Mr. Lyons,
Thanks for the advice. No, it is a double sided pth.
Regards
Ken
-Original Message-
From: Pat Lyons [mailto:[EMAIL PROTECTED]]
Sent: Friday, June 07, 2002 7:59 PM
To: Protel EDA Forum
Subject: Re: [PEDA] help, how do i make rectangular holes in components
and on the pcb
i *did* put the smiley face :)
Dennis Saputelli
Ian Wilson wrote:
>
> On 01:58 PM 8/06/2002 -0700, Dennis Saputelli said:
> >boy that's a great point pat
> >
> >i do them on doubles a lot but might have blown it on multi if it ever
> >came up
> >
> >of course a board shop would never let that g
On 01:58 PM 8/06/2002 -0700, Dennis Saputelli said:
>boy that's a great point pat
>
>i do them on doubles a lot but might have blown it on multi if it ever
>came up
>
>of course a board shop would never let that get out would they ? :)
Wanna bet? On an early board I did (years ago) I forgot to p
boy that's a great point pat
i do them on doubles a lot but might have blown it on multi if it ever
came up
of course a board shop would never let that get out would they ? :)
Dennis Saputelli
Pat Lyons wrote:
>
> On Fri, 07 Jun 2002 10:29:42 -0400, Ken Henrich wrote:
> >Hi
> >
> >I want to
On Fri, 07 Jun 2002 10:29:42 -0400, Ken Henrich wrote:
>Hi
>
>I want to make rectangular holes in pads for components with metal
>tabs. For
>instance, a hole 40mils by 120 mils. Can this be done in Protel
>99SE? BTW,
>is hole the proper nomeclature for this?
>
>thanks and regards
>Ken
You didn't
bject: Re: [PEDA] help, how do i make rectangular holes in components
and on the pcb itself?
Hello Ken,
Friday, June 7, 2002, 7:29:42 AM, you wrote:
> Hi
> I want to make rectangular holes in pads for components with metal tabs.
For
> instance, a hole 40mils by 120 mils. Can this be
> I want to make rectangular holes in pads for components with metal tabs. For
> instance, a hole 40mils by 120 mils. Can this be done in Protel 99SE? BTW,
> is hole the proper nomeclature for this?
I've done this in the past by placing the appropriate track on the drill drawing
layer, then add
The best way to do this is to call your fab and ask them how they want the
information provided.
A slot, or rectangular hole, is done at the fab by using a routing bit -
usually after the board is complete, but before finish plating and
masking. Your fab will have its own procedures and desir
Hello Ken,
Friday, June 7, 2002, 7:29:42 AM, you wrote:
> Hi
> I want to make rectangular holes in pads for components with metal tabs. For
> instance, a hole 40mils by 120 mils. Can this be done in Protel 99SE? BTW,
> is hole the proper nomeclature for this?
> thanks and regards
> Ken
Unfort
Ken, I've done this by creating cutouts of the proper size (tiny)
using say four 1mil holes on 5mil pads. I included on the Drill Drawing
a detail showing routing a rectangular cutout from these sets of
1mil holes. You _must specify_ "Plate Through" for all these special
cutouts. Note that you wo
Hi
I want to make rectangular holes in pads for components with metal tabs. For
instance, a hole 40mils by 120 mils. Can this be done in Protel 99SE? BTW,
is hole the proper nomeclature for this?
thanks and regards
Ken
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a mes
11 matches
Mail list logo