Once I had the screws out, the hatch frames just lifted off. They were not held on *at all* by goo.
Jim Watts Paradigm Shift C&C 35 Mk III Victoria, BC On Tue, 5 May 2020 at 19:28, Graham Collins via CnC-List < cnc-list@cnc-list.com> wrote: > Hi Matt > > They do come in a version openable from the outside, scroll down and look > at "double opening". > > Getting a hatch rim off the deck is no biggie, unless someone used 5200 > putting it on. With the butyl tape that was used on C&Cs it is pretty easy > - remove all screws, and start at a corner where you can get some prying > action on it, see if you can lift it at all, get a putty knife in. Work > your way up from there. Might take an hour but no heroic measures are > needed. > > Graham Collins > Secret Plans > C&C 35-III #11 > > On 2020-05-05 12:30 a.m., Matthew Schlanger via CnC-List wrote: > > I was liking the idea of Lewmar. > > And I think the low profiles look great but I don’t see access from top > side which the fore-deck guys likes to have to get spinnakers in and out > easily without having to go below. > > When you say easy drop in on Lewmars, I assume I would need to rip out and > replace the frame that attaches to the deck. I was thinking of trying to > just change out the hatch first. A friend told me of his troubles trying to > get the frame off the deck. If it’s a direct replacement the hinges would > match? I don’t think I can do that with a Lewmar based on the diagrams I > saw. My issue is the hatch itself, I suspect no water is coming in from the > bottom frame. > > I have a couple of emails into Atkins and Hoyle though I have not heard > back yet. I’ll keep on them. > > Again thanks to all. The collective wisdom is amazing. > > M > > On Apr 28, 2020, at 2:19 PM, Jim Watts via CnC-List <cnc-list@cnc-list.com> > wrote: > > I replaced all the hatches on the boat with Lewmars. Saloon hatch and > forward hatch were drop-in replacements, the head hatch took a bit of glass > work but works fine. > > Jim Watts > Paradigm Shift > C&C 35 Mk III > Victoria, BC > > > On Mon, 27 Apr 2020 at 06:15, Paul Fountain via CnC-List < > cnc-list@cnc-list.com> wrote: > >> Our 77 C&C27-3 had an Aitkens&Hoyle hatch, much better than the Bomar >> hatches on our 85 33-ll, which have been replaced with Lewmar Ocean series >> hatches. The angle of the forward hatch made the low profile hatches >> impractical, and the raised Fiberglas either side made them unattractive. >> >> I’d rate the A&H and Lewmar Ocean series comparable . >> >> Paul >> ------------------------------ >> *From:* CnC-List <cnc-list-boun...@cnc-list.com> on behalf of Bill >> Coleman via CnC-List <cnc-list@cnc-list.com> >> *Sent:* Monday, April 27, 2020 8:33:21 AM >> *To:* cnc-list@cnc-list.com <cnc-list@cnc-list.com> >> *Cc:* Bill Coleman <colt...@gmail.com> >> *Subject:* Re: Stus-List Need to replace forward hatch on 35 mkIII >> >> >> That is a handsome looking hatch. >> >> How do you compare the overall quality compared to Atkins & Hoyle or >> Lewmar? >> >> >> Bill Coleman >> >> >> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Graham >> Collins via CnC-List >> *Sent:* Sunday, April 26, 2020 9:27 PM >> *To:* cnc-list@cnc-list.com >> *Cc:* Graham Collins >> *Subject:* Re: Stus-List Need to replace forward hatch on 35 mkIII >> >> >> Hi Matthew >> >> Atkins & Hoyle make the direct replacement, but there is an alternative - >> I put on a low profile stainless hatch from these guys. >> http://www.manshipmarine.com/low-profile-deck-hatch.html >> >> <http://www.manshipmarine.com/low-profile-deck-hatch.html> >> >> I'll look to see if I have any pics. >> >> Graham Collins >> >> Secret Plans >> >> C&C 35-III #11 >> >> On 2020-04-26 10:12 p.m., Matthew Schlanger via CnC-List wrote: >> >> Hello CnC list, >> >> >> >> I was wondering if anyone knew exactly what kind and where I can find a >> replacement for my forward hatch on a 1983 C&C 35 mkIII. >> >> >> >> I am hoping I can just get a new hatch and use the existing frame, though I >> assume it comes with a new frame as well just in case. >> >> >> >> I measured the outer dimensions of the flanges on the frame at 20 7/8” >> square, the outer dimensions of the hatch at ~21 13/16 square, and the inner >> distance between the hinges on the hatch at 14 1/16”. >> >> >> >> I thought this would use a Lewmar replacement but the dimensions don’t seem >> to match. >> >> >> >> Thanks in advance. >> >> This list is great, I wish I had more time to read it. >> >> >> >> Matthew Schlanger >> >> The Office >> >> 1983 C&C 35 mkIII >> >> Nyack NY >> >> _______________________________________________ >> >> >> >> Thanks everyone for supporting this list with your contributions. Each and >> every one is greatly appreciated. If you want to support the list - use >> PayPal to send contribution -- https://www.paypal.me/stumurray >> >> >> >> _______________________________________________ >> >> Thanks everyone for supporting this list with your contributions. Each >> and every one is greatly appreciated. If you want to support the list - >> use PayPal to send contribution -- https://www.paypal.me/stumurray >> >> _______________________________________________ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > > > _______________________________________________ > > Thanks everyone for supporting this list with your contributions. Each and > every one is greatly appreciated. If you want to support the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray > > _______________________________________________ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > >
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray