, K4TAX
On 6/29/2022 10:29 AM, elecraft-requ...@mailman.qth.net wrote:
Message: 4
Date: Mon, 27 Jun 2022 21:34:05 -0400
From: "Robert Ward"
To:
Subject: [Elecraft] K3 data mode not working on 6 meter band NQ3N
Message-ID: <000c01d88a8f$28e21050$7aa630f0$@com>
Content-Type: text/plai
Hi
My K3 will not display FT8 signals on 6 meters when set to
data mode. Data mode works on 10 thru 160 but not on 6 meters, FT8 decodes
fine when USB is selected.
Any suggestions would be appreciated!
Thanks, Bob NQ3N
--
This email has been checked for viruses by
> Audio is being fed from my PC to the K3's line input and I'm certain
> that the radio is in DATA A and the Config for MIC SEL is set to LInE
> In.
It *sounds like* you are still in AFSK A and not DATA A. By default
AFSK A has a narrow audio filter on the input of the modulator process
(DSP)
I worked the RTTY contest yesterday using AFSK with N1MM. All worked
fine and I shut everything down when I was done. Today I tried to
operate FT8 but I can not get any power output.
Audio is being fed from my PC to the K3's line input and I'm certain
that the radio is in DATA A and the
anks for asking.
>
> From: Nr4c
> Sent: Friday, June 26, 2020 11:35 AM
> To: John McBride
> Cc: elecraft@mailman.qth.net ;
> donw...@embarqmail.com
> Subject: Re: [Elecraft] K3 DATA setting
>
> Does your software have anything to do with this?
>
> Sent from my
To: John McBride
> Cc: elecraft@mailman.qth.net ;
> donw...@embarqmail.com
> Subject: Re: [Elecraft] K3 DATA setting
>
> Does your software have anything to do with this?
>
> Sent from my iPhone
> ...nr4c. bill
>
>
>> On Jun 26, 2020, at 11:43 AM, John McBr
No, it does not but thanks for asking.
From: Nr4c
Sent: Friday, June 26, 2020 11:35 AM
To: John McBride
Cc: elecraft@mailman.qth.net ; donw...@embarqmail.com
Subject: Re: [Elecraft] K3 DATA setting
Does your software have anything to do with this?
Sent from
PM
> To: John McBride ; elecraft@mailman.qth.net
>
> Subject: Re: [Elecraft] K3 DATA setting
>
> John,
>
> Mode is a per band setting. So do not expect it to be 'sticky' from
> band to band.
> Once you go to the band for operation, you should be able to change the
> mode
.
John
From: Don Wilhelm
Sent: Thursday, June 25, 2020 6:47 PM
To: John McBride ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 DATA setting
John,
Mode is a per band setting. So do not expect it to be 'sticky' from
band to band.
Once you go to the band
John,
Mode is a per band setting. So do not expect it to be 'sticky' from
band to band.
Once you go to the band for operation, you should be able to change the
mode.
73,
Don W3FPR
On 6/25/2020 6:14 PM, John McBride wrote:
I am getting my K3 ready to use PSK31 on Field Day. 40 meters is
Make sure you aren't in Split mode.
73 Bill AE6JV
On 6/25/20 at 6:14 PM, jlm...@outlook.com (John McBride) wrote:
I am getting my K3 ready to use PSK31 on Field Day. 40 meters
is configured for DATA A, but I can't change 20 or 15 meters
from USB to DATA A. What direction or suggestion do you
I am getting my K3 ready to use PSK31 on Field Day. 40 meters is configured for
DATA A, but I can't change 20 or 15 meters from USB to DATA A. What direction
or suggestion do you have to make this change.
John McBride - N0UQC
__
Skip,
Make certain the K3 is getting audio into the Line In jack.
Pull the speaker or Line Out cable from your soundcard and plug
headphones or amplified computer speakers into that soundcard jack.
Then do a TX from your software application. Do you hear any audio
tones? If not, check the
Skip,
Check your soundcard cable to your Line-in jack. I had the same problem
occur several times before I discovered the problem was the cable. I
pressed on it at the line in jack while testing and the power out came
back up. Same symptoms: no output, RX signals OK, CW and SSB OK.
