Hi Tom,
You don't enter the comma or the space they just show up in the list
that way after you enter them.
While I don't use a transverter for 23 centimeters I made the entries as
follows to test the function.
Band 23cm
Offset -1268.000000
Then added to the upper list as follows:
Region 2 or ALL (tried both)
Mode FT8
Frequency 1296.174000
Clicked OK at the needed places and it works fine, when I select 23cm
from the band pull down list my Icom IC-7300 went to 28.174.000 just as
it should.
My rig control is passing through Ham Radio Deluxe. If you are
controlling the rig directly it might be an error in Hamlib or something
else. I am running V2.6.1 of WSJT-X.
Hope this helps.
73 Harry (KA2ENE)
------------------------------------------------
On 7/18/2023 4:23 PM, tom via wsjt-devel wrote:
Thanks all.
Yes I was following all comments - I have no issue at all with 2m or
70cms offsets - same version of Windows, same rig (TS680) same copy of
WSJT. Yes saving all settings with the OK.
Yes was entering -1268 as offset - one thing - could someone confirm the
format of the offset on your working system. Here it is -1,268.000 000
Mhz - note the comma as the separator on 1,268
Harry your example had no comma. Could it be the locale I have set to UK ?
Thanks
Tom
Tom GM8MJV
t...@tkrh.co.uk <mailto:t...@tkrh.co.uk>
On 18 Jul 2023, at 17:37, Harry E. Hoffman via wsjt-devel
<wsjt-devel@lists.sourceforge.net
<mailto:wsjt-devel@lists.sourceforge.net>> wrote:
Hi Tom,
Appending my post:
The offset frequency is a negative number so it should read:
Band = 23 cm
Offset = -1268.000 000 (note the decimal point and the space)
I am using an IC-7300 as the IF radio on my system and my transverter
settings for 1.25 meters and 33 centimeters work fine. I don't use a
transverter for 23 centimeters as I also have an IC-9700.
73 Harry (KA2ENE)
-----------------------------------
On 7/18/2023 10:18 AM, Harry E. Hoffman via wsjt-devel wrote:
Hi Tom,
I use transverters for 1.25 meters and 33 centimeters, using the the
same idea try this for 23 centimeters.
Band = 23 cm
Offset = 1268.000 000 (note the decimal point and the space)
Check the frequency list and if there are no entries for 23 cm add
them for the modes you want.
Example: Region 2 FT8 1296.174 000
good luck.
73 Harry (KA2ENE)
-----------------------------------
On 7/18/2023 6:30 AM, tom via wsjt-devel wrote:
Hi - posted on main list but no final solution.
Windows 11, wsjt-X 2.6.2 and 2.7.0-rc2
Setting up a 23cms Transverter with a 28 MHz IF - seems to be an
issue. Used an offset -1268 and wsjt-x displayed 23cms ok but cat
jumped rig to 1.065 MHz.
Tried the example given on archive for 2m offset -116 and all worked
fine, cat kicked in and rig (TS680) switched to 28 Mhz and WSJT-X
displayed 144 MHz.
Could it be the , in offset freq -1268 is entered and software
formats it to -1,268.000 000 MHz.
Tried the same setup with MSHV and WSJT-X-Improved and worked as
expected with -1268 offset. Cat and freq both ok.
Thanks in advance for any suggestions but it does look like a bug
rather than user error.
Tom GM8MJV
t...@tkrh.co.uk <mailto:t...@tkrh.co.uk> <mailto:t...@tkrh.co.uk
<mailto:t...@tkrh.co.uk>>
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
<mailto:wsjt-devel@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
<mailto:wsjt-devel@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net <mailto:wsjt-devel@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
