I do not have a target oil temp at this point (from my last oil cooler setup
on another car... i don't even remember my aims then).  Mainly this is a
desire to just not cook my oil and keep everything running.  Heck, my entire
v-mount system was built as preventative maintenance.

The "right behind the middle of bumper" idea is kind of leading me now.  We
still have to put in a tubular bumper bar... and I could mount it off that.
It'll heat the air going to rad/ic some... but i can't see it doing that
much harm.

-Dave

On Mon, May 12, 2008 at 12:56 PM, Rob Ebersol <[EMAIL PROTECTED]> wrote:

>
> I'm going to say yes. Based on the fact that I know of more than one turbo
> Miata tracked for multiple seasons with only the stock oil cooler in place.
>
> The one thing that rx oil cooler has going for it is capacity. I believe
> with lines and cooler you're going to get a full quart increase in your
> oiling system. That's HUGE. Then consider that at any moment you'll have
> about 3/4 quart sitting in the cooler. Will it receive air flow passed on
> from the radiator?
>
> I'm also assuming you are aiming for oil temps around 220f on track...
>
> rob
>
>
>
> On May 12, 2008, at 1:07 PM, Dave Ott wrote:
>
>  So I've been building up my track 'toy'.  It has a V-mount setup for the
> > radiator and the intercooler.  I did this to allow cool air to both systems
> > at all times, as this car is being built for track use.
> >
> > I'm finally ready to start debugging and setting the car up for autox
> > (testing) and then its new home on the track.  I hadn't finished my oil
> > cooler setup when doing all the fabrication and recent chats have got me
> > thinking about getting it finished sooner than later.
> >
> > Oil cooler is an FD Rx7 oem unit.  It will use a Mocal Oil adapter with
> > thermostat.
> >
> > My current plan is to place it parallel with the radiator, just under
> > the radiator fans.
> > front view of V:
> > http://i295.photobucket.com/albums/mm133/splitime/Miata%20build%
> > 20pictures/IMG_0490.jpg
> > side view
> > http://i295.photobucket.com/albums/mm133/splitime/Miata%20build%
> > 20pictures/IMG_0502.jpg
> > Here is a temporary bracket made to suspend the oil cooler during
> > earlier brainstorming... (this is the planned location)
> > http://i295.photobucket.com/albums/mm133/splitime/Miata%20build%
> > 20pictures/IMG_0521.jpg
> > http://i295.photobucket.com/albums/mm133/splitime/Miata%20build%
> > 20pictures/IMG_0522.jpg
> >
> > Is that sufficient?
> > The IC/rad area is ducted on the sides and will be fully sealed off once
> > I finish the rest of the ducting.  All air into opening of bumper, will go
> > through radiator or intercooler.
> >
> > I'm open to all thoughts ideas... ideally I want to use the current
> > cooler... since I have it... but please feel free to think outside the box.
> >
> > I had also considered opening up the front bumper even more... hole saw
> > in the remaining area up front... across middle... and putting the oil
> > cooler right in the middle there. (now that I think about that one... I
> > kinda like it again... hurm....)
> > front bumper view, picture holes right below the bumper line:
> > http://i295.photobucket.com/albums/mm133/splitime/Miata%20build%
> > 20pictures/IMG_0130.jpg
> >
> > -Dave
> > _______________________________________________
> > Miatapower mailing list
> > [email protected]
> > http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
> >
>
>
_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

Reply via email to