Replaced
On 6/30/2019 8:43 PM, Skip Cameron wrote:
Need suggestions on diagnosis or reset process.
VOX settings? Level changes? Windoze updates screwing with sound card
settings or choices?
73, Jim K9YC
__
Elecraft mailing list
Home:
While using my K3 in data A mode with wsjt-x software on 6M, TX stopped,
and other data modes also have no TX output. RX remains OK, and CW and SSB
TX & RX still work OK.
Need suggestions on diagnosis or reset process. Direct replies off list
are OK. Thanks, Skip W5GAI
Thanks Barry - K3NDM, for the assistance. Turns out WINDOWS 10 updates and not
only shut off my sound card but changed one of the com ports on my Navigator.
Goes to show that you can't assume anything will be the same after an
update.73,Bill - W0BBI
. :-)
73,
Barry
K3NDM
-- Original Message --
From: "Bill Wiehe via Elecraft" <elecraft@mailman.qth.net>
To: "Elecraft Reflector" <elecraft@mailman.qth.net>
Sent: 1/9/2017 9:21:02 PM
Subject: [Elecraft] K3 DATA A Mode not working
I recently downloaded a JT6
I recently downloaded a JT65 program and after several days of flawless
operation, my K3 stopped transmitting in DATA A mode. The K3 keys but nothing
is transmitted and no power out. I changed over to BPSK31 via HRD using DATA A
with the same results. All the other modes (RTTY FSK, CW, SSB)
So does shift, plus, question mark as in ^+?
Anybody wanna take a shot at what THAT means ?
Charlie k3ICH
- Original Message -
From: David Cole d...@nk7z.net
To: elecraft@mailman.qth.net
Sent: Wednesday, March 18, 2015 12:17 AM
Subject: Re: [Elecraft] K3 DATA A vs AFSK A
LSMFT
LSMFT had several other meanings... :)
--
Thanks and 73's,
For equipment, and software setups and reviews see:
www.nk7z.net
for MixW support see;
http://groups.yahoo.com/neo/groups/mixw/info
for Dopplergram information see:
http://groups.yahoo.com/neo/groups/dopplergram/info
for MM-SSTV see:
Hmmm ... this may be the first time Fred Cady's book has failed me. I
understand now what each mode does. What's still not clear is why
would I choose one over the other? Operator/User manuals tend not to
answer that question, they are understandably focused on exactly how to
operate the
Note: in my comment below Mark-85 Hz should be MARK+85 Hz as AFSK A
(LSB) reverses the sense of the tones - Mark is the lower of the two
audio tones but the higher of the RF frequencies.
73,
... Joe, W4TV
On 2015-03-17 6:48 PM, Fred Jensen wrote:
Hmmm ... this may be the first time Fred
... and it should be LSB because everyone knows: Low Space Means Fine
Teletype.
On 3/17/2015 4:00 PM, Joe Subich, W4TV wrote:
Note: in my comment below Mark-85 Hz should be MARK+85 Hz as AFSK A
(LSB) reverses the sense of the tones - Mark is the lower of the two
audio tones but the higher of
On Tue,3/17/2015 3:48 PM, Fred Jensen wrote:
What's still not clear is why would I choose one over the other?
Operator/User manuals tend not to answer that question, they are
understandably focused on exactly how to operate the equipment.
Hi Fred,
AFSK A and FSK are for RTTY. They are set
Which data sub-mode is used is really a user's choice and is dependent
on what data mode software is intended to be used. Some waterfall
display oriented data mode software will do fine sending and decoding
RTTY as well as other data modes. MMTTY (which is the main choice for
RTTY operation)
Per page 31 of the K3 owners manual sez
DATA A can be used for all audio-shift transmission modes, including AFSK and
PSK-31. VFO A shows the transmit suppressed carrier frequency and USB is normal
for DATA A. Compression is automatically set to 0 to reduce transmitted signal
distortion.
Can you 'splain the difference between AFSK and DATA A? I have been
running RTTY in AFSK using MMTTY and the sound in/out from my radio
laptop. Just two stereo cables using LINE IN/OUT on the back of the
K3, no other interface hardware. VOX for PTT. It seems to work fine,
am I missing
On 2015-03-17 12:41 PM, Fred Jensen wrote:
Can you 'splain the difference between AFSK and DATA A?
