SL-3S It uses a smaller clamp and strain relief, a DMS3057-4A, though I had to remove the strain relief due to the size of the cable I used to connect to 120 VAC. http://www.galco.com/buy/DDK/DMS3057-4A Sorry for the misleading info, but, perhaps, there are two different connectors for the 5085, depending on age/serial number of the equipment. Joe -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of J. L. Trantham Sent: Saturday, November 24, 2012 9:36 PM To: 'Discussion of precise time and frequency measurement' Subject: Re: [time-nuts] 5061A AC Power connector Paul, According to the 5089 manual, the power connector is the same. Both the 5085 and 5089 call for the same HP part number for the AC power cord. Therefore, I suspect they are the same. I have a 5085 hooked up and I can make sure tomorrow if you need it. Joe -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of paul swed Sent: Saturday, November 24, 2012 9:06 PM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] 5061A AC Power connector I hoped it helped also. I know it did for me. Will order 2 sets so I can finally have real connectors on the 5061 and 5065. I wonder if its the same for the standby power supply may need to order 3. Regards Paul WB8TSL On Sat, Nov 24, 2012 at 9:35 PM, J. L. Trantham <[email protected]> wrote: > Pete, > > In the US, Galco sells a DDK product that works well. The connector > and shell are a DMS3106A18-22S. > > http://www.galco.com/buy/DDK/DMS3106A18-22S > > You will also need a clamp and strain relief. I use a DMS3057-10A. > > http://www.galco.com/buy/DDK/DMS3057-10A > > It is the same connector as a 5065A though you have to be careful > about the wiring. Some of the 5065A's are the same as the 5061A and > others are different. > > Hope this helps. > > Joe > > -----Original Message----- > From: [email protected] [mailto:[email protected]] > On Behalf Of Pete Lancashire > Sent: Saturday, November 24, 2012 6:51 PM > To: Discussion of precise time and frequency measurement > Subject: [time-nuts] 5061A AC Power connector > > What is the MS type for the power plug for a 5061A ? > > I could not find it in the PDF I have. > > -pete > > _______________________________________________ > time-nuts mailing list -- [email protected] To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
