Hi Tom I enter the offset as a number with no commas or decimal point. In the station information table it then appears with comma separator and decimal points
[image: image.png] This is on a UK purchased PC, running 2.7.0-rc2 73 Charlie DL3WDG On Tue, 18 Jul 2023 at 22:45, tom via wsjt-devel < wsjt-devel@lists.sourceforge.net> wrote: > Thanks all. > > Yes I was following all comments - I have no issue at all with 2m or 70cms > offsets - same version of Windows, same rig (TS680) same copy of WSJT. Yes > saving all settings with the OK. > > Yes was entering -1268 as offset - one thing - could someone confirm the > format of the offset on your working system. Here it is -1,268.000 000 Mhz > - note the comma as the separator on 1,268 > > Harry your example had no comma. Could it be the locale I have set to UK ? > > > Thanks > > Tom > > > > Tom GM8MJV > t...@tkrh.co.uk > > > > > > On 18 Jul 2023, at 17:37, Harry E. Hoffman via wsjt-devel < > wsjt-devel@lists.sourceforge.net> wrote: > > Hi Tom, > > Appending my post: > > The offset frequency is a negative number so it should read: > > Band = 23 cm > Offset = -1268.000 000 (note the decimal point and the space) > > I am using an IC-7300 as the IF radio on my system and my transverter > settings for 1.25 meters and 33 centimeters work fine. I don't use a > transverter for 23 centimeters as I also have an IC-9700. > > 73 Harry (KA2ENE) > > ----------------------------------- > > On 7/18/2023 10:18 AM, Harry E. Hoffman via wsjt-devel wrote: > > Hi Tom, > I use transverters for 1.25 meters and 33 centimeters, using the the same > idea try this for 23 centimeters. > Band = 23 cm > Offset = 1268.000 000 (note the decimal point and the space) > Check the frequency list and if there are no entries for 23 cm add them > for the modes you want. > Example: Region 2 FT8 1296.174 000 > good luck. > 73 Harry (KA2ENE) > ----------------------------------- > On 7/18/2023 6:30 AM, tom via wsjt-devel wrote: > > Hi - posted on main list but no final solution. > > Windows 11, wsjt-X 2.6.2 and 2.7.0-rc2 > > Setting up a 23cms Transverter with a 28 MHz IF - seems to be an issue. > Used an offset -1268 and wsjt-x displayed 23cms ok but cat jumped rig to > 1.065 MHz. > > > Tried the example given on archive for 2m offset -116 and all worked fine, > cat kicked in and rig (TS680) switched to 28 Mhz and WSJT-X displayed 144 > MHz. > > Could it be the , in offset freq -1268 is entered and software formats it > to -1,268.000 000 MHz. > > Tried the same setup with MSHV and WSJT-X-Improved and worked as expected > with -1268 offset. Cat and freq both ok. > > Thanks in advance for any suggestions but it does look like a bug rather > than user error. > > Tom GM8MJV > t...@tkrh.co.uk <mailto:t...@tkrh.co.uk <t...@tkrh.co.uk>> > > > > > > > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > > > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel >
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