AFSK A and DATA A are both audio modes. AFSK A uses LSB
and FC is set to MARK - 85 Hz (the center of the two RTTY
Tones). DATA A is USB and FC is set to 1500 Hz (the center
of the transmit
I have been running DATA A with my SignaLink USB for JT65 JT9 using
WSJT-X. However I am now having some problems (interfacing with other
rig control software) that are making me question why I settled on DATA
A rather than USB?
Other than the fact DATA A inherently eliminates all potential
You can use DATA-A to do LSB too. I do this when I set up the KX3 for packet
radio, because it places the LO just nicely so I can also monitor the local CW
calling channel and my club's SSB frequency, using a separate SDR app on my PC.
73, Matt VK2RQ
On 17 Mar 2015, at 12:04 pm, Jim Brown
On Mon,3/16/2015 5:43 PM, Sam Morgan wrote:
I have run DATA A successfully for at least 5-6 years and being a
creature of habit, I hate to switch to USB unless I am forced to.
Hi Sam,
I can't think of a single good reason to use USB for data modes. Stick
with DATA A, which IS optimized for
Sam,
You are doing it right.
DATA A mode is like SSB with the following exceptions:
1) TX EQ is disabled in DATA A mode
2) Audio compression is disabled in DATA A mode.
3) one can set the audio input to LINE IN for DATA A mode - no need to
change it from MIC audio when using data modes.
I've been using WSJT-X for JT65 and JT9 on the HF bands for several months with
my K3, along with cocoaModem for PSK31. All three modes were set up with the
rig in Data A mode and everything worked fine. I'd like to try JT65 on six
meters but I'm seeing a different display on the K3 - it was
Jim,
The K3 uses up-conversion 6 m, which inverts the sidebands. It should stay in
NORM data mode on 6 meters once you've un-reversed it using the ALT switch.
73 Wayne
Six
http://www.elecraft.com
On Jun 26, 2014, at 11:34 AM, Jim Bennett w6...@mac.com wrote:
I've been using WSJT-X
Yes - I reversed it and it does stay in normal mode.
Thanks Wayne!
On Thursday, Jun 26, 2014, at Thursday, 11:41 AM, Wayne Burdick wrote:
Jim,
The K3 uses up-conversion 6 m, which inverts the sidebands. It should stay in
NORM data mode on 6 meters once you've un-reversed it using the
I want to change the center frequency of the passband/shift control. It
presently shows *1.36. I know it is changeable as I set it up to match a RTTY
program I was using when I first got the radio. I’ve read and reread the
operating manual and Fred Cady’s always helpful book with no
Try changing the SHIFT control. I'm assuming you're in AFSK A
mode
73,
matt W6NIA
On Mon, 24 Feb 2014 08:18:03 -0800, you wrote:
I want to change the center frequency of the passband/shift control. It
presently shows *1.36. I know it is changeable as I set it up to match a RTTY
program
On Mon, Feb 24, 2014 at 8:18 AM, Elliott Lawrence wa6...@roadrunner.com wrote:
I want to change the center frequency of the passband/shift control. It
presently shows *1.36. I know it is changeable as I set it up to match a
RTTY program I was using when I first got the radio.
Use the PITCH
I am having some trouble - probably cockpit error.
I have not really been working any of the W1AW/x stations on digital
modes until the past couple of days. Upon reading Fred Cady's book and
the K3 manual, I find that in AFSK A, I should be able to set the DUAL
PB. I cannot. I get an N/A
I'm sure this must be somewhere in the K3 Manual or KE7X book, but I
can't find it:
Are the TX and RX equalizers disabled in DATA A? In AFSK A?
I know DATA A sets CMP=0, and I think it sets MIC+LIN=OFF automatically.
Just getting started on JT65 and both my TX and RX EQ are set for SSB
and
E740107 K3 Owners Man D10.pdf
page 35
Receive Audio Equalization (EQ)
Two receive EQ setups are provided: one for CW
mode, and the other for voice modes. RX EQ does
not apply to DATA modes.
and the RX EQ is accomplished by where you have the LO and HI set
that's the determining factor for the
Are the TX and RX equalizers disabled in DATA A? In AFSK A?
Yes.
