Actually right, I have not connected to serial debug port yet. pin_d2 led is connected but not blinking while pinging. I also removed the line : network_set_remote_ip(192,168,1,10) ,but this time I can not see any response from 192.168.1.60 on wireshark. (before removing that line I was able to see ICMP responses from 192.168.1.60 to 192.168.1.10) I'll connect to serial and inform you a.s.a.p
Kutsal On 17 Ocak, 22:06, mattschinkel <[email protected]> wrote: > Seb is right, typo > > It sounds like you don't have a serial port connected, which is > important for debugging. > > If you connect a serial port, you will see something like this: > > sent arp > request > sent arp > request > sent arp > request > arp reply > recieved! > arp reply > recieved! > arp reply recieved! > > You should also see a LED blink on pin ping_d2 when sending ping via > windows CMD screen. > > Matt. > > On Jan 17, 2:01 pm, Sebastien Lelong <[email protected]> > wrote: > > > > > > > > > Hi Kutsal, > > > If you're using latest version (rev. 2434), edit icmp.jal and remove the > > line 108: > > > network_set_remote_ip(192,168,1,10) > > > in procedure icmp_send_echo_reply. I guess this is a typo ! > > > Cheers > > Seb > > > 2011/1/17 kbaser <[email protected]> > > > > Hi Matt, > > > I just checked the module with 10k pull up's on pin_d0 & pin_d1. > > > Unfortunately I got no response on windows cmd screen. > > > But I capture some events on WireShark ; > > > The pic recognized as AsustekC_c6:53:16 > > > It broadcasts on power-up with ARP 8 times > > > It replies to ping requests from my PC(192.168.1.11), but it replies > > > to 192.168.1.10 (which is not available on the network) with ICMP. > > > Please send your comments, thank you > > > > Kutsal > > > > On Jan 16, 8:44 pm, mattschinkel <[email protected]> wrote: > > > > > I didn't connect the > > > > > buttons on pin_d1 and pin_d0, but I think they have no effect on > > > > > incoming ping requests, right? > > > > > Actually this may affect your sample. Please at least put pull-up > > > > resistors on pin_d1 and pin_d0. > > > > > In the main loop, there is this, which could cause it to get stuck: > > > > > while button == LOW loop > > > > _usec_delay(100_000) > > > > end loop > > > > > The sample is tested and works, It looks like you have the same > > > > module. You could also try installing Wireshark to see if you get any > > > > data from 192.168.1.60 > > > > > Also check that your network IP addresses are 192.168.1.xxx > > > > > Try that first, if you still have trouble I can give you more > > > > troubleshooting info. > > > > > Matt. > > > > -- > > > You received this message because you are subscribed to the Google Groups > > > "jallib" group. > > > To post to this group, send email to [email protected]. > > > To unsubscribe from this group, send email to > > > [email protected]<jallib%[email protected]> > > > . > > > For more options, visit this group at > > >http://groups.google.com/group/jallib?hl=en. -- You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/jallib?hl=en.
