True... I was thinking along the lines of, might as well use all four if you can.
On Tue, Aug 16, 2016 at 7:01 PM, George Skorup <geo...@cbcast.com> wrote: > Nah, the 35W should be fine. That radio is probably not going to use more > than 20W. And yes, it's only two pairs, but Cambium said that's fine. In > fact, that's exactly what you get when running on a CMM4 (in 48/56v mode, > then you have to flip pins 5 & 7 because of the stupid 320/430 pinout). > > On 8/16/2016 6:49 PM, Mathew Howard wrote: > > I would use the 48VH (assuming we're still talking about the 450i AP) > power on all 4 pairs is what they want, and they don't care about polarity. > > On Tue, Aug 16, 2016 at 6:47 PM, Josh Luthman <j...@imaginenetworksllc.com > > wrote: > >> I know the H has power on all pins so I'd suggest looking in the forum >> before plugging it in. >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> >> On Aug 16, 2016 7:40 PM, "Darin Steffl" <darin.ste...@mnwifi.com> wrote: >> >>> So should I use regular 48V (0.75A) or 48VH (1.5A) for Netonix powering >>> 450i AP 900mhz? >>> >>> >>> >>> On Tue, Aug 16, 2016 at 5:43 PM, CBB - Jay Fuller < >>> par...@cyberbroadband.net> wrote: >>> >>>> >>>> i keep trying to preach that. >>>> i know we have one site with two sync sources >>>> no apparent problems tho >>>> >>>> >>>> ----- Original Message ----- >>>> *From:* Josh Luthman <j...@imaginenetworksllc.com> >>>> *To:* af@afmug.com >>>> *Sent:* Tuesday, August 16, 2016 4:23 PM >>>> *Subject:* Re: [AFMUG] PMP450i 900mhz and Netonix >>>> >>>> It's proper to have one sync source at the site anyway. >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> On Aug 16, 2016 5:14 PM, "Kurt Fankhauser" <lists.wavel...@gmail.com> >>>> wrote: >>>> >>>>> it would be better if it (450i) had on-board sync so i can power the >>>>> whole tower with one Netonix Switch and be done, but no i gotta mess >>>>> around >>>>> with a CTM2 or Packet Flux Sync Injector now to get timing on 450i >>>>> >>>>> On Tue, Aug 16, 2016 at 3:23 PM, George Skorup <geo...@cbcast.com> >>>>> wrote: >>>>> >>>>>> As others have said, you obviously won't get sync from the Netonix. >>>>>> Plug the 450i *AP* in and go. It is 802.3at compliant, but it will also >>>>>> take passive injected power without issue. And you don't need to change >>>>>> any >>>>>> wires around. It will take either polarity on any pair. Cambium actually >>>>>> did this right. Woulda been even better if they designed for 20-60vdc, >>>>>> but >>>>>> I guess you can never have it all. >>>>>> >>>>>> Out of the 450i series, the only radio that is not 802.3at is the 900 >>>>>> SM which is the old Canopy 29.5v like FSK and regular 450. >>>>>> >>>>>> On 8/16/2016 12:18 PM, Darin Steffl wrote: >>>>>> >>>>>> Hello all, >>>>>> >>>>>> Will a Netonix 48V switch power the PMP450i 900mhz? >>>>>> >>>>>> I'm leaning towards that it will NOT due to needing 48-56V and >>>>>> 802.3at PoE which I don't think Netonix supports. >>>>>> >>>>>> Can anyone confirm my thoughts or tell me I'm wrong and it will work? >>>>>> >>>>>> Thanks >>>>>> >>>>>> -- >>>>>> Darin Steffl >>>>>> Minnesota WiFi >>>>>> www.mnwifi.com >>>>>> 507-634-WiFi >>>>>> <http://www.facebook.com/minnesotawifi> Like us on Facebook >>>>>> <http://www.facebook.com/minnesotawifi> >>>>>> >>>>>> >>>>>> >>>>> >>> >>> >>> -- >>> Darin Steffl >>> Minnesota WiFi >>> www.mnwifi.com >>> 507-634-WiFi >>> <http://www.facebook.com/minnesotawifi> Like us on Facebook >>> <http://www.facebook.com/minnesotawifi> >>> >> > >