I know DATA A sets CMP=0, and I think it sets MIC+LIN=OFF
automatically.
DATA A and AFSK A do not automatically set MIC+LIN=OFF. However,
MIC+LIN *IS* set OFF if you select MENU:MIC SEL=LInE In.
73,
... Joe, W4TV
On
Thanks Sam, I'm old, I like manuals that lay flat on the desk because I
tend to write in them, but I think I'm going to have to download the
manual in searchable PDF.
73,
Fred K6DGW
- Northern California Contest Club
- CU in the 2014 Cal QSO Party 4-5 Oct 2014
- www.cqp.org
On 10/13/2013
Hi
K3 in DATA mode has no output if 'LINE IN' is used.
USB/LSB works fine for data modes, but DATA (DATA A) has zero output with
LINE IN ( there is not even a whisper of signal with my LP-100A). If I use
MIC instead of LINE IN; then I get an output.
Have done a factory reset to no avail;
Be sure the Tx Audio source (MIC SEL menu entry) in DATA A mode is set
to LINE IN and not MIC. The audio source in DATA mode selection is
independent of the audio source in SSB modes.
73,
Lyle KK7P
K3 in DATA mode has no output if 'LINE IN' is used.
tnx for the very prompt reply Lyle...
I just checked again DATA mode A; main menu Mic SelectLine In
and same results - absolutely no power out
73 John VE3NFK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-DATA-mode-does-not-TX-tp7568906p7568910.html
The next step us to set line in/out levels, also in the menu (tech on?). The
actual name eludes me, I'm remoting to the K3 while traveling and didn't look
at the .pdf files I carry in the phone.
And then to confirm signals at the sound card (bad cables, wrong source, etc.).
My line out is
John,
I believe Lyle intended you to check the source of your audio.
I assume you are using an interface box of some kind.
Many interface boxes have the ability to change the output from Mic
Level (usually the default) to line level. Consult your interface box
documentation to find out how
thanks for all the help guys...
After I 'cranked' 'line' to maximum; I was able to get to 75% of full
power...
So i guess I will leave it that.
Sincerely appreciate all the support
- now - what am I doing wrong with my APRS 2 meter setup (previous post)
with no answers :-)
thanks again.
73
thanks for the magic guys... WSPR 10 watts 10 minutes, DATA A mode for the
first time:
VE3NFK
Hearing: HK3DRO, KE7A, W3HH
Heard by: HK3DRO, IZ4PSG, KB9AMG, KE7A, KV0S, OE6WSF, ON7KO, TF3LB, UU1CC,
VK7DIK, W3HH, WA5ETV, YO9IRF
73 John VE3NFK
PS - I'll need to go back to the 1 milliwatt I was
John,
That does seem like your audio input is set for Mic level output.
With the K3, you cannot judge sufficient audio by the power output.
The manual covers this situation, but here is how to set the audio level
for data modes.
First set the K3 into TX TEST so you don't disturb other hams
VE3NFK wrote:
After I 'cranked' 'line' to maximum; I was able to get to 75% of full
power...
By 'line', are you referring to the sound card line level adjustment or
the K3's Line In level adjustment? Whichever one you meant, your
statement suggests either that the other one may be set too
Got my cable in today to do soundcard data modes on the K3 with a SignaLink
USB
Not much chance of getting the cabling incorrect, installation was uber
easy. I used the rear panel inputs and outputs for the additional
isolation; allowing me to keep the Mic on the front panel for mixed mode
David,
Are you following the instructions in the K3 manual, or are you trying
to follow the wisdom supplied on the internet? The K3 is different
than the internet wisdom transceivers.
The fact that you say the output is not stable leads me to believe you
are trying to use the internet wisdom
David.
I would like to point out that the K3 ALC indicator is also a level
indicator. The onset of ALC begins at the 5ht bar, and bars 1 through 4
do not indicate any ALC action at all. They are more like a VU meter
provided to allow you some metering to help you adjust the audio level.
73,
...@bellsouth.net
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Data Modes using SignaLink USB
David,
Are you following the instructions in the K3 manual, or are you trying
to follow the wisdom supplied on the internet? The K3 is different
than the internet wisdom transceivers.
