It's hard to tell. You could probably solder a wire to jump it but you still need to find out what caused it to burn.
On Thu, May 19, 2016 at 6:01 PM, Eric S <[email protected]> wrote: > > <https://lh3.googleusercontent.com/-Y-YUZng17Kg/Vz43wuCQSOI/AAAAAAAAAFM/XZa8wNkO8AwCxANqqVZU3sHQL_MLv-_gQCLcB/s1600/image1.JPG> > Well, I went out and took another look at the control board today. and I > found this. Looks burnt > > On Thursday, May 19, 2016 at 2:46:13 PM UTC-5, Eric S wrote: >> >> no, but I might have to try that. >> >> On Thursday, May 19, 2016 at 1:26:15 PM UTC-5, bmacpiper wrote: >>> >>> Have you called Todd/WLL? He might have a way of testing the Giemme. I >>> still think it might be covered if bad; six months is way too short for a >>> life span on that part. >>> >>> Sent from my apple IIe >>> >>> On May 19, 2016, at 11:18, Eric S <[email protected]> wrote: >>> >>> The first relay with one large contact closes when the machine turns on, >>> opens back up when the machine goes off, but I can't see anything happening >>> with the second relay. >>> >>> On Thursday, May 19, 2016 at 12:47:30 PM UTC-5, bmacpiper wrote: >>>> >>>> Perhaps look through the blue clear box inside at the two relays--mine >>>> had browned the plastic a bit but was barely noticeable. >>>> b >>>> >>>> Sent from my apple IIe >>>> >>>> On May 19, 2016, at 10:43, Eric S <[email protected]> wrote: >>>> >>>> I took the cover off the giemme box this morning, and didn't see >>>> anything obvious. I had a blown transformer on my last machine, but this >>>> one doesn't look burnt like that one did. >>>> >>>> When I turn the machine on there is a click, but its in the AKO >>>> controller, not the giemme box. Is that what you are talking about? >>>> >>>> On Thursday, May 19, 2016 at 11:39:14 AM UTC-5, Ira wrote: >>>>> >>>>> Hello Eric, >>>>> >>>>> Wednesday, May 18, 2016, 3:45:34 PM, you wrote: >>>>> >>>>> >>>>> The pump works to fill the boilers, which I understand is its first >>>>> job. but once the boilers are full it switches power to the pressure stat. >>>>> to turn on the heaters. The white wire at the top of the pressure stat, >>>>> I >>>>> guess should be the power in. There is no power there. I chased that >>>>> wire >>>>> back to the terminal in the giemme box that says resistenza. >>>>> >>>>> >>>>> Well, sounds like it's time to look inside the Gimme box and see if >>>>> you can see something wrong. When you power the machine on, does the box >>>>> click a bit later, few seconds max? If the box clicks, the pressurestat >>>>> should get power. >>>>> >>>>> -- Ira >>>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "Brewtus" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To post to this group, send email to [email protected]. >>>> Visit this group at https://groups.google.com/group/brewtus. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Brewtus" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To post to this group, send email to [email protected]. >>> Visit this group at https://groups.google.com/group/brewtus. >>> For more options, visit https://groups.google.com/d/optout. >>> >>> -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at https://groups.google.com/group/brewtus. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Brewtus" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at https://groups.google.com/group/brewtus. For more options, visit https://groups.google.com/d/optout.
