True enough Ed. I think a nice thing to do would be to change the
function of the PlacementTools Icon (in the floating menu) to be
'interactive routing' instead of placing lines. They are almost the same
thing except for the net association that occurs with interactive
routing lines.



> -----Original Message-----
> From: Shane Edwards [mailto:[EMAIL PROTECTED]] 
> Sent: Thursday, September 12, 2002 3:31 PM
> To: 'Protel EDA Forum'
> Subject: Re: [PEDA] - Possible Bug? -NO
> 
> 
> Well it is either a bug or a feature. And if it's a feature 
> what do you use it for? If people are using it or it helps 
> them then I'd like to know :-)
> 
> I say it should know what layer you are on, so if you are 
> placing a mech line protel can say 'Hey, they're on a mech 
> layer, I'll bring up a non-electrical edit window when they 
> hit tab'. Instead of 'Hey, I'm sure they intended to place 
> copper even though they haven't started from an electrical 
> hotpoint. Let me just kindly switch them to a Cu layer'
> 
> As to the schematic commands I was indicating that there are 
> place graphical line and place electrical line ICONs. 
> Now the line containing the electrical connectivity is the 
> same ICON used to place non-electrical lines (mech) in PCB. I 
> would call this a slight inconsistency within a single 
> program. Sure it's easy to assign a different bmp to the 
> command but it's the default setup.
> 
> Ed
> 
> -----Original Message-----
> From: Dennis Saputelli [mailto:[EMAIL PROTECTED]]
> Sent: Friday, 13 September 2002 4:13 a.m.
> To: Protel EDA Forum
> Subject: Re: [PEDA] - Possible Bug? -NO
> 
> 
> no i don't agree that this is a bug
> when you say "shouldn't it know when it's placing a mech 
> line?"  i don't see how
> 
> you could wish to place a line on a copper layer (which would 
> of course be conductive)
> 
> for example on top layer if you start from a pad with a net and  P T 
> the track will have the associated net
> 
> if instead you did P L you would see NO NET as the track 
> attribute and the width would be independent of the rules set 
> and follow the last line width used
> 
> also even on a copper layer the two commands are useful for 
> keeping the separate widths per type
> 
> as to the schematic commands
> in the schematic editor 
> a wire is P W
> a line is P D L  (not P L as you indicated)
> 
> but in the sch lib editor a line is P L since everything is a 
> "D"rawing primitive and there are no wires
> 
> Dennis Saputelli
> 
> Shane Edwards wrote:
> > 
> > Yes PL is the correct comand.
> > Ever notice how the place electrical wire in schematic icon is the 
> > same as the place line icon in PCB! This helps with my confusion :-)
> > Shouldn't Protel know when it's placing a mechanical line, 
> that to me is a
> > bug!
> > 
> > Ed
> > 
> > -----Original Message-----
> > From: Dennis Saputelli [mailto:[EMAIL PROTECTED]]
> > Sent: Thursday, 12 September 2002 12:59 p.m.
> > To: Protel EDA Forum
> > Subject: Re: [PEDA] - Possible Bug? -NO
> > 
> > this is not a bug
> > you are just using the wrong command
> > 
> > use P L
> > place line for mech layers
> > 
> > when you hit TAB a different dialog will pop and it won't swap you 
> > back to a copper layer
> > 
> > P T is for electrical tracks
> > 
> > if you think about it, it is not bad
> > also the last used width will stick for each type which is nice
> > 
> > Dennis Saputelli
> > 
> > Shane Edwards wrote:
> > >
> > > Hey Rob,
> > > I presume it's because there is no non-copper layers in the drop 
> > > down
> box
> > in
> > > the interactive routing window, so it then automatically 
> changes you 
> > > to
> > the
> > > first cu layer... top!
> > > Annoys the hell out of me too, and unfortunately is not a 
> new fault 
> > > so
> > don't
> > > expect a fix!
> > >
> > > Ed
> > >
> > > -----Original Message-----
> > > From: Rob Young [mailto:[EMAIL PROTECTED]]
> > > Sent: Thursday, 12 September 2002 5:02 a.m.
> > > To: Protel EDA Forum
> > > Subject: [PEDA] Possible Bug?
> > >
> > > I am wondering if any of you can replicate this:
> > >
> > > Start placing a series of track segments on Mech 1.
> > > While in the process of placing track, hit the "TAB" key 
> to change 
> > > the
> > track
> > > width on the fly.
> > > Upon changing the width and closing the track dialog box, 
> you are no
> > longer
> > > placing track on Mech 1 but on the Top signal layer.
> > >
> > > A little annoying, but something that I have worked around for 
> > > awhile
> now.
> > >
> > > Can anyone confirm that this is repeatable in DXP as well?
> > >
> > > Rob
> > >
> > 
> > 
> **********************************************************************
> > **
> > * Tracking #: 20317CE6AC25EA46AA411E7DC3AA767AAA784DD7
> > *
> > 
> **************************************************************
> **********
> > --
> >
> ______________________________________________________________
> _____________
> > www.integratedcontrolsinc.com            Integrated Controls, Inc.
> >    tel: 415-647-0480                        2851 21st Street
> >       fax: 415-647-3003                        San 
> Francisco, CA 94110
> 
> -- 
> ______________________________________________________________
> _____________
> www.integratedcontrolsinc.com            Integrated Controls, Inc.    
>    tel: 415-647-0480                        2851 21st Street          
>       fax: 415-647-3003                        San Francisco, CA 94110
> 

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/proteledaforum@techservinc.com
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to