The fact that you
[mailto:w3...@embarqmail.com]
Sent: Friday, October 12, 2012 11:01 PM
To: dalit...@bellsouth.net
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Data Modes using SignaLink USB
David.
I would like to point out that the K3 ALC indicator is also a level
indicator. The onset of ALC begins
Absolutely. The K3 Alc is integral to its power regulation and needs to be
set for 4 bars of ALC with the fifth bar flickering. This is also
explained in the K3 operating tips.
73
Greg
AB7R
On Oct 12, 2012 8:13 PM, Don Wilhelm w3...@embarqmail.com wrote:
it is
measuring volume units, before it switches to ALC and stabilizes.
-Original Message-
From: Don Wilhelm [mailto:w3...@embarqmail.com]
Sent: Friday, October 12, 2012 11:01 PM
To: dalit...@bellsouth.net
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Data Modes using
Greg,
I would like this to be set into the manual that the K3 is different
than the conventional wisdom given on the internet. The instructions in
the K3 manual for data modes is to be followed if the expected levels
and power settings ae to be obtained.
73,
Don W3FPR
On 10/12/2012 11:20
I agree...this comes up too often and is vital to the proper operation of
data modes.
On Oct 12, 2012 8:32 PM, Don Wilhelm w3...@embarqmail.com wrote:
Greg,
I would like this to be set into the manual that the K3 is different than
the conventional wisdom given on the internet. The
Greg,
You are absolutely correct, but other than a general post to the
Elecraft reflector, I do not know how to reach the many K2/K3 users who
do not monitor this reflector and want to try out data modes. The
information that the K2/K3 is different does not seem to appear in the
lists of data
Don speaks with knowledge.
I have my SignaLink setup exactly as he describes, which is exactly
the way the manual instructs you to set up for sound card operation.
Amateur Radio Operator N5GE
ARRL Lifetime Member
QCWA Lifetime Member
On Fri, 12 Oct 2012 23:00:59 -0400, Don Wilhelm
10:46 PM
To: dalit...@bellsouth.net
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Data Modes using SignaLink USB
David,
Are you following the instructions in the K3 manual, or are you trying
to follow the wisdom supplied on the internet? The K3 is different
than the internet
One thing that I failed to point out is that if the audio drive is not
set properly, the K3 will power hunt and you will find the SSB or data
modes power to be unpredictable. Use the instructions in he K3 manual
for data modes and the problems will go away.
73,
Don W3FPR
On 10/12/2012 11:58
I've been using my K3/100 with a Signalink USB for nearly 2 years and, once
set correctly, the pair work flawlessly. The instructions for power setting in
digital modes are repeated many times on this reflector and were hard to miss
when I went looking for help. Once you accept that it's the
I keep setting the Data MD to 45 baud fsk and somehow the radio has gone
back to 75 baud a couple of times on it's own. Anyone else seen this?
Using MMTTY 1.68.
--
Mike W0MU
W0MU-1 CC Cluster w0mu.net
__
Elecraft mailing list
This parameter is saved separately by band. Could that be the problem?
73 de Bob, K6XX
On 4/16/2012 1:58 PM, W0MU Mike Fatchett wrote:
I keep setting the Data MD to 45 baud fsk and somehow the radio has gone
back to 75 baud a couple of times on it's own. Anyone else seen this?
Using MMTTY
list.
73, Doug
- Original Message -
From: W0MU Mike Fatchett w...@w0mu.com
To: elecraft@mailman.qth.net
Sent: Monday, April 16, 2012 4:58 PM
Subject: [Elecraft] K3-Data mode RTTY
I keep setting the Data MD to 45 baud fsk and somehow the radio has gone
back to 75 baud a couple of times
Bob: I don't think so. In my case it happens while on the same band and
doesn't seem to be band dependent.
73, Doug VE3MV
- Original Message -
From: Bob Wolbert, K6XX k...@cruzio.com
To: elecraft@mailman.qth.net
Sent: Monday, April 16, 2012 5:02 PM
Subject: Re: [Elecraft] K3-Data
Yes, that is usually the problem. It happens to me all the time and I still
sometimes forget why!
73,
Ed - W0YK
-
Ed Muns
www.w0yk.com
Bob K6XX replied:
This parameter is saved separately by band. Could that be the problem?
On 4/16/2012 1:58 PM, W0MU Mike Fatchett
That could be it but this rig was used at J6 and I made a bunch of RTTY
contacts from down there and I doubt that they were made at 75 baud but
hey who knows...
Mike W0MU
W0MU-1 CC Cluster w0mu.net
On 4/16/2012 7:56 PM, Ed Muns wrote:
Yes, that is usually the problem. It happens to me all
- From: W0MU Mike Fatchett w...@w0mu.com
To: elecraft@mailman.qth.net
Sent: Monday, April 16, 2012 4:58 PM
Subject: [Elecraft] K3-Data mode RTTY
I keep setting the Data MD to 45 baud fsk and somehow the radio has gone
back to 75 baud a couple of times on it's own. Anyone else seen
Mike,
Were you using the K3's internal RTTY encoder/decoder? If you were
using software on a computer, the baud rate setting on the K3 is
irrelevant.
73,
~iain / N6ML
PS. Tnx agn for the J6 QSOs :)
On Mon, Apr 16, 2012 at 8:19 PM, W0MU Mike Fatchett w...@w0mu.com wrote:
That could be
For FSK?
Mike W0MU
W0MU-1 CC Cluster w0mu.net
On 4/16/2012 9:26 PM, iain macdonnell - N6ML wrote:
Mike,
Were you using the K3's internal RTTY encoder/decoder? If you were
using software on a computer, the baud rate setting on the K3 is
irrelevant.
73,
~iain / N6ML
PS. Tnx agn
Yes. When you use a computer to generate FSK, the timing is generated
at the the computer - it just tells the K3 when to shift frequency...
unless the software sends commands containing the text to be sent. The
K3 Utility can do that (IIRC), but most common RTTY software doesn't.
~iain / N6ML
Message - From: W0MU Mike Fatchettw...@w0mu.com
To:elecraft@mailman.qth.net
Sent: Monday, April 16, 2012 4:58 PM
Subject: [Elecraft] K3-Data mode RTTY
I keep setting the Data MD to 45 baud fsk and somehow the radio has gone
back to 75 baud a couple of times on it's own. Anyone else seen
...@w0mu.com
To:elecraft@mailman.qth.net
Sent: Monday, April 16, 2012 4:58 PM
Subject: [Elecraft] K3-Data mode RTTY
I keep setting the Data MD to 45 baud fsk and somehow the radio has
gone
back to 75 baud a couple of times on it's own. Anyone else seen this?
Using MMTTY 1.68.
--
Mike
Yes, this is a known problem. For example, the driver starts
transmitting before the FA command is complete on the first attempt to
connect, whether or not a band change is involved. It's amazing that
no one caught this in beta tests.
73,
matt W6NIA
On Sat, 07 Jan 2012 02:07:58 -0500, you
On 1/7/2012 8:46 AM, Matt Zilmer wrote:
Yes, this is a known problem. For example, the driver starts
transmitting before the FA command is complete on the first attempt to
connect, whether or not a band change is involved. It's amazing that
no one caught this in beta tests.
That is truly
Good questions, Joe. I've never gotten an answer (and yes, I've asked
around).
matt
On Sat, 07 Jan 2012 10:17:57 -0500, you wrote:
On 1/7/2012 8:46 AM, Matt Zilmer wrote:
Yes, this is a known problem. For example, the driver starts
transmitting before the FA command is complete on the
: Matt Zilmer [mailto:mzil...@verizon.net]
Sent: Sunday, January 01, 2012 11:31 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3: data modes - bizarre behavior
In all this time with K3 #24, I've never been stymied by any issue
such as described below.
I'm a Navy-Marine Corps MARS member
]
Sent: Sunday, January 01, 2012 11:31 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3: data modes - bizarre behavior
In all this time with K3 #24, I've never been stymied by any issue
such as described below.
I'm a Navy-Marine Corps MARS member. We use RMS Express in the WL2K
system
W4GRJ wrote:
Just leave the K3 in USB, do not change to data mode. RMS Express will set to
the correct freq. You will not have to make any adjustments.
If this is correct, and RMS Express tunes to the correct frequency in
USB mode but not in DATA A mode, then there may be an error in RMS
Matt
I use Airmail with my K3 and an SCS Pactor modem to connect to the
Winlink system. Using the pre-defined settings in Airmail it works
perfectly to connect to any of the mail boxes within range, no
tweaking of the RIT, etc. needed.
It looks like RMS Express is the cause of the issue, which I
I use RMS Express Winmor, DSM780 FlDigi MT63, Airmail Pactor and MIL110A,
they all work perfect with the rig left in USB.
Jack
W4GRJ / AFA4DG
On Jan 2, 2012, at 3:43, Richard Ferch ve3...@storm.ca wrote:
W4GRJ wrote:
Just leave the K3 in USB, do not change to data mode. RMS Express will
Same here, installed RMS last weekend it worked fine in USB for winmor
also on my K3 first time.
Strange.
--
*Iain Haywood*
G4SGX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Yes, of course, but that is not in the least surprising. The question
is: Why doesn't RMS Express work properly in DATA A mode? This is
precisely the kind of application that DATA A was intended for.
73,
Rich VE3KI
On 02/01/2012 7:53 AM, W4GRJ wrote:
I use RMS Express Winmor, DSM780 FlDigi
...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Richard Ferch
Sent: Monday, January 02, 2012 9:13 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: data modes - bizarre behavior
Yes, of course, but that is not in the least surprising. The question
is: Why doesn't
Subject: [Elecraft] K3: data modes - bizarre behavior
In all this time with K3 #24, I've never been stymied by any issue
such as described below.
I'm a Navy-Marine Corps MARS member. We use RMS Express in the WL2K
system on HF, running WL2K Winmor mode The software I have is version
1.1.3.0
the audio.
...bill nr4c
-Original Message-
From: Matt Zilmer [mailto:mzil...@verizon.net]
Sent: Sunday, January 01, 2012 11:31 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3: data modes - bizarre behavior
In all this time with K3 #24, I've never been stymied by any issue
I use Airmail and RMS Express and both work as they should in Pactor 1-4 mode.
RMS Express version is 1.1.3.0. Controller is a SCS DR-7800 P4 Dragon
I recommend to use DATA Mode in the K3 for Pactor.
DATA Mode should be set to DATA A, USB.
You should set RMS Express to use DATA USB.
You
In all this time with K3 #24, I've never been stymied by any issue
such as described below.
I'm a Navy-Marine Corps MARS member. We use RMS Express in the WL2K
system on HF, running WL2K Winmor mode The software I have is version
1.1.3.0.
I also use LP Bridge to create two COM ports: one
actual transmission freq is the sum of VFO
plus the audio.
...bill nr4c
-Original Message-
From: Matt Zilmer [mailto:mzil...@verizon.net]
Sent: Sunday, January 01, 2012 11:31 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3: data modes - bizarre behavior
In all this time with K3 #24
@mailman.qth.net
Subject: [Elecraft] K3: data modes - bizarre behavior
In all this time with K3 #24, I've never been stymied by any issue
such as described below.
I'm a Navy-Marine Corps MARS member. We use RMS Express in the WL2K
system on HF, running WL2K Winmor mode The software I have is version
of your radio. So you actual transmission freq is the sum of VFO
plus the audio.
...bill nr4c
-Original Message-
From: Matt Zilmer [mailto:mzil...@verizon.net]
Sent: Sunday, January 01, 2012 11:31 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3: data modes - bizarre behavior
: [Elecraft] K3: data modes - bizarre behavior
Matt,
It sounds like your software is trying to set the K3 to the channel
center frequency. Just as a guess, that might be SOP for government
gear, but not for most ham rigs which refer to the suppressed carrier
frequency..
73,
Don W3FPR
What Don is saying is certainly true for the UK military HF gear I have
used. Centre of channel is always 1500Hz higher than the suppressed
carrier frequency.
73 Stephen G4SJP
On 1 January 2012 19:48, Don Wilhelm w3...@embarqmail.com wrote:
snip
It sounds like your software is trying to set
is the sum of VFO
plus the audio.
...bill nr4c
-Original Message-
From: Matt Zilmer [mailto:mzil...@verizon.net]
Sent: Sunday, January 01, 2012 11:31 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3: data modes - bizarre behavior
In all this time with K3 #24, I've never
1 - 100 of 196 matches
Mail list